Wood properties and knot occlusion of plantation grown Eucalyptus dunnii and Corymbia citriodora subsp. variegata in a pruning and thinning experiment.

A 2 × 2 factorial combination of thinned or unthinned, and pruned or unpruned 11-year-old Eucalyptus dunnii (DWG) and 12-year-old Corymbia citriodora subsp. variegata (CCV) was destructively sampled to provide 60 trees in total per species. Two 1.4 m long billets were cut from each tree and were rotary veneered in a spindleless lathe down to a 45 mm diameter core to expose knots which were classified as either alive, partially occluded or fully occluded. Non-destructive evaluation of a wider range of thinning treatments available in these trials was undertaken with Pilodyn and Fakopp tools. Disc samples were also taken for basic density and modulus of elasticity. Differences between treatments for all wood property assessments were generally small and not significantly different.Thinning and pruning had little effect on the stem diameter growth required to achieve occlusion, therefore occlusion would be more rapid after thinning due to more rapid stem diameter growth. The difference between the treatments of greatest management interest, thinned and pruned (T&P) and unthinned and unpruned (UT&UP) were small. The production of higher value clear wood produced after all knots had occluded, measured as the average stem diameter growth over occlusion of the three outermost knots, was approximately 2 centimetres diameter. Two of the treatments can be ruled out as viable management alternatives: (i) the effect of thinning without pruning (T&UP) is clear, leading to a large inner core of stem wood containing knots (large knotty core diameter) and (ii) pruning without thinning (UT&P) results in a small knotty core diameter, however the tree and therefore log diameters are also small.

The effect of initial spacing and thinning on wood quality and graded sawn recovery of mature Caribbean pine grown in Queensland.

A mature Caribbean pine (Pinus caribaea var. hondurensis) silviculture experiment provided initial square spacing treatments of 1.8 m2, 2.4 m2, 3.0 m2 and 3.6 m2 (equal to 3088, 1737, 1111 and 772 stems/ha) that were thinned at age 10 years to 600, 400 and 200 stems/ha, retaining an unthinned control for each initial spacing. The trial was destructively sampled at age of 28 years and discs taken along 8 various stem heights were analysed for variation in basic density and SilviScan wood properties. In addition, the logs from ten stocking × thinning treatments were processed in a sawing study. Results indicate thinning effects were generally more pronounced than initial spacing effects. Fast growing trees produced wood with significantly higher average wood densities and higher average stiffness values. Detailed SilviScan densitometry results obtained radially and at various stem heights enabled construction of tree maps for wood properties, providing insights into the variation in juvenile to mature wood proportion across the initial and post-thinning stocking treatments studied. Dried dressed recovery was strongly related to tree size, and log value decreased consistently from butt to top logs across all treatments. The estimated value per hectare was highest in unthinned plots due to values being multiplied by high stem numbers per hectare. However, a complete economic analysis considering all cost structures is required to investigate the optimal silviculture to maximise economic returns to growers and processors. Improved understanding of the relationship between initial spacing, post-thinning stocking and wood and end-product quality should help to customize future forest management strategies required to produce better quality wood and wood products.

Structural Veneer Based Composite Products from Hardwood Thinning - Part II: Testing of Hollow Utility Poles

Australian utility pole network is aging and reaching its end of life, with 70% of the 5 million poles currently in-service nationally installed within the 20 years following the end of World War II. The estimated investment required for the replacement or remedial maintenance of the aging 3.5 millions poles is as high as 1.75 billion dollars. Additionally, an estimated 21,700 high-durability new poles are required each year, representing further investment of 13.5 million dollars per year. Yet, agreements which progressively phase out logging of native forests around Australia have been signed, giving the industry about 25 years to make the transition from Crown native forests to plantations and private forests. As utility poles were traditionally cut from native forest hardwood species, finding solutions to source new poles currently presents a challenge. This paper presents tests on Veneer Based Composite hardwood hollow utility poles manufactured from Gympie messmate (Eucalyptus cloeziana) plantation thinning. Small diameter poles of nominal 115 mm internal diameter and 15 mm wall-thickness were manufactured in two half-poles butt jointed together, using 9 veneers per halfpole. The poles were tested in bending and shear, and experimental test results are presented. The mechanical performance of the hollow poles is discussed and compared to hardwood poles cut from mature trees and of similar size. Future research and different options for improving the current concept are proposed in order to provide a more reliable and cost effective technical solution to the current shortage of utility poles. © RILEM 2014.

