Control of rabbits in arid Australia: destroying the drought refuge

Rabbits continued to infest Bulloo Downs in southwest Queensland even after rabbit haemorrhagic disease virus (RHDV) had effectively reduced rabbit populations to very low levels in most other arid parts of Australia. Control efforts for over 100 years have all appeared unable to stop rabbits causing damage to cattle production and native plants and animals in the area. In 2001 an experiment established to measure the benefit of rabbit control to biodiversity and cattle production showed warren ripping to cause an immediate reduction in rabbit activity. Three months after ripping there were still 98% fewer rabbits in ripped plots despite these plots being exposed to invasion from surrounding populations. The cost of ripping was high because of the high density of warrens and is prohibitive for a full-scale programme. Nevertheless, ripping warrens just in the rabbit’s drought refuge (2002 -2004) appears to have effectively controlled rabbits over the entire property. Following one good season rabbits still have not recovered where the drought refuge was effectively ripped. Destroying warrens in the areas where rabbits survived droughts achieved a reduction in rabbits of over 99% ompared to a similar area near Coongie Lakes in South Australia. Low rabbit numbers allowed cattle to continue to be run on the property even though the area experienced seven consecutive years with below average rainfall. It still remains to be seen whether rabbits can recover from this low population-base during a run of good seasons. If rabbit numbers remain suppressed after a run of good seasons then rabbit control by destruction of drought refuge could be repeated at Coongie Lakes and other drought refuge areas in the arid zone. Identification and treatment of areas similar to Bulloo Downs where rabbits survive drought may relieve a very large area of arid Australia from the damage caused by rabbits.

An investigation of migration and possible stock structuring by the stout whiting, Sillago robusta, in southern Queensland waters, and its impact on managing the fishery. Final Report on the Pilot Program

A highly polymorphic genetic locus of Stout Whiting was examined for evidence of geographical subdivision amongst samples collected from three locales in southern Queensland waters. Statistical indicators of subdivision were not significantly different from zero, suggesting that it is unlikely that the Stout Whiting resource in southern Queensland is genetically subdivided into separate stocks. It is recommended that the full-scale genetic program not proceed and that the resource be managed as a single stock.

How can warren destruction by ripping control European wild rabbits (Oryctolagus cuniculus) on large properties in the Australian arid zone?

Context: For over 100 years, control efforts have been unable to stop rabbits causing damage to cattle production and native plants and animals on large properties in arid parts of Australia. Warren destruction by ripping has shown promise, but doubts about long-term success and the perceived expense of treating vast areas have led to this technique not being commonly used. Aims: This study measured the long-term reduction in rabbit activity and calculated the potential cost saving associated with treating just the areas where rabbits are believed to survive drought. Wealso considered whether ripping should be used in a full-scale rabbit control program on a property where rabbits have been exceptionally resilient to the influence of biological and other control measures. Methods: Rabbits were counted along spotlight transects before warrens were ripped and during the two years after ripping, in treated and untreated plots. Rabbit activity was recorded to determine the immediate and long-term impact of ripping, up to seven years after treatment. The costs of ripping warrens within different distances from drought refuge areas were calculated. Key results: Destroying rabbit warrens by ripping caused an immediate reduction in rabbit activity and there were still 98% fewer rabbits counted by spotlight in ripped plots five months after ripping. Seven years after ripping no active warrens were found in ripped plots, whereas 57% of warrens in unripped plots showed signs of rabbit activity. The cost of ripping only the areas where rabbits were likely to seek refuge from drought was calculated to be less than 4%of the cost of ripping all warrens on the property. Conclusions: Destroying rabbit warrens by ripping is a very effective way of reducing rabbit numbers on large properties in arid Australia. Ripping should commence in areas used by rabbits to survive drought. It is possible that no further ripping will be required. Implications: Strategic destruction of warrens in drought refuge areas could provide an alternative to biological control for managing rabbits on large properties in the Australian arid zone.

