Measuring nitrous oxide emissions from conventional and controlled release fertilisers in south-east Queensland pineapple production

Nitrous oxide (N2O) is a potent greenhouse gas with a global warming potential 298 times higher than carbon dioxide. Soils are a natural source of N2O, contributing 65% of global emissions. This paper is the first in Australia to measure and compare N2O emissions from pre-plant controlled release (CR) and conventional granular (CV) fertilisers in pineapple production using static PVC chambers to capture N2O emissions. Farm 1 cumulative emissions from the CR fertiliser were 3.22 kg ha-1 compared to 6.09 kg ha-1 produced by the CV. At farm 2 the CV blend emitted 2.36 kg ha-1 in comparison to the CR blend of 2.92 kg ha-1. Daily N2O flux rates showed a relationship of direct response to rainfall and soil moisture availability. High emissions were observed for wheel tracks where increased N2O emissions may be linked to soil compaction and waterlogging that creates anaerobic conditions after rain events. Emission measurements over three months highlighted the inconsistencies found in other studies relative to reducing emissions through controlled release nitrogen. More investigations are required to verify the benefits associated with controlled release fertiliser use in pineapples, placement and seasonal timing to address N2O emissions in pineapples.

Assessment of a data-limited, multi-species shark fishery in the Great Barrier Reef Marine Park and south-east Queensland

The status of five species of commercially exploited sharks within the Great Barrier Reef Marine Park (GBRMP) and south-east Queensland was assessed using a data-limited approach. Annual harvest rate, U, estimated empirically from tagging between 2011 and 2013, was compared with an analytically-derived proxy for optimal equilibrium harvest rate, UMSY Lim. Median estimates of U for three principal retained species, Australian blacktip shark, Carcharhinus tilstoni, spot-tail shark, Carcharhinus sorrah, and spinner shark, Carcharhinus brevipinna, were 0.10, 0.06 and 0.07 year-1, respectively. Median U for two retained, non-target species, pigeye shark, Carcharhinus amboinensis and Australian sharpnose shark, Rhizoprionodon taylori, were 0.27 and 0.01 year-1, respectively. For all species except the Australian blacktip the median ratio of U/UMSY Lim was <1. The high vulnerability of this species to fishing combined with life history characteristics meant UMSY Lim was low (0.04-0.07 year-1) and that U/UMSY Lim was likely to be > 1. Harvest of the Australian blacktip shark above UMSY could place this species at a greater risk of localised depletion in parts of the GBRMP. Results of the study indicated that much higher catches, and presumably higher U, during the early 2000s were likely unsustainable. The unexpectedly high level of U on the pigeye shark indicated that output-based management controls may not have been effective in reducing harvest levels on all species, particularly those caught incidentally by other fishing sectors including the recreational sector. © 2016 Elsevier B.V.

Genetic variation in growth and wood-quality traits of Corymbia citriodora subsp. variegata across three sites in south-east Queensland, Australia

Ten growth or wood-quality traits were assessed in three nearby Corymbia citriodora subsp. variegata (CCV) open-pollinated family-within-provenance trials (18 provenances represented by a total of 374 families) to provide information for the development of a breeding program targeting both pulp and solid-wood products. Growth traits (diameter at breast high over bark [DBH], height and conical volume) were assessed at 3 and 7 years of age. Wood-quality traits (density [DEN], Kraft pulp yield [KPY], modulus of elasticity [MoE] and microfibril angle [MfA]) were predicted using near-infrared spectroscopy on wood samples collected from these trials when aged between 10 and 12 years. The high average KPY, DEN and MoE, and low average MfA observed indicates CCV is very suitable for both pulp and timber products. All traits were under moderate to strong genetic control. In across- trials analyses, high (>0.4) heritability estimates were observed for height, DEN, MoE and MfA, while moderate heritability estimates (0.24 to 0.34) were observed for DBH, volume and KPY. Most traits showed very low levels of genotype × site interaction. Estimated age–age genetic correlations for growth traits were strong at both the family (0.97) and provenance (0.99) levels. Relationships among traits (additive genetic correlation estimates) were favourable, with strong and positive estimates between growth traits (0.84 to 0.98), moderate and positive values between growth and wood-quality traits (0.32 to 0.68), moderate and positive between KPY and MoE (0.64), and high and positive between DEN and MoE (0.82). However, negative (but favourable) correlations were detected between MfA and all other evaluated traits (−0.31 to −0.96). The genetic correlation between the same trait expressed on two different sites, at family level, ranged from 0.24 to 0.42 for growth traits, and from 0.29 to 0.53 for wood traits. Therefore simultaneous genetic improvement of growth and wood property traits in CCV for the target environment in south-east Queensland should be possible, given the moderate to high estimates of heritability and favourable correlations amongst all traits studied, unless genotype × site interactions are greater than was evident. © 2016 NISC (Pty) Ltd