Structural Veneer Based Composite Products from Hardwood Thinning - Part I: Background and Manufacturing

In Australia, plantation forests have increased in area by around 50% in the last 10 years. While this expansion has seen a modest 8% increase for softwoods, hardwood plantations have dramatically increased by over 150%. Hardwood plantations grown for high quality sawn timber are slow to mature, with a crop rotation time potentially reaching 35 years. With this long lead-time, each year the risk from fire, pests and adverse weather events dramatically increases, while not translating into substantially higher financial returns to the grower. To justify continued expansion of Australia's current hardwood plantation estate, it is becoming necessary to develop higher value end-uses for both pulpwood and smaller 'sawlog' resources. The use of the low commercial value stems currently culled during thinning appears to be a necessary option to improve the industry profitability and win new markets. This paper provides background information on Australian forests and plantations and gives an overview of potential uses of Australian hardwood plantation thinning logs, as their mechanical properties. More specifically, this paper reports on the development of structural Veneer Based Composite (VBC) products from hardwood plantation thinning logs, taking advantage of a recent technology developed to optimise the processing of this resource. The process used to manufacture a range of hollow-form veneer laminated structural products is presented and the mechanical characteristics of these products are investigated in the companion paper. The market applications and future opportunities for the proposed products are also discussed, as potential benefits to the timber industry. © RILEM 2014.

Performance of seven hardwood species underplanted to Pinus elliottii in south-east Queensland

Seven hardwood species were tested as underplants under Pinus elliottii plantations on the coastal lowlands of south-east Queensland. The species tested were: Flindersia brayleyana (F. Muell) (Queensland maple), F. australis (R. Br.), (crow's ash), Swietenia macrophylla (King) (American mahogany), Grevillea robusta (A. cunn) (southern silky oak), Elaeocarpus grandis (F. Muell) (silver quandong), F. ifflaiana (F. Meull) (Cairns hickory) and Ceratopetalum apetalum (D. Don) (coachwood). Most species (except E. grandis) established successfully but slowly. Underplants suffered 9-16% mortality during thinning of the overstorey. By 2004 when aged c. 38 years, four underplanted species; F. brayleyana, S. macrophylla, F. ifflaiana and E. grandis, had attained predominant heights of 20 m and mean diameter at breast height of 25 cm or better. The presence of underplants increased total site productivity by up to 23% and did not have any detrimental effect on the development of the overwood.This experiment has demonstrated that some rainforest species will survive and grow healthily as underplants in exotic pine plantations plus produce small merchantable logs within a 38 year rotation. The results also indicated the importance of correct species selection if an underplanting option is to be pursued as some species have been a complete failure (notably G. robusta).

Sustainable native forest management. Case studies in managing private native forest in southeast Queensland.

The introduction describes productive forest in Queensland and summaries the principles of native forest management that achieve optimum productivity. Case study 1 deals with thinning an even-aged regrowth forest. It shows how thinning the stand actively manages the future composition and structure to improve productivity in the best stems and increase the commercial value of the next harvest. Case study 2 describes restoring productivity in a high-graded spotted gum - ironbark forest. It shows that defective and non-saleable trees should be removed so they do not repress the future stand; and that regeneration should be thinned, retaining the best trees in adequate growing space. Case study 3 discusses on-farm value adding for hardwood forests. It shows how long-term viability and maximum productivity and returns depend on the best management practices and knowing how to obtain the best returns from a range of forest products. Case study 4 examines integrated harvesting in a eucalypt forest. It shows how integrating the harvest enables the full range of timber products are harvested and sold for their maximum value while reducing the amount of waste.

Woody plant responses to various clearing strategies imposed on a poplar box (Eucalyptus populnea) community at Dingo in central Queensland

The efficacy of individual tree treatment (stem-injection), aerially applied root-absorbed herbicide and mechanical felling (with and without subsequent fire) in controlling woody plants was compared in a poplar box (Eucalyptus populnea) woodland community in central Queensland, Australia. All treatments reduced woody plant populations and basal area relative to the untreated control. Chemical control and 'mechanical felling plus fire' treatments were equally effective in reducing woody plant basal area 7 years after the treatments were imposed. However, mechanical felling alone was less effective. There was a clear tendency for the scattered tree (80% thinning) treatment to recover woody plant basal area towards pre-treatment levels faster than other clearing strategies, although this response was not significantly different from 20% clump retention and mechanical felling (without burning) treatments.