Duckweed-based Wastewater Treatment Systems: Design Aspects and Integrated Reuse Options for Queensland Conditions

Point sources of wastewater pollution, including effluent from municipal sewage treatment plants and intensive livestock and processing industries, can contribute significantly to the degradation of receiving waters (Chambers et al. 1997; Productivity Commission 2004). This has led to increasingly stringent local wastewater discharge quotas (particularly regarding Nitrogen, Phosphorous and suspended solids), and many municipal authorities and industry managers are now faced with upgrading their existing treatment facilities in order to comply. However, with high construction, energy and maintenance expenses and increasing labour costs, traditional wastewater treatment systems are becoming an escalating financial burden for the communities and industries that operate them. This report was generated, in the first instance, for the Burdekin Shire Council to provide information on design aspects and parameters critical for developing duckweed-based wastewater treatment (DWT) in the Burdekin region. However, the information will be relevant to a range of wastewater sources throughout Queensland. This information has been collated from published literature and both overseas and local studies of pilot and full-scale DWT systems. This report also considers options to generate revenue from duckweed production (a significant feature of DWT), and provides specifications and component cost information (current at the time of publication) for a large-scale demonstration of an integrated DWT and fish production system.

Downstream processing of reverse osmosis brine: Characterisation of potential scaling compounds

Reverse osmosis (RO) brine produced at a full-scale coal seam gas (CSG) water treatment facility was characterized with spectroscopic and other analytical techniques. A number of potential scalants including silica, calcium, magnesium, sulphates and carbonates, all of which were present in dissolved and non-dissolved forms, were characterized. The presence of spherical particles with a size range of 10–1000 nm and aggregates of 1–10 microns was confirmed by transmission electron microscopy (TEM). Those particulates contained the following metals in decreasing order: K, Si, Sr, Ca, B, Ba, Mg, P, and S. Characterization showed that nearly one-third of the total silicon in the brine was present in the particulates. Further, analysis of the RO brine suggested supersaturation and precipitation of metal carbonates and sulphates during the RO process should take place and could be responsible for subsequently capturing silica in the solid phase. However, the precipitation of crystalline carbonates and sulphates are complex. X-ray diffraction analysis did not confirm the presence of common calcium carbonates or sulphates but instead showed the presence of a suite of complex minerals, to which amorphous silica and/or silica rich compounds could have adhered. A filtration study showed that majority of the siliceous particles were less than 220 nm in size, but could still be potentially captured using a low molecular weight ultrafiltration membrane.

Downstream processing of reverse osmosis brine: Characterisation of potential scaling compounds

Reverse osmosis (RO) brine produced at a full-scale coal seam gas (CSG) water treatment facility was characterized with spectroscopic and other analytical techniques. A number of potential scalants including silica, calcium, magnesium, sulphates and carbonates, all of which were present in dissolved and non-dissolved forms, were characterized. The presence of spherical particles with a size range of 10-1000nm and aggregates of 1-10 microns was confirmed by transmission electron microscopy (TEM). Those particulates contained the following metals in decreasing order: K, Si, Sr, Ca, B, Ba, Mg, P, and S. Characterization showed that nearly one-third of the total silicon in the brine was present in the particulates. Further, analysis of the RO brine suggested supersaturation and precipitation of metal carbonates and sulphates during the RO process should take place and could be responsible for subsequently capturing silica in the solid phase. However, the precipitation of crystalline carbonates and sulphates are complex. X-ray diffraction analysis did not confirm the presence of common calcium carbonates or sulphates but instead showed the presence of a suite of complex minerals, to which amorphous silica and/or silica rich compounds could have adhered. A filtration study showed that majority of the siliceous particles were less than 220nm in size, but could still be potentially captured using a low molecular weight ultrafiltration membrane. © 2015 Elsevier Ltd.

Development and testing of an evaluation procedure for commercial manure additive products.