The tolerance of steers (Bos taurus) to sorghum ergot (Claviceps africana) in a feedlot during the cooler months in sub-tropical Queensland

Two experiments tested the tolerance of steers (Bos taurus) to sorghum ergot (Claviceps africana) during cooler months in south-east Queensland. Sorghum grain containing 2.8% ergot and 28 mg/kg ergot alkaloids (84% dihydroergosine, 10% dihydroelymoclavine, 6% festuclavine) was incorporated into feedlot rations. In a previous study in summer–autumn, ergot (1.1–4.4 mg alkaloids/kg ration) severely reduced performance in steers when the temperature–humidity index (THI; dry bulb temperature °C + 0.36 dew-point temperature °C + 41.2) was ~70, whereas a THI of ~79 was tolerated by steers fed ergot-free rations. Experiment 1 was conducted in winter–spring, with rations containing 0, 2.8, 5.6, 8.2 or 11.2 mg ergot alkaloids/kg ration. All ergot inclusions depressed feed intake (14% average reduction) and growth rate (34% average reduction), even when the weekly average daily THI was less than 65. Rectal temperatures were occasionally elevated in ergot-fed steers (P < 0.05), primarily when the THI exceeded ~65. All ergot inclusions depressed plasma prolactin concentrations in steers. Experiment 2 was predominantly carried out in winter, with weekly average daily THI <65 throughout the experiment. Rations containing 0, 0.28, 0.55 or 1.1 mg ergot alkaloids/kg were fed for 4 weeks but produced no significant effect on feed intakes and growth rates of steers. Alkaloid concentrations were then changed to 0, 2.1, 4.3 and 1.1 mg/kg, respectively. Subsequently, feed intakes declined by 17.5% (P < 0.05), and growth rates by 28% (P > 0.05) in the group receiving 4.3 mg/kg alkaloid, compared with Controls. Plasma prolactin concentrations were depressed, relative to the Controls, by dietary alkaloid inclusion greater than 1.1 mg/kg, with alkaloid intake of 4.3 mg/kg causing the greatest reduction (P < 0.05). Cattle performance in these studies shows steers can tolerate up to ~2 mg ergot alkaloid/kg (0.2% ergot) in feedlot rations under low THI conditions (< ~60–65), but previous findings indicate a much lower threshold will apply at higher THI (>65).

The tolerance of steers (Bos taurus) to sorghum ergot (Claviceps africana) in a feedlot during the cooler months in sub-tropical Queensland

Two experiments tested the tolerance of steers (Bos taurus) to sorghum ergot (Claviceps africana) during cooler months in south-east Queensland. Sorghum grain containing 2.8% ergot and 28 mg/kg ergot alkaloids (84% dihydroergosine, 10% dihydroelymoclavine, 6% festuclavine) was incorporated into feedlot rations. In a previous study in summer–autumn, ergot (1.1–4.4 mg alkaloids/kg ration) severely reduced performance in steers when the temperature–humidity index (THI; dry bulb temperature °C + 0.36 dew-point temperature °C + 41.2) was ~70, whereas a THI of ~79 was tolerated by steers fed ergot-free rations. Experiment 1 was conducted in winter–spring, with rations containing 0, 2.8, 5.6, 8.2 or 11.2 mg ergot alkaloids/kg ration. All ergot inclusions depressed feed intake (14% average reduction) and growth rate (34% average reduction), even when the weekly average daily THI was less than 65. Rectal temperatures were occasionally elevated in ergot-fed steers (P < 0.05), primarily when the THI exceeded ~65. All ergot inclusions depressed plasma prolactin concentrations in steers. Experiment 2 was predominantly carried out in winter, with weekly average daily THI <65 throughout the experiment. Rations containing 0, 0.28, 0.55 or 1.1 mg ergot alkaloids/kg were fed for 4 weeks but produced no significant effect on feed intakes and growth rates of steers. Alkaloid concentrations were then changed to 0, 2.1, 4.3 and 1.1 mg/kg, respectively. Subsequently, feed intakes declined by 17.5% (P < 0.05), and growth rates by 28% (P > 0.05) in the group receiving 4.3 mg/kg alkaloid, compared with Controls. Plasma prolactin concentrations were depressed, relative to the Controls, by dietary alkaloid inclusion greater than 1.1 mg/kg, with alkaloid intake of 4.3 mg/kg causing the greatest reduction (P < 0.05). Cattle performance in these studies shows steers can tolerate up to ~2 mg ergot alkaloid/kg (0.2% ergot) in feedlot rations under low THI conditions (< ~60–65), but previous findings indicate a much lower threshold will apply at higher THI (>65).