Research note: poplar box (Eucalyptus populnea) growth rates in thinned and intact woodlands in central Queensland

A 19-year data set, which highlights the rapid growth rate in basal area of trees in thinned plots compared with unthinned controls, is presented. These results support the contention that, following tree thinning, basal area of retained trees will increase more rapidly than that of trees on unthinned areas. Indications are that pre-thinning levels in tree basal area will again be reached before the cost of treatment can be recouped by increased pasture and livestock production.

Tree growth relationships and silvicultural tools to assist stand management in private native spotted gum dominant forests in Queensland and northern New South Wales.

Spotted gum dominant forests occur from Cooktown in northern Queensland (Qld) to Orbost in Victoria (Boland et al. 2006) and these forests are commercially very important with spotted gum the most commonly harvested hardwood timber in Qld and one of the most important in New South Wales (NSW). Spotted gum has a wide range of end uses from solid wood products through to power transmission poles and generally has excellent sawing and timber qualities (Hopewell 2004). The private native forest resource in southern Qld and northern NSW is a critical component of the hardwood timber industry (Anon 2005, Timber Qld 2006) and currently half or more of the native forest timber resource harvested in northern NSW and Qld is sourced from private land. However, in many cases productivity on private lands is well below what could be achieved with appropriate silvicultural management. This project provides silvicultural management tools to assist extension staff, land owners and managers in the south east Qld and north eastern NSW regions. The intent was that this would lead to improvement of the productivity of the private estate through implementation of appropriate management. The other intention of this project was to implement a number of silvicultural experiments and demonstration sites to provide data on growth rates of managed and unmanaged forests so that landholders can make informed decisions on the future management of their forests. To assist forest managers and improve the ability to predict forest productivity in the private resource, the project has developed: • A set of spotted gum specific silvicultural guidelines for timber production on private land that cover both silvicultural treatment and harvesting. The guidelines were developed for extension officers and property owners. • A simple decision support tool, referred to as the spotted gum productivity assessment tool (SPAT), that allows an estimation of: 1. Tree growth productivity on specific sites. Estimation is based on the analysis of site and growth data collected from a large number of yield and experimental plots on Crown land across a wide range of spotted gum forest types. Growth algorithms were developed using tree growth and site data and the algorithms were used to formulate basic economic predictors. 2. Pasture development under a range of tree stockings and the expected livestock carrying capacity at nominated tree stockings for a particular area. 3. Above-ground tree biomass and carbon stored in trees. •A series of experiments in spotted gum forests on private lands across the study area to quantify growth and to provide measures of the effect of silvicultural thinning and different agro-forestry regimes. The adoption and use of these tools by farm forestry extension officers and private land holders in both field operations and in training exercises will, over time, improve the commercial management of spotted gum forests for both timber and grazing. Future measurement of the experimental sites at ages five, 10 and 15 years will provide longer term data on the effects of various stocking rates and thinning regimes and facilitate modification and improvement of these silvicultural prescriptions.

Characterisation of sweetpotato from Papua New Guinea and Australia: Physicochemical, pasting and gelatinisation properties.

The physicochemical and functional properties of flours from 25 Papua New Guinean and Australian sweetpotato cultivars were evaluated. The cultivars (white-, orange-, cream-, and purple-fleshed, and with dry matter, from 15 to 28 g/100 g), were obovate, oblong, elliptic, curved, irregular in shape, and essentially thin-cortexed (1-2 mm). Flour yield was less than 90 g/100 g solids, while starch, protein, amylose, water absorption and solubility indices, as well as total sugars, varied significantly (p < 0.05). Potassium, sodium, calcium, and phosphorus were the major minerals measured, and there were differences in the pasting properties, which showed four classes of shear-thinning and shear-thickening behaviours. Differential scanning calorimetry showed single-stage gelatinisation behaviour, with cultivar-dependent temperatures (61-84 degrees C) and enthalpies (12-27 J/g dry starch). Oval-, round- and angular-shaped granules were observed with a scanning electron microscope, while X-ray diffraction revealed an A-type diffraction pattern in the cultivars, with about 30% crystallinity. This study shows a wide range of sweetpotato properties, reported for the first time.