Manure additive products can be used to reduce odour emissions (OE) from livestock farms. The standardised evaluation of these manure additive products under specific farm conditions is important. In this study, the efficacy of a manure additive (WonderTreat(TM), CKLS, Inc., Hong-Kong) was assessed under Australian conditions utilising a combination of laboratory and field-scale evaluation techniques. As a first step, the efficacy of the manure additive was assessed in a laboratory-scale trial using a series of uniformly managed digesters and standard odour, liquor ammonia and hydrogen sulphide concentration measurement procedures. This showed that the addition of WonderTreat(TM) at the 'low dose rate' (LDR) (102.6 g m-2) used during the trial significantly, but only marginally (30%; P = 0.02) reduced the OE rate (mean 13.9 OU m-2 s-1) of anaerobic pig liquor relative to an untreated control (UC) (19.9 OU m-2 s-1). However, the 'high dose rate' (HDR) (205.3 g m-2) also assessed during the trial preformed similarly (19.7 OU m-2 s-1) to the UC. No statistically significant difference in the concentrations of a range of measured water quality variables at the 5% level was observed between the treatments or controls digesters. As a second step, a field-scale assessment of the manure additive was undertaken at a commercial piggery. Two piggery manure lagoons (each with approximately 2500 m2 surface area) were included in the study; one was treated with WonderTreat(TM) while the other was used as control. The efficacy of the treatment was assessed using olfactometric evaluation of odour samples collected from the surface of the pond using a dynamic wind tunnel and ancillary equipment. No statistically significant reduction in OE rate could be demonstrated (P = 0.35), partially due to the limited number of samples taken during the assessment. However, there was a numerical reduction in the average OE rate of the treatment pond (29 OU m-2 s-1 at 1 m s-1) compared to the control lagoon (38 OU m-2 s-1 at 1 m s-1).

Tertiary Treatment of Ayr Municipal Wastewater using Bioremediation: A Pilot-Scale Study. A Report Prepared for the Burdekin Shire Council and the Burdekin Rangeland Reef Initiative

