Odour Emissions from Tunnel Ventilated Poultry Housing

In Australia, factors such as local planning processes, urban encroachment into rural areas and intensification of the poultry industry have increased the potential for odour and dust nuisance. At present, accurate estimates of odour emissions from mechanically ventilated poultry housing systems do not exist for Australian conditions. This has made the poultry industry vulnerable to unsubstantiated criticism. Recently, the Australian poultry industry have made a significant investment in research to obtain accurate estimates of odour, dust and volatile chemical emission rates from typical poultry housing systems. This paper describes the measurement of odour emissions from tunnel ventilated poultry housing systems in different climatic zones in Queensland and Victoria, Australia (humid sub-tropical and Mediterranean respectively) during two seasons (summer and winter). Samples were collected at defined intervals over typical batch production cycles to define the odour emission profiles. These samples were analysed using dynamic olfactometry according to the Australian Standard 4323.3 to derive the odour concentration values. Ventilation rates were measured concurrently, allowing the calculation of odour emission rates. Odour concentration and emission rates were assessed in terms of ventilation rate, ambient and shed air temperature and relative humidity and litter moisture status. Odour emission rates varied with bird age. Seasonal differences in odour emission rate were also observed.

Influence of concentration, temperature and humidity on the toxicity of phosphine to the strongly phosphine-resistant psocid Liposcelis bostrychophila Badonnel (Psocoptera: Liposcelididae)

BACKGROUND: The psocid Liposcelis bostrychophila Badonnel, is a widespread, significant pest of stored commodities, has developed strong resistance to phosphine, the major grain disinfestant. The aim was to develop effective fumigation protocols to control this resistant pest. RESULTS: Time to population extinction of all life stages (TPE) in days was evaluated at a series of phosphine concentrations and temperatures at two relative humidities. Regression analysis showed that temperature, concentration and relative humidity all contributed significantly to describing TPE (P < 0.001, R2 = 0.95), with temperature being the dominant variable, accounting for 74.4% of the variation. Irrespective of phosphine concentration, TPE was longer at lower temperatures and high humidity (70% RH) and shorter at higher temperatures and low humidity (55% RH). At any concentration of phosphine, a combination of higher temperature and lower humidity provides the shortest fumigation period to control resistant L. bostrychophila. For example, 19 and 11 days of fumigation are required at 15 °C and 70% RH at 0.1 and 1.0 mg L-1 of phosphine respectively, whereas only 4 and 2 days are required at 35 °C and 55% RH for the same respective concentrations. CONCLUSIONS: The developed fumigation protocols will provide industry with flexibility in application of phosphine.

Dietary media for mass rearing of rusty grain beetle, Cryptolestes ferrugineus (Stephens) and flat grain beetle, Cryptolestes pusillus (Schonherr) (Coleoptera: Cucujidae)

We developed a suitable diet for mass rearing of Cryptolestes ferrugineus (Stephens) populations under laboratory conditions. Recently, this pest has developed strong level of resistance to phosphine in Australia, and therefore, a significant amount of research has been directed towards its management. In total, nineteen grain-based diets, containing rolled oats, various combinations of cracked grains and flours of wheat, sorghum, maize and barley were tested. Each diet contained a small proportion of wheat germ (4.5% w/w) and torula yeast (0.5% w/w). Experiments were conducted at fixed temperature and relative humidity regimes of 30 ± 2 °C and 70 ± 2%, respectively, and replicated three times. Adults (n = 40) of a laboratory strain of C. ferrugineus were introduced into each diet, removed after 14 days and total numbers of live adult progeny were recorded. The following diets resulted in highest live progeny production: barley flour (95%) (607.67 ± 11.21) = rolled oats (75%) + cracked sorghum (20%) (597.33 ± 33.79) ≥ wheat flour (47.5%) + barley flour (47.5%) (496.67 ± 52.93) > cracked sorghum (95%) (384.00 ± 60.66). The performance of these four diets was then tested with field-collected populations of C. ferrugineus and Cryptolestes pusillus (Schonherr). The diets based on rolled oats + cracked sorghum, wheat flour + barley flour, and barley flour alone consistently produced highest progeny numbers in field-collected populations of both species, with mean progeny numbers ranging from 359.9 to 478.5. The multiplication of C. pusillus was significantly higher than C. ferrugineus on all four diets. Our findings will help in mass rearing of healthy cultures of C. ferrugineus and C. pusillus that will greatly facilitate laboratory and field research and in particular, in developing management tactics for these species.