Rotary veneering of plantation-grown spotted gum (Corymbia citriodora subsp. variegata) and Dunn's white gum (Eucalyptus dunnii)

This report evaluates the wood and veneer properties of plantation-grown spotted gum (Corymbia citriodora subsp. variegata, or CCV) and Dunn's white gum (Eucalyptus dunnii), grown at different stockings, in thinning trials near Ellangowan in north-east New South Wales (mean annual rainfall 1050 mm) and Kingaroy in south-east Queensland (mean annual rainfall 873 mm). Thinning trials were established at age seven years. Both species showed a significant increase in stem diameter growth of the dominant trees in response to thinning. At age 10 years, trees from the unthinned (950–1270 stems ha-1) and 300 stems ha-1 treatments were selected for veneering. Five dominant trees were felled from each combination of species x sites x thinning treatment. Diameter at breast height over bark of the selected trees ranged from 20 cm to 27 cm at Ellangowan, and 19 cm to 26 cm at Kingaroy. From each tree, 1.5 m long billets were removed at two positions: a butt billet from 0.3–1.8 m above ground and a top billet from approximately 5.5–7.0 m. Log end splitting was assessed 24 hours after harvesting and again after steaming, approximately four days after harvesting. Disks from just above both billets were collected for assessment of wood properties. Billets were peeled on a spindleless veneer lathe to produce a full veneer ribbon with a target green thickness of 2.8 to 3.0 mm. The 1.55 m wide (tangential dimension) veneer sheets were dried and graded according to AS/NZ Standard 2269:2008, which describes four veneer grades. Veneer samples taken along the length of the veneer ribbon, at regular intervals of 1.55 m, were tested for stiffness, shrinkage and density. Veneer length measurements were used to calculate the radial distance of each sample from the central axis of the billet. Overall veneer gross recoveries ranged from 50% to 70%. They were significantly lower at the Kingaroy site, for both species. The veneer recoveries achieved were 2–3 times higher than typical green off saw recoveries from small plantation hardwood logs of similar diameter. Most of the veneer recovered was classified as D-grade. CCV trees from the Ellangowan site yielded up to 38% of the better C-grade and higher grade veneers. The main limiting factors that prevented veneer from meeting higher grades were the presence of kino defects and encased knots. Splits in E. dunnii veneer also contributed to reduced grade quality. Log end splits were higher for E. dunnii than for CCV, and logs from Ellangowan exhibited more severe splitting. Split index was generally higher for top than for butt billets. Split index was strongly correlated with the average veneer grade from corresponding billets. The Ellangowan site, where rainfall was higher and trees grew faster, yielded significantly denser and stiffer veneers than did the drier sites near Kingaroy, where tree growth was slower. The difference was more pronounced for E. dunnii than for CCV. Differences in measured wood properties between thinned and unthinned treatments were generally small and not significant. On average, 10% of billet volume was lost during the peeling rounding-up process. Much of the wood laid down following thinning was removed during rounding-up, meaning the effect of thinning on veneer properties could not be effectively assessed. CCV was confirmed as having high veneer density and very good veneer stiffness, exceeding 15 GPa, making it very suitable for structural products. E. dunnii also demonstrated good potential as a useful structural plywood resource, achieving stiffness above 10 GPa. Veneer stiffness and density in CCV increased from pith to bark at both sites, while for E. dunnii there was a radial increase in these properties at the Ellangowan site only. At the drier Kingaroy site, veneer stiffness and density declined from mid-radius to the log periphery. This may be associated with prolonged drought from 2005 to 2009, corresponding to the later years of tree growth at the Kingaroy site. CCV appeared to be less sensitive to drought conditions. Standing tree acoustic velocity, determined by the Fakopp time-of-flight method, provided a reliable prediction of average veneer stiffness for both species (R2=0.78 for CCV and R2=0.90 for E. dunnii) suggesting that the Fakopp method may be a useful indicator of tree and stand quality, in terms of veneer stiffness in standing trees.