This joint DPI/Burdekin Shire Council project assessed the efficacy of a pilot-scale biological remediation system to recover Nitrogen (N) and Phosphorous (P) nutrients from secondary treated municipal wastewater at the Ayr Sewage Treatment Plant. Additionally, this study considered potential commercial uses for by-products from the treatment system. Knowledge gained from this study can provide directions for implementing a larger-scale final effluent treatment protocol on site at the Ayr plant. Trials were conducted over 10 months and assessed nutrient removal from duckweed-based treatments and an algae/fish treatment – both as sequential and as stand-alone treatment systems. A 42.3% reduction in Total N was found through the sequential treatment system (duckweed followed by algae/fish treatment) after 6.6 days Effluent Retention Time (E.R.T.). However, duckweed treatment was responsible for the majority of this nutrient recovery (7.8 times more effective than algae/fish treatment). Likewise, Total P reduction (15.75% reduction after 6.6 days E.R.T.) was twice as great in the duckweed treatment. A phytoplankton bloom, which developed in the algae/fish tanks, reduced nutrient recovery in this treatment. A second trial tested whether the addition of fish enhanced duckweed treatment by evaluating systems with and without fish. After four weeks operation, low DO under the duckweed blanket caused fish mortalities. Decomposition of these fish led to an additional organic load and this was reflected in a breakdown of nitrogen species that showed an increase in organic nitrogen. However, the Dissolved Inorganic Nitrogen (DIN: ammonia, nitrite and nitrate) removal was similar between treatments with and without fish (57% and 59% DIN removal from incoming, respectively). Overall, three effluent residence times were evaluated using duckweed-based treatments; i.e. 3.5 days, 5.5 days and 10.4 days. Total N removal was 37.5%, 55.7% and 70.3%, respectively. The 10.4-day E.R.T. trial, however, was evaluated by sequential nutrient removal through the duckweed-minus-fish treatment followed by the duckweed-plus-fish treatment. Therefore, the 70.3% Total N removal was lower than could have been achieved at this retention time due to the abovementioned fish mortalities. Phosphorous removal from duckweed treatments was greatest after 10.4-days E.R.T. (13.6%). Plant uptake was considered the most important mechanism for this P removal since there was no clay substrate in the plastic tanks that could have contributed to P absorption as part of the natural phosphorous cycle. Duckweed inhibited phytoplankton production (therefore reducing T.S.S) and maintained pH close to neutral. DO beneath the duckweed blanket fell to below 1ppm; however, this did not limit plant production. If fish are to be used as part of the duckweed treatment, air-uplifts can be installed that maintain DO levels without disturbing surface waters. Duckweed grown in the treatments doubled its biomass on average every 5.7 days. On a per-surface area basis, 1.23kg/m2 was harvested weekly. Moisture content of duckweed was 92%, equating to a total dry weight harvest of 0.098kg/m2/week. Nutrient analysis of dried duckweed gave an N content of 6.67% and a P content of 1.27%. According to semi-quantitative analyses, harvested duckweed contained no residual elements from the effluent stream that were greater than ANZECC toxicant guidelines proposed for aquaculture. In addition, jade perch, a local aquaculture species, actively consumed and gained weight on harvested duckweed, suggesting potential for large-scale fish production using by-products from the effluent treatment process. This suggests that a duckweed-based system may be one viable option for tertiary treatment of Ayr municipal wastewater. The tertiary detention lagoon proposed by the Burdekin Shire Council, consisting of six bays approximately 290 x 35 metres (x 1.5 metres deep), would be suitable for duckweed culture with minor modification to facilitate the efficient distribution of duckweed plants across the entire available growing surface (such as floating containment grids). The effluent residence time resulting from this proposed configuration (~30 days) should be adequate to recover most effluent nutrients (certainly N) based on the current trial. Duckweed harvest techniques on this scale, however, need to be further investigated. Based on duckweed production in the current trial (1.23kg/m2/week), a weekly harvest of approximately 75 000kg (wet weight) could be expected from the proposed lagoon configuration under full duckweed production. A benefit of the proposed multi-bay lagoon is that full lagoon production of duckweed may not be needed to restore effluent to a desirable standard under the present nutrient load, and duckweed treatment may be restricted to certain bays. Restored effluent could be released without risk of contaminating the receiving waterway with duckweed by evacuating water through an internal standpipe located mid-way in the water column.

Development and testing of allometric equations for estimating above-ground biomass of mixed-species environmental plantings

To quantify the impact that planting indigenous trees and shrubs in mixed communities (environmental plantings) have on net sequestration of carbon and other environmental or commercial benefits, precise and non-biased estimates of biomass are required. Because these plantings consist of several species, estimation of their biomass through allometric relationships is a challenging task. We explored methods to accurately estimate biomass through harvesting 3139 trees and shrubs from 22 plantings, and collating similar datasets from earlier studies, in non-arid (>300mm rainfallyear-1) regions of southern and eastern Australia. Site-and-species specific allometric equations were developed, as were three types of generalised, multi-site, allometric equations based on categories of species and growth-habits: (i) species-specific, (ii) genus and growth-habit, and (iii) universal growth-habit irrespective of genus. Biomass was measured at plot level at eight contrasting sites to test the accuracy of prediction of tonnes dry matter of above-ground biomass per hectare using different classes of allometric equations. A finer-scale analysis tested performance of these at an individual-tree level across a wider range of sites. Although the percentage error in prediction could be high at a given site (up to 45%), it was relatively low (<11%) when generalised allometry-predictions of biomass was used to make regional- or estate-level estimates across a range of sites. Precision, and thus accuracy, increased slightly with the level of specificity of allometry. Inclusion of site-specific factors in generic equations increased efficiency of prediction of above-ground biomass by as much as 8%. Site-and-species-specific equations are the most accurate for site-based predictions. Generic allometric equations developed here, particularly the generic species-specific equations, can be confidently applied to provide regional- or estate-level estimates of above-ground biomass and carbon. © 2013 Elsevier B.V.