An Investigation of Environmental Conditions Experienced During the Life of High Value Wood Components and Products

Australian forest industries have a long history of export trade of a wide range of products from woodchips(for paper manufacturing), sandalwood (essential oils, carving and incense) to high value musical instruments, flooring and outdoor furniture. For the high value group, fluctuating environmental conditions brought on by changes in mperature and relative humidity, can lead to performance problems due to consequential swelling, shrinkage and/or distortion of the wood elements. A survey determined the types of value-added products exported, including species and dimensions packaging used and export markets. Data loggers were installed with shipments to monitor temperature and relative humidity conditions. These data were converted to timber equilibrium moisture content values to provide an indication of the environment that the wood elements would be acclimatising to. The results of the initial survey indicated that primary high value wood export products included guitars, flooring, decking and outdoor furniture. The destination markets were mainly located in the northern hemisphere, particularly the United States of America, China, Hong Kong, Europe including the United Kingdom), Japan, Korea and the Middle East. Other regions importing Australian-made wooden articles were south-east Asia, New Zealand and South Africa. Different timber species have differing rates of swelling and shrinkage, so the types of timber were also recorded during the survey. Results from this work determined that the major species were ash-type eucalypts from south-eastern Australia (commonly referred to in the market as Tasmanian oak), jarrah from Western Australia, spotted gum, hoop pine, white cypress, black butt, brush box and Sydney blue gum from Queensland and New South Wales. The environmental conditions data indicated that microclimates in shipping containers can fluctuate extensively during shipping. Conditions at the time of manufacturing were usually between 10 and 12% equilibrium moisture content, however conditions during shipping could range from 5 (very dry) to 20% (very humid). The packaging systems incorporated were reported to be efficient at protecting the wooden articles from damage during transit. The research highlighted the potential risk for wood components to ‘move’ in response to periods of drier or more humid conditions than those at the time of manufacturing, and the importance of engineering a packaging system that can account for the environmental conditions experienced in shipping containers. Examples of potential dimensional changes in wooden components were calculated based on published unit shrinkage data for key species and the climatic data returned from the logging equipment. The information highlighted the importance of good design to account for possible timber movement during shipping. A timber movement calculator was developed to allow designers to input component species, dimensions, site of manufacture and destination, to see validate their product design. This calculator forms part of the free interactive website www.timbers.com.au.

An investigation of environmental conditions experienced during the life of high-value wood components and products

Australian forest industries have a long history of export trade of a wide range of products from woodchips (for paper manufacturing), sandalwood (essential oils, carving and incense) to high value musical instruments, flooring and outdoor furniture. For the high value group, fluctuating environmental conditions brought on by changes in temperature and relative humidity, can lead to performance problems due to consequential swelling, shrinkage and/or distortion of the wood elements. A survey determined the types of value-added products exported, including species and dimensions packaging used and export markets. Data loggers were installed with shipments to monitor temperature and relative humidity conditions. These data were converted to timber equilibrium moisture content values to provide an indication of the environment that the wood elements would be acclimatising to. The results of the initial survey indicated that primary high value wood export products included guitars, flooring, decking and outdoor furniture. The destination markets were mainly located in the northern hemisphere, particularly the United States of America, China, Hong Kong, Europe (including the United Kingdom), Japan, Korea and the Middle East. Other regions importing Australian-made wooden articles were south-east Asia, New Zealand and South Africa. Different timber species have differing rates of swelling and shrinkage, so the types of timber were also recorded during the survey. Results from this work determined that the major species were ash-type eucalypts from south-eastern Australia (commonly referred to in the market as Tasmanian oak), jarrah from Western Australia, spotted gum, hoop pine, white cypress, black butt, brush box and Sydney blue gum from Queensland and New South Wales. The environmental conditions data indicated that microclimates in shipping containers can fluctuate extensively during shipping. Conditions at the time of manufacturing were usually between 10 and 12% equilibrium moisture content, however conditions during shipping could range from 5 (very dry) to 20% (very humid). The packaging systems incorporated were reported to be efficient at protecting the wooden articles from damage during transit. The research highlighted the potential risk for wood components to ‘move’ in response to periods of drier or more humid conditions than those at the time of manufacturing, and the importance of engineering a packaging system that can account for the environmental conditions experienced in shipping containers. Examples of potential dimensional changes in wooden components were calculated based on published unit shrinkage data for key species and the climatic data returned from the logging equipment. The information highlighted the importance of good design to account for possible timber movement during shipping. A timber movement calculator was developed to allow designers to input component species, dimensions, site of manufacture and destination, to see validate their product design.

