Mass transfer properties (permeability and mass diffusivity) of four Australian hardwood species

Characterisation of mass transfer properties was achieved in the longitudinal, radial, and tangential directions for four Australian hardwood species: spotted gum, blackbutt, jarrah and messmate. Measurement of mass transfer properties for these species was necessary to complement current vacuum drying modelling research. Water-vapour diffusivity was determined in steady state using a specific vapometer. Permeability values of some species and material directions were extremely low and undetectable by the mass flow meter device. Hence, a custom system based on volume evolution was conceived to determine very low, previously unpublished, wood permeability values. Mass diffusivity and permeability were lowest for spotted gum and highest for messmate. Except for messmate, in the radial direction, the four species measured were less permeable in all directions than the lowest published figures, demonstrating the high impermeability of Australian hardwoods and partly accounting for their relatively slow drying rates. Premeability, water-vapour diffusivity, and associated anisotropic ratio data obtained for messmate were extreme or did not follow typical trends and is consequently the most difficult of the four woods to dry in terms of collapse and checkinng degradation.

Evaluation of super-heated steam vacuum drying viability and development of a predictive drying model for four Australian hardwood species.

The results of drying trials show that vacuum drying produces material of the same or better quality than is currently being produced by conventional methods within 41 to 66 % of the drying time, depending on the species. Economic analysis indicates positive or negative results depending on the species and the size of drying operation. Definite economic benefits exist by vacuum drying over conventional drying for all operation sizes, in terms of drying quality, time and economic viability, for E. marginata and E. pilularis. The same applies for vacuum drying C. citriodora and E. obliqua in larger drying operations (kiln capacity 50 m3 or above), but not for smaller operations at this stage. Further schedule refinement has the ability to reduce drying times further and may improve the vacuum drying viability of the latter species in smaller operations.

Germination and hardseededness in desmanthus

The mechanisms and control of hardseededness in the 3 Australian cultivars of the genus Desmanthus were investigated in a series of experiments in which the effects of various seedsoftening treatments, particularly boiling water, were measured. Desmanthus seed is predominantly hard, only defective seeds being normally otherwise. As it has only very brief, early embryo dormancy, hardseededness is the only serious barrier to germination. Seed is most readily softened through rupture of the palisade at the lens (strophiole). The lens is of a typically mimosaceous type which is readily ruptured by immersion in boiling water or less readily by application of pressure to adjacent parts of the testa. Ruptures may consist only of separation of the palisade from underlying tissue, which alone does not confer permeability; mostly they also result in fractures to the palisade that then render seeds irreversibly permeable. The palisade becomes reflective as it separates, which allows the event to be witnessed at the moment of separation if suitable pressure is applied to the testa of an individual seed while it is viewed under magnification. Brief (4–10 seconds) immersion of highquality seed in boiling water consistently softened a high proportion of seeds without causing serious damage. Extending the duration of immersion led to a progressive increase in the proportion of seed deaths. Neither previous boiling water treatment nor scarification damage to the testa materially affected results of treatment, but immature and small seeds behaved differently, being more vulnerable to damage than mature seed, and less likely to undergo lens rupture. Adaptation of boiling water treatment to farm-scale seed handling was simple and reliable. Commercial treatment of seed by an alternative method suitable for greater bulks and consisting of passage through a rice-whitener was checked and found to be successful through a combination of gentle scarification and lens rupture, both attributable to the numerous minor impacts of the process. Percentage emergence of seedlings from soil in the greenhouse closely followed percentage laboratory germination, except when inferior seed grades were included in the comparison, when emergence was poor. Very little seed softened in soil. Already-permeable seed either germinated rapidly or died, while buried hard seed mostly remained hard and viable even more than a year after sowing.