Comparison of growth traits between abundant and uncommon forms of a non-native vine, Dolichandra unguis-cati (Bignoniaceae) in Australia

Cat’s claw creeper vine, Dolichandra unguis-cati (L.) Lohmann (syn. Macfadyena unguis-cati (L.) Gentry) (Bignoniaceae), is a major environmental weed in Australia. Two distinct forms of this weed (‘long’ and ‘short’ pod), with differences in leaf morphology and fruit size, occur in Australia. The long pod form has only been reported in less than fifteen localities in the whole of south-east Queensland, while the short pod form is widely distributed in Queensland and New South Wales. This study sought to compare growth traits such as specific leaf area, relative growth rate, stem length, shoot/root ratio, tuber biomass and branching architecture between these forms. These traits were monitored under glasshouse conditions over a period of 18 months. Short pod exhibited higher values of relative growth rates, stem length, number of tubers and specific leaf area than long pod, but only after 10 months of plant growth. Prior to this, long and short pod did not differ significantly. Higher values for these traits have been described as characteristics of successful colonizers. Results from this study could partly explain why the short pod form is more widely distributed in Australia while long pod is confined to a few localities.

Efficiency of rumen microbial protein synthesis in cattle grazing tropical pastures as estimated by a novel technique

The efficiency of microbial protein synthesis (EMPS) in cattle grazing a range of tropical pasture types was examined using a new method of intra-jugular infusion of CrEDTA to estimate urinary excretion of purine derivatives (PD). Seven pasture types were studied in south-east Queensland, Australia, over a 13-month period. These included native tropical grass (C4) pasture (major species Heteropogon contortus and Bothriochloa bladhii) studied in the early wet, the wet/dry transition and the dry season; introduced tropical grass (C4) pasture (Bothriochloa insculpta) in the mid wet season; two introduced tropical legume species (C3), (Lablab purpureus and Clitoria ternatea); and the temperate grass (C3) pasture, ryegrass (Lolium multiflorum). There was a large range in EMPS across pasture types: 26-209 g microbial crude protein (MCP)/kg digestible organic matter intake (DOMI). Estimated rumen degradable protein (RDP) supply (42-525 g/kg DOMI) was the major factor associated with EMPS across the range of pasture types studied. EMPS in steers grazing all tropical grass pastures was low (<130 g/kg DOMI) and limited by RDP supply. Negative linear relationships (P<0.05) between EMPS and both neutral detergent fibre (NDF) and acid detergent fibre (ADF) concentrations in extrusa were evident. However, non-fibre carbohydrate in extrusa, total non-structural carbohydrate concentration in plucked pasture leaf, rumen fluid and particle dilution rate, protozoal concentration in rumen fluid and rumen fluid pH were not correlated with EMPS. It was concluded that EMPS was well below 130 g MCP/kg DOMI when cattle grazed unfertilised, tropical grass pastures in south-east Queensland and that RDP was the primary limiting nutrient. High EMPS was associated with very high RDP, vastly in excess of RDP requirements by microbes

Thrips incidence in green beans and the degree of damage caused

Green bean production accounts for 2.4% of the total value of Australian vegetable production and was Australia's tenth largest vegetable crop in 2008-2009 by value. Australian green bean production is concentrated in Queensland (51%) and Tasmania (34%) where lost productivity as a direct result of insect damage is recognised as a key threat to the industry (AUSVEG, 2011). Green beans attract a wide range of insect pests, with thrips causing the most damage to the harvestable product, the pod. Thrips populations were monitored in green bean crops in the Gatton Research Facility, Lockyer Valley, South-east Queensland, Australia from 2002-2011. Field trials were conducted to identify the thrips species present, to record fluctuation in abundance during the season and assess pod damage as a direct result of thrips. Thirteen species of thrips were recorded during this time on bean plantings, with six dominant species being collected during most of the growing season: Frankliniella occidentalis, F. schultzei, Megalurothrips usitatus, Pseudanaphothrips achaetus, Thrips imaginis and T. tabaci. Thrips numbers ranged from less than one thrips per flower to as high as 5.39 thrips per flower. The highest incidence of thrips presence found in October/November 2008, resulted in 10.74% unmarketable pods due to thrips damage, while the lowest number of thrips recorded in April 2008 caused a productivity loss of 36.65% of pods as a result of thrips damage.