Pen studies on the control of cattle tick (Rhipicephalus (Boophilus) microplus) with Metarhizium anisopliae (Sorokin)

Three field trials were conducted over 12 months to assess the pathogenicity of Metarhizium anisopliae to parasitic stages of Rhipicephalus (Boophilus) microplus on dairy heifers under different environmental conditions. Two isolates were selected based on their high optimal growth temperature (30 °C), good spore production characteristics and ability to quickly kill adult engorged ticks in the laboratory. Spores were formulated in an oil emulsion and applied using a motor driven spray unit. Surface temperatures of selected animals were monitored, as were the ambient temperature and relative humidity. Unengorged ticks sampled from each animal immediately after treatment were incubated in the laboratory to assess the efficacy of the formulation and application. Egg production by engorged ticks collected in the first 3 days after treatment was monitored. Side counts of standard adult female ticks were conducted daily, before and after treatment to assess the performance of the fungus against all tick stages on the animals. In each trial the formulation rapidly caused 100% mortality in unengorged ticks that were removed from cattle and cultured in the laboratory. A significant reduction in egg production was recorded for engorged ticks collected in the 3 days post-treatment. However, there was little effect of the formulation on the survival of ticks on cattle, indicating that there is an interaction between the environment of the ticks on the cattle and the biopesticide, which reduces its efficacy against ticks.

Aiming for the management of the small hive beetle, Aethina tumida, using relative humidity and diatomaceous earth

Small hive beetles (SHBs) are a global pest of European honeybee colonies. In the laboratory, the survival of adult SHBs was evaluated in relation to relative humidity (RH = 56, 64, 73, 82 and 96 %) and treatment with diatomaceous earth (DE) across 4 days. Low RH reduced survival. The application of DE reduced survival in addition to RH. Adults treated with corn flour (control) showed no difference in survival from untreated beetles. Scanning electron microscopy images showed no scarification of adult beetle cuticle after exposure to DE; therefore, water loss is likely facilitated through non-abrasive means such as the adsorption of cuticular lipids. The data agree with the hypothesis that DE causes mortality through water loss from treated insects. Egress, ingress, mortality and the egg-laying behaviours of beetles were observed in relation to a popular in-hive trench trap with and without the addition of DE. Traps filled with DE resulted in 100 % mortality of beetles compared with 8.6 % mortality when no DE was present. A simple method for visually determining beetle sex was used and documented.

Effect of drying, storage temperature and air exposure on astaxanthin stability from Haematococcus pluvialis

Astaxanthin is a powerful antioxidant with various health benefits such as prevention of age-related macular degeneration and improvement of the immune system, liver and heart function. To improve the post-harvesting stability of astaxanthin used in food, feed and nutraceutical industries, the biomass of the high astaxanthin producing alga Haematococcus pluvialis was dried by spray- or freeze-drying and under vacuum or air at − 20 °C to 37 °C for 20 weeks. Freeze-drying led to 41 higher astaxanthin recovery compared to commonly-used spray-drying. Low storage temperature (− 20 °C, 4 °C) and vacuum-packing also showed higher astaxanthin stability with as little as 12.3 ± 3.1 degradation during 20 weeks of storage. Cost-benefit analysis showed that freeze-drying followed by vacuum-packed storage at − 20 °C can generate AUD600 higher profit compared to spray-drying from 100 kg H. pluvialis powder. Therefore, freeze-drying can be suggested as a mild and more profitable method for ensuring longer shelf life of astaxanthin from H. pluvialis.

