Identification of QTL for sugar-related traits in a sweet x grain sorghum (Sorghum bicolor L. Moench) recombinant inbred population

QTL for stem sugar-related and other agronomic traits were identified in a converted sweet (R9188) × grain (R9403463-2-1) sorghum population. QTL analyses were conducted using phenotypic data for 11 traits measured in two field experiments and a genetic map comprising 228 SSR and AFLP markers grouped into 16 linkage groups, of which 11 could be assigned to the 10 sorghum chromosomes (SBI-01 to SBI-10). QTL were identified for all traits and were generally co-located to five locations (SBI-01, SBI-03, SBI-05, SBI-06 and SBI-10). QTL alleles from R9188 were detected for increased sucrose content and sugar content on SBI-01, SBI-05 and SBI-06. R9188 also contributed QTL alleles for increased Brix on SBI-05 and SBI-06, and increased sugar content on SBI-03. QTL alleles from R9403463-2-1 were found for increased sucrose content and sucrose yield on SBI-10, and increased glucose content on SBI-07. QTL alleles for increased height, later flowering and greater total dry matter yield were located on SBI-01 of R9403463-2-1, and SBI-06 of R9188. QTL alleles for increased grain yield from both R9403463-2-1 and R9188 were found on SBI-03. As an increase in stem sugars is an important objective in sweet sorghum breeding, the QTL identified in this study could be further investigated for use in marker-assisted selection of sweet sorghum.

Ageing delays the cellular stages of adventitious root formation in pine.

Vegetative propagation programs internationally are affected by the significant decline of rooting success as trees mature. This study compared the cellular stages of root formation in stem cuttings from 15-week-old (juvenile) and 9-y-old (mature) stock plants of the slash x Caribbean pine hybrid (Pinus elliottii var. elliottii x P. caribaea van hondurensis). The cellular stages of root formation were the same in both juvenile and mature cuttings, beginning with cell divisions of the vascular cambium forming callus tissue. Within the callus, tracheids differentiated and elongated to form root primordia. Roots in juvenile cuttings developed faster than those in mature cuttings and the juvenile cuttings had a much higher rooting percent at the end of the study (92% and 26% respectively). Cuttings of the two juvenile genotypes had more primary roots (5.5 and 3.3) than the three mature genotypes (0.96, 0.18 and 0.07). The roots of juvenile cuttings were more evenly distributed around the basal circumference when compared with those on cuttings from the mature genotypes. Further work is needed to improve understanding of physiological changes with maturation so that the rooting success and the speed of development in cuttings from mature stock plants can be optimised, hence improving genetic gain.

Characterisation of accessions and species of Macadamia to stem infection by Phytophthora cinnamomi

Phytophthora cinnamomi is a major pathogen in most macadamia plantations worldwide. Due to stem lesions, stem cankers and leaf defoliation it results in loss of productivity and tree death. In this study we examined accessions of the four Macadamia species and their hybrids, produced via rooted stem cuttings or germinated seeds, for susceptibility to stem canker and necrotic lesion caused by P. cinnamomi. Plants were wound-inoculated with agar containing P. cinnamomi. The symptoms produced in inoculated plants were used to characterize host susceptibility variation within and among the population. Lesion lengths and severity of stem canker were recorded. The four species and hybrids differed significantly in stem canker severity (P < 0.001) and lesion length (P = 0.04). M. integrifolia and M. tetraphylla hybrids were the most susceptible. M. integrifolia had the greatest stem canker severity and the most extensive lesions above and below the site of inoculation. Restricted lesion sizes were observed in M. ternifolia and M. jansenii. The effects of basal stem diameter and the method of propagation either from cuttings or seed were not significant. The genetic variation in the reactions of macadamia accessions to stem infection by P. cinnamomi is discussed.

Rotary veneering of plantation-grown spotted gum (Corymbia citriodora subsp. variegata) and Dunn's white gum (Eucalyptus dunnii)

This report evaluates the wood and veneer properties of plantation-grown spotted gum (Corymbia citriodora subsp. variegata, or CCV) and Dunn's white gum (Eucalyptus dunnii), grown at different stockings, in thinning trials near Ellangowan in north-east New South Wales (mean annual rainfall 1050 mm) and Kingaroy in south-east Queensland (mean annual rainfall 873 mm). Thinning trials were established at age seven years. Both species showed a significant increase in stem diameter growth of the dominant trees in response to thinning. At age 10 years, trees from the unthinned (950–1270 stems ha-1) and 300 stems ha-1 treatments were selected for veneering. Five dominant trees were felled from each combination of species x sites x thinning treatment. Diameter at breast height over bark of the selected trees ranged from 20 cm to 27 cm at Ellangowan, and 19 cm to 26 cm at Kingaroy. From each tree, 1.5 m long billets were removed at two positions: a butt billet from 0.3–1.8 m above ground and a top billet from approximately 5.5–7.0 m. Log end splitting was assessed 24 hours after harvesting and again after steaming, approximately four days after harvesting. Disks from just above both billets were collected for assessment of wood properties. Billets were peeled on a spindleless veneer lathe to produce a full veneer ribbon with a target green thickness of 2.8 to 3.0 mm. The 1.55 m wide (tangential dimension) veneer sheets were dried and graded according to AS/NZ Standard 2269:2008, which describes four veneer grades. Veneer samples taken along the length of the veneer ribbon, at regular intervals of 1.55 m, were tested for stiffness, shrinkage and density. Veneer length measurements were used to calculate the radial distance of each sample from the central axis of the billet. Overall veneer gross recoveries ranged from 50% to 70%. They were significantly lower at the Kingaroy site, for both species. The veneer recoveries achieved were 2–3 times higher than typical green off saw recoveries from small plantation hardwood logs of similar diameter. Most of the veneer recovered was classified as D-grade. CCV trees from the Ellangowan site yielded up to 38% of the better C-grade and higher grade veneers. The main limiting factors that prevented veneer from meeting higher grades were the presence of kino defects and encased knots. Splits in E. dunnii veneer also contributed to reduced grade quality. Log end splits were higher for E. dunnii than for CCV, and logs from Ellangowan exhibited more severe splitting. Split index was generally higher for top than for butt billets. Split index was strongly correlated with the average veneer grade from corresponding billets. The Ellangowan site, where rainfall was higher and trees grew faster, yielded significantly denser and stiffer veneers than did the drier sites near Kingaroy, where tree growth was slower. The difference was more pronounced for E. dunnii than for CCV. Differences in measured wood properties between thinned and unthinned treatments were generally small and not significant. On average, 10% of billet volume was lost during the peeling rounding-up process. Much of the wood laid down following thinning was removed during rounding-up, meaning the effect of thinning on veneer properties could not be effectively assessed. CCV was confirmed as having high veneer density and very good veneer stiffness, exceeding 15 GPa, making it very suitable for structural products. E. dunnii also demonstrated good potential as a useful structural plywood resource, achieving stiffness above 10 GPa. Veneer stiffness and density in CCV increased from pith to bark at both sites, while for E. dunnii there was a radial increase in these properties at the Ellangowan site only. At the drier Kingaroy site, veneer stiffness and density declined from mid-radius to the log periphery. This may be associated with prolonged drought from 2005 to 2009, corresponding to the later years of tree growth at the Kingaroy site. CCV appeared to be less sensitive to drought conditions. Standing tree acoustic velocity, determined by the Fakopp time-of-flight method, provided a reliable prediction of average veneer stiffness for both species (R2=0.78 for CCV and R2=0.90 for E. dunnii) suggesting that the Fakopp method may be a useful indicator of tree and stand quality, in terms of veneer stiffness in standing trees.