Nineteenth century narratives reveal historic catch rates for Australian snapper (Pagrus auratus)

Snapper (Pagrus auratus) is widely distributed throughout subtropical and temperate southern oceans and forms a significant recreational and commercial fishery in Queensland, Australia. Using data from government reports, media sources, popular publications and a government fisheries survey carried out in 1910, we compiled information on individual snapper fishing trips that took place prior to the commencement of fisherywide organized data collection, from 1871 to 1939. In addition to extracting all available quantitative data, we translated qualitative information into bounded estimates and used multiple imputation to handle missing values, forming 287 records for which catch rate (snapper fisher−1 h−1) could be derived. Uncertainty was handled through a parametric maximum likelihood framework (a transformed trivariate Gaussian), which facilitated statistical comparisons between data sources. No statistically significant differences in catch rates were found among media sources and the government fisheries survey. Catch rates remained stable throughout the time series, averaging 3.75 snapper fisher−1 h−1 (95% confidence interval, 3.42–4.09) as the fishery expanded into new grounds. In comparison, a contemporary (1993–2002) south-east Queensland charter fishery produced an average catch rate of 0.4 snapper fisher−1 h−1 (95% confidence interval, 0.31–0.58). These data illustrate the productivity of a fishery during its earliest years of development and represent the earliest catch rate data globally for this species. By adopting a formalized approach to address issues common to many historical records – missing data, a lack of quantitative information and reporting bias – our analysis demonstrates the potential for historical narratives to contribute to contemporary fisheries management.

Reproductive parameters of rhinobatid and urolophid batoids taken as by-catch in the Queensland (Australia) east coast otter-trawl fishery

Reproductive variables are provided for batoids regularly taken as by-catch in the east coast otter-trawl fishery on the inner-mid continental shelf off the south-east and central coasts of Queensland, Australia. Total length at maturity (LT50 and 95% c.i.) for the eastern shovelnose ray Aptychotrema rostrata was 639·5 mm (617·6–663·4 mm) for females and 597·3 mm (551·4–648·6 mm) for males. Litter size (n = 9) ranged from nine to 20 (mean ± s.e. = 15·1 ± 1·2). This species exhibited a positive litter size–maternal size relationship. Disc width at maturity (WD50 and 95% c.i.) for the common stingaree Trygonoptera testacea was 162·7 mm (155·8–168·5 mm) for females and 145·9 mm (140·2–150·2 mm) for males. Gravid T. testacea (n = 6) each carried a single egg in the one functional (left) uterus. Disc width at maturity (WD50 and 95% c.i.) for the Kapala stingaree Urolophus kapalensis was 153·7 mm (145·1–160·4 mm) for females and 155·2 mm (149·1–159·1 mm) for males. Gravid U. kapalensis (n = 16) each carried a single egg or embryo in the one functional (left) uterus. A single female yellowback stingaree Urolophus sufflavus carried an embryo in each uterus. A global review of the litter sizes of shovelnose rays (Rhinobatidae) and stingarees (Urolophidae) is provided.

An investigation of environmental conditions experienced during the life of high-value wood components and products

Australian forest industries have a long history of export trade of a wide range of products from woodchips (for paper manufacturing), sandalwood (essential oils, carving and incense) to high value musical instruments, flooring and outdoor furniture. For the high value group, fluctuating environmental conditions brought on by changes in temperature and relative humidity, can lead to performance problems due to consequential swelling, shrinkage and/or distortion of the wood elements. A survey determined the types of value-added products exported, including species and dimensions packaging used and export markets. Data loggers were installed with shipments to monitor temperature and relative humidity conditions. These data were converted to timber equilibrium moisture content values to provide an indication of the environment that the wood elements would be acclimatising to. The results of the initial survey indicated that primary high value wood export products included guitars, flooring, decking and outdoor furniture. The destination markets were mainly located in the northern hemisphere, particularly the United States of America, China, Hong Kong, Europe (including the United Kingdom), Japan, Korea and the Middle East. Other regions importing Australian-made wooden articles were south-east Asia, New Zealand and South Africa. Different timber species have differing rates of swelling and shrinkage, so the types of timber were also recorded during the survey. Results from this work determined that the major species were ash-type eucalypts from south-eastern Australia (commonly referred to in the market as Tasmanian oak), jarrah from Western Australia, spotted gum, hoop pine, white cypress, black butt, brush box and Sydney blue gum from Queensland and New South Wales. The environmental conditions data indicated that microclimates in shipping containers can fluctuate extensively during shipping. Conditions at the time of manufacturing were usually between 10 and 12% equilibrium moisture content, however conditions during shipping could range from 5 (very dry) to 20% (very humid). The packaging systems incorporated were reported to be efficient at protecting the wooden articles from damage during transit. The research highlighted the potential risk for wood components to ‘move’ in response to periods of drier or more humid conditions than those at the time of manufacturing, and the importance of engineering a packaging system that can account for the environmental conditions experienced in shipping containers. Examples of potential dimensional changes in wooden components were calculated based on published unit shrinkage data for key species and the climatic data returned from the logging equipment. The information highlighted the importance of good design to account for possible timber movement during shipping. A timber movement calculator was developed to allow designers to input component species, dimensions, site of manufacture and destination, to see validate their product design.