Sources and seasonal dynamics of Alternaria inoculum associated with leaf blotch and fruit spot of apples

Alternaria leaf blotch and fruit spot caused by Alternaria spp. cause annual losses to the Australian apple industry. Control options are limited, mainly due to a lack of understanding of the disease cycle. Therefore, this study aimed to determine potential sources of Alternaria spp. inoculum in the orchard and examine their relative contribution throughout the production season. Leaf residue from the orchard floor, canopy leaves, twigs and buds were collected monthly from three apple orchards for two years and examined for the number of spores on their surface. In addition, the effects of climatic factors on spore production dynamics in each plant part were examined. Although all four plant parts tested contributed to the Alternaria inoculum in the orchard, significant higher numbers of spores were obtained from leaf residue than the other plant parts supporting the hypothesis that overwintering of Alternaria spp. occurred mainly in leaf residue and minimally on twigs and buds. The most significant period of spore production on leaf residue occurred from dormancy until bloom and on canopy leaves and twigs during the fruit growth stage. Temperature was the single most significant factor influencing the amount of Alternaria inoculum and rainfall and relative humidity showed strong associations with temperature influencing the spore production dynamics in Australian orchards. The practical implications of this study include the eradication of leaf residue from the orchard floor and sanitation of the canopy after harvest to remove residual spores from the trees.

Modelling Leaf Production and Crop Development in Maize (Zea mays L.) After Tassel Initiation Under Diverse Conditions of Temperature and Photoperiod

Prediction of the initiation, appearance and emergence of leaves is critically important to the success of simulation models of crop canopy development and some aspects of crop ontogeny. Data on leaf number and crop ontogeny were collected on five cultivars of maize differing widely in maturity and genetic background grown under natural and extended photoperiods, and planted on seven sowing dates from October 1993 to March 1994 at Gatton, South-east Queensland. The same temperature coefficients were established for crop ontogeny before silking, and the rates of leaf initiation, leaf tip appearance and full leaf expansion, the base, optimum and maximum temperatures for each being 8, 34 and 40 degrees C. After silking, the base temperature for ontogeny was 0 degrees C, but the optimum and maximum temperatures remained unchanged. The rates of leaf initiation, appearance of leaf tips and full leaf expansion varied in a relatively narrow range across sowing times and photoperiod treatments, with average values of 0.040 leaves (degrees Cd)-1, 0.021 leaves (degrees Cd)-1, and 0.019 leaves (degrees Cd)-1, respectively. The relationships developed in this study provided satisfactory predictions of leaf number and crop ontogeny (tassel initiation to silking, emergence to silking and silking to physiological maturity) when assessed using independent data from Gatton (South eastern Queensland), Katherine and Douglas Daly (Northern Territory), Walkamin (North Queensland) and Kununurra (Western Australia).

Effects of diet, temperature and photoperiod on development and survival of the bigeyed bug, Geocoris lubra

Bigeyed bugs (Geocoris spp., Hemiptera: Geocoridae) are common predators in Australian agricultural crops yet the development and reproductive biology of Australian geocorids has not been described before. Here we present the effects of diet, temperature and photoperiod on the development and survival of Geocoris lubra Kirkaldy from egg to adult. Nymphal survival of G. lubra reared on live aphids (Aphis gossypii Glover) was very low but improved slightly on a diet of Helicoverpa armigera (Hübner) eggs. Development was faster and nymphal survival improved significantly at 27°C compared with 25°C. Further investigation at 27°C showed photoperiod influenced development time, but not survival of immature G. lubra. Development time was significantly longer at 10L:14D. Fecundity of first generation G. lubra was not affected by photoperiod, although egg viability was greater at 12L:12D.

Weed species richness, density and relative abundance on farms in the subtropical grain region of Australia

Weed management is one of the most important economic and agronomic issues facing farmers in Australia's grain regions. Weed species occurrence and abundance was monitored between 1997 and 2000 on 46 paddocks (sites) across 18 commercial farms located in the Northern Grain Region. The sites generally fell within 4 disjunct regions, from south to north: Liverpool Plains, Moree, Goondiwindi and Kingaroy. While high species richness was found (139 species or species groups), only 8 species occurred in all 4 regions and many (56 species) only occurred at 1 site or region. No species were observed at every site but 7 species (Sonchus spp., Avena spp., Conyza spp., Echinochloa spp., Convolvulus erubescens, Phalaris spp. and Lactuca serriola) were recorded on more than 70% of sites. The average number of species observed within crops after treatment and before harvest was less than 13. Species richness tended to be higher in winter pulse crops, cotton and in fallows, but overall was similar at the different sampling seasons (summer v. winter). Separate species assemblages associated with the Goondiwindi and Kingaroy regions were identified by correspondence analysis but these appeared to form no logical functional group. The species richness and density was generally low, demonstrating that farmers are managing weed populations effectively in both summer and winter cropping phases. Despite the apparent adoption of conservation tillage, an increase in opportunity cropping and the diversity of crops grown (13) there was no obvious effect of management practices on weed species richness or relative abundance. Avena spp. and Sonchus spp. were 2 of the most dominant weeds, particularly in central and southern latitudes of the region; Amaranthus spp. and Raphanus raphanistrum were the most abundant species in the northern part of the region. The ubiquity of these and other species shows that continued vigilance is required to suppress weeds as a management issue.