Processing small diameter logs from sub-tropical species

Small spindleless veneer lathe technology was used to produce veneer sheets as an alternative processing option to optimise the use of small log plantation resource. Thinned (300 spha) and unthinned control (1000 spha) plantings of 10.5-year-old Corymbia citriodora ssp. variegata (CCV) and E. dunnii (Dunn’s white gum) grown in two contrasting sites from climatic regions with large annual rainfall differences were studied. Overall veneer gross recoveries ranged from 50% to 70%, which were up to 3 times higher than typical sawn green-off saw recoveries from small plantation hardwood logs of similar diameter. Major limiting factors preventing veneer from meeting higher grades were the presence of kino defects and encased knots. Splits in E. dunnii veneer also contributed to reduced grade quality. Differences between two thinning treatments for veneer properties and grade recovery were generally small. There was significant evidence of site and species differences on veneer quality. The good quality site with higher rainfall in northern New South Wales produced denser and stiffer veneers with higher grade recoveries. CCV is a superior structural veneer species with high wood density and hardness as well as very good veneer stiffness exceeding 15,000 MPa but Dunn’s white gum has also demonstrated good potential as a useful structural plywood resource. Results indicate that relatively high veneer recoveries were achieved for the sub-tropical plantation hardwoods combined with very superior mechanical properties which suggest that veneer production have suitable attributes for a range of engineered wood products including plywood and laminated veneer lumber.

Innovative new production systems for low-chill stonefruit in Australia and South-East Asia: a review

Fruit size and quality are major problems in early-season stonefruit cultivars grown in Australia and South-East Asia. In Australia, Thailand and Vietnam, new training and trellising systems are being developed to improve yield and fruit quality. Australian trials found that new training systems, such as the Open Tatura system, are more productive compared with standard vase-trained trees. We established new crop-loading indices for low-chill stonefruit to provide a guide for optimum fruit thinning based on fruit number per canopy surface and butt cross sectional area. Best management practices were developed for low-chill stonefruit cultivation using growth retardants, optimizing leaf nitrogen concentrations and controlling rates and timing of irrigation. Regulated deficit irrigation (RDI) improved fruit sugar concentrations by restricting water application during stage II of fruit growth. New pest and disease control measures are also being developed using a new generation of fruit fly baits. Soft insecticides such as (Spinosad) are used at significantly lower concentrations and have lower mammalian toxicity than the organophosphates currently registered in Australia. In addition, fruit fly exclusion netting effectively eliminated fruit fly and many other insect pests from the orchard with no increase in diseases. This netting system increased sugar concentrations of peach and nectarine by as much as 30%. Economic analyses showed that the break-even point can be reduced from 12 to 6 years Open Tatura trellising and exclusion netting.

Veneer based composite hollow utility poles manufactured from hardwood plantation thinned trees

Australia’s utility pole network is aging and approaching its end of life. It is estimated that 70% of the 5 million poles currently in-service nationally were installed within the 20 years following the end of World War II and require replacement or remedial maintenance. Additionally, an estimated 21,700 high-durability new poles are required each year to support the expansion of the energy network. Utility poles were traditionally cut from native forest hardwood species. However, due to agreements which progressively phase out logging of native forests around Australia, finding new sources for utility poles presents a challenge. This paper presents the development of veneer based composite hardwood hollow utility poles manufactured from mid-rotation Gympie messmate (Eucalyptus cloeziana) plantation thinned trees (also referred to as “thinning”), as an alternative to solid hardwood poles. The incentives behind the project and benefits of the proposed products are introduced in the paper. Small diameter poles, of nominal 115 mm internal diameter and 15 mm wall-thickness, were manufactured in two half-poles butt jointed together, using 9 hardwood veneers per half-pole. The poles were tested in bending and shear, and experimental test results are presented. The mechanical performance of the hollow poles is discussed and compared to hardwood poles sourced from mature trees and of similar size. Additionally, the required dimensions of the proposed hollow pole to replace actual solid poles are estimated. Results show that the proposed product represents a viable technical solution to the current shortage of utility poles. Future research and different options for improving the current concept are proposed in order to provide a more reliable and cost effective product for structural and architectural applications in general.

Variation in rotary veneer recovery from australian plantation Eucalyptus globulus and Eucalyptus nitens

The processing of Australian plantation-grown Eucalyptus globulus and E. nitens into rotary veneer was shown to produce acceptable recoveries. Three plantation sites for each species were sampled. Silvicultural treatments (thinning and pruning) and growing environments varied between sites. Graded veneer recoveries were dominated by D-grade veneer across all six sites. Variation between the E. nitens sites was evident, with recoveries differing between sites reflecting silvicultural treatments. However, only minimal variation in recovery was shown between the E. globulus sites. The presence of similar levels of defects across all E. globulus sites indicates that the intensive silvicultural management at one site studied was not effective in the production of clear wood, and may possibly have adversely affected grade recovery. Veneer value analysis demonstrated only minimal differences between E. globulus sites. More variation was observed in the E. nitens value analysis; however, intensive silvicultural management implemented did not necessarily result in higher veneer value.