Soybean Stem Fly, Melanagromyza sojae (Diptera: Agromyzidae), in the New World: detection of high genetic diversity from soybean fields in Brazil

Soybean Stem Fly (SSF), Melanagromyza sojae (Zehntner), belongs to the family Agromyzidae and is highly polyphagous, attacking many plant species of the family Fabaceae, including soybean and other beans. SSF is regarded as one of the most important pests in soybean fields of Asia (e.g., China, India), North East Africa (e.g., Egypt), parts of Russia, and South East Asia. Despite reports of Agromyzidae flies infesting soybean fields in Rio Grande do Sul State (Brazil) in 1983 and 2009 and periodic interceptions of SSF since the 1940s by the USA quarantine authorities, SSF has not been officially reported to have successfully established in the North and South Americas. In South America, M. sojae was recently confirmed using morphology and its complete mitochondrial DNA (mtDNA) was characterized. In the present study, we surveyed the genetic diversity of M. sojae, collected directly from soybean host plants, using partial mtDNA cytochrome oxidase I (COI) gene, and provide evidence of multiple (>10) maternal lineages in SSF populations in South America, potentially representing multiple incursion events. However, a single incursion involving multiple-female founders could not be ruled out. We identified a haplotype that was common in the fields of two Brazilian states and the individuals collected from Australia in 2013. The implications of SSF incursions in southern Brazil are discussed in relation to the current soybean agricultural practices, highlighting an urgent need for better understanding of SSF population movements in the New World, which is necessary for developing effective management options for this significant soybean pest. © FUNPEC-RP.

Transcriptome Analysis of Capsicum Chlorosis Virus-Induced Hypersensitive Resistance Response in Bell Capsicum

Background Capsicum chlorosis virus (CaCV) is an emerging pathogen of capsicum, tomato and peanut crops in Australia and South-East Asia. Commercial capsicum cultivars with CaCV resistance are not yet available, but CaCV resistance identified in Capsicum chinense is being introgressed into commercial Bell capsicum. However, our knowledge of the molecular mechanisms leading to the resistance response to CaCV infection is limited. Therefore, transcriptome and expression profiling data provide an important resource to better understand CaCV resistance mechanisms. Methodology/Principal Findings We assembled capsicum transcriptomes and analysed gene expression using Illumina HiSeq platform combined with a tag-based digital gene expression system. Total RNA extracted from CaCV/mock inoculated CaCV resistant (R) and susceptible (S) capsicum at the time point when R line showed a strong hypersensitive response to CaCV infection was used in transcriptome assembly. Gene expression profiles of R and S capsicum in CaCV- and buffer-inoculated conditions were compared. None of the genes were differentially expressed (DE) between R and S cultivars when mock-inoculated, while 2484 genes were DE when inoculated with CaCV. Functional classification revealed that the most highly up-regulated DE genes in R capsicum included pathogenesis-related genes, cell death-associated genes, genes associated with hormone-mediated signalling pathways and genes encoding enzymes involved in synthesis of defense-related secondary metabolites. We selected 15 genes to confirm DE expression levels by real-time quantitative PCR. Conclusion/Significance DE transcript profiling data provided comprehensive gene expression information to gain an understanding of the underlying CaCV resistance mechanisms. Further, we identified candidate CaCV resistance genes in the CaCV-resistant C. annuum x C. chinense breeding line. This knowledge will be useful in future for fine mapping of the CaCV resistance locus and potential genetic engineering of resistance into CaCV-susceptible crops.