Germination of Hymenachne amplexicaulis and H. acutigluma under contrasting light, temperature and nitrate regimes

A laboratory experiment compared germination of the invasive exotic grass Hymenachne amplexicaulis (Rudge) Nees and the native H. acutigluma (Steud.) Gilliland. Seeds of both species were exposed to combinations of light (constant dark, alternating dark/light or constant light), temperature (constant or alternating) and nitrate regimes (with or without the addition of KNO3). Three seed lots of H. amplexicaulis (fresh, two adn four months old) and one of H. acutigluma (fresh seed) were tested. A significant temperature x light x nitrate x seed lot interaction occured. At a constant temperature very few seeds of either H. amplexicaulis or H. acutigluma germinated, regardless of the light regime or addition of KNO3. Generally, maximum germination occurred under a combination of alternating temperature, the presence of light (either constant or alternating) and the addition of KNO3. The exception was four month stored H. amplexicaulis seed, which reached maximum germinaction without the need for KNO3. Fresh seed of both H. amplexicaulis and H. acutigluma exhibited similar germination requirements. These findings suggest that conditions that buffer seeds from light and/or temperature fluctuations could reduce germination and possibly extend the life of seed banks of both H. amplexicaulis and H. acutigluma. Conversely, for land managers trying to control the exotic H. amplexicaulis, activities that create more favourable conditions for germination may help deplete seed banks faster.

Temperature and Salinity Tolerances of the Tropical Spiny Lobster, Panulirus ornatus

Interest in the development of aquaculture of the tropical spiny lobster, Panulirus ornatus, has increased markedly over the past 10 yr because of strong market demand and high prices. In Australia, economic conditions will necessitate that a semi-intensive approach be taken, possibly involving managed environmental conditions. Identification of optimal temperature and salinity levels will be necessary, and therefore two experiments were performed to examine these two parameters. Juvenile lobsters were grown in tanks at five temperatures (19, 22, 25, 28 and 31 C). Growth was significantly affected by temperature (P < 0.01), and maximal growth occurred at 25-31 C. Examination of the temperature effect on molt increment and intermolt period indicated that 27 C was the optimal temperature, at which molt increment was greatest and intermolt period the least. Temperature also had a significant (P < 0.01) positive effect on apparent feed intake (AFI). Juvenile lobsters were also exposed to four different salinities (20, 25, 30 and 35 ppt) over a period of 91 d. Significant differences (P < 0.01) were apparent for both survival and growth. Lowest survival occurred at 35 ppt which may be attributable to higher cannibalism at that salinity. Growth was highest at 35 ppt and progressively less at lower salinities. Although full marine salinity (35 ppt) will generate best performance of P. ornatus, its capacity to tolerate reduced salinity will provide greater opportunity to develop commercial aquaculture.

Modelling the distribution and relative abundance of feral camels in the Northern Territory using count data

The objectives of this study were to predict the potential distribution, relative abundance and probability of habitat use by feral camels in southern Northern Territory. Aerial survey data were used to model habitat association. The characteristics of ‘used’ (where camels were observed) v. ‘unused’ (pseudo-absence) sites were compared. Habitat association and abundance were modelled using generalised additive model (GAM) methods. The models predicted habitat suitability and the relative abundance of camels in southern Northern Territory. The habitat suitability maps derived in the present study indicate that camels have suitable habitat in most areas of southern Northern Territory. The index of abundance model identified areas of relatively high camel abundance. Identifying preferred habitats and areas of high abundance can help focus control efforts.