In vitro Induction of Banana Autotetraploids by Colchicine Treatment of Micropropagated Diploids

Alternative breeding strategies, based on colchicine-induced autotetraploids, have been proposed as a means of introducing disease resistance into banana breeding programs. This paper describes techniques for the in vitro induction of banana autotetraploids by the use of colchicine on cultured explants. The technique can be readily applied and large numbers of autotetraploids produced. The optimum treatment involved immersing shoot tips in a 0.5% w/v colchicine solution for 2 h under aseptic conditions. Dimethyl sulfoxide (DMSO) was applied with the colchicine treatments to increase cell permeability and so absorption of colchicine, resulting in the optimum treatment unchanged at 0.5% colchicine, but including the addition of 2% v/v DMSO. Of the shoot tips treated over 30% were induced to the autotetraploid level. Methods for in vitro selection of induced tetraploids from treated diploid plantlets were also developed. Tetraploid plants were more robust with thicker pseudostems, roots and broader leaves than diploids and they could be selected on these morphological characteristics. Mean stornatal lengths of diploid banana plants growing in vitro were significantly smaller (16.0 pm) than the tetraploids (26.9pm) and were used as a more reliable indicator of ploidy than morphological criteria alone. A root tip squash technique using carbol fuchsin was developed for positive confirmation of ploidy change by chromosome counts. Although chimerism and reversion to the diploid form occurred, it was not considered a problem because of the large number of autotetraploids induced. Stable autotetraploids were recovered and established in the field and were characterised by their large, drooping leaves and thick pseudostems. They have retained these characteristics for more than 3 years in the field.

Essential Oil Composition of Diploid and Tetraploid Clones of Ginger (Zingiber officinale Roscoe) Grown in Australia

Ginger oil, obtained by steam distillation of the rhizome of Zingiber officinale Roscoe, is used in the beverage and fragrance industries. Ginger oil displays considerable compositional diversity, but is typically characterized by a high content of sesquiterpene hydrocarbons, including zingiberene, arcurcumene, â-bisabolene, and â-sesquiphellandrene. Australian ginger oil has a reputation for possessing a particular “lemony” aroma, due to its high content of the isomers neral and geranial, often collectively referred to as citral. Fresh rhizomes of 17 clones of Australian ginger, including commercial cultivars and experimental tetraploid clones, were steam distilled 7 weeks post-harvest, and the resulting oils were analyzed by GC-MS. The essential oils of 16 of the 17 clones, including the tetraploid clones and their parent cultivar, were found to be of substantially similar composition. These oils were characterized by very high citral levels (51-71%) and relatively low levels of the sesquiterpene hydrocarbons typical of ginger oil. The citral levels of most of these oils exceeded those previously reported for ginger oils. The neral-to-geranial ratio was shown to be remarkably constant (0.61 ( 0.01) across all 17 clones. One clone, the cultivar “Jamaican”, yielded oil with a substantially different composition, lower citral content and higher levels of sesquiterpene hydrocarbons. Because this cultivar also contains significantly higher concentrations of pungent gingerols, it possesses unique aroma and flavor characteristics, which should be of commercial interest.

Improving sheep feedlot management

This paper summarise six studies undertaken by the Sheep CRC to elucidate certain aspects of confinement feeding of sheep. A review of confinement feeding highlighted the variability of growth rate and feed conversion of sheep and revealed that little is known about the use of sorghum for feeding sheep. The review indicated that the main factors responsible for variation of growth rate and feed conversion were adaptation to grain and feeding system, including the preparation and presentation of feed. The importance of social and physiological adaptation to grain feeding was confirmed. Factors identified as responsible for safe induction and uniform growth rates included prior exposure to grain as lambs, gradual introduction of grain and, when concentrate was provided ad libitum from the first day, the use of either virginiamycin, a pelleted feed, a total mixed ration or a step-wise increase of high-starch grain components. Separate feeding of hay and grain resulted in performance comparable with that of a pelleted diet and that of a total mixed ration. Sorghum-based concentrate diets resulted in growth rates and carcase weights similar to that for winter cereal grains or pellets. Steam flaking or expanding of sorghum had no significant effect on growth rates or carcase weights. These results can be used to determine the profitability of various feedlotting options.

Activation of several key components of the epidermal differentiation pathway in cattle following infestation with the cattle tick, Rhipicephalus (Boophilus) microplus.

The cattle tick, Rhipicephalus (Boophilus) microplus, and the diseases it transmits pose a persistent threat to tropical beef production. Genetic selection of host resistance has become the method of choice for non-chemical control of cattle tick. Previous studies have suggested that larval stages are most susceptible to host resistance mechanisms. To gain insights into the molecular basis of host resistance that occurs during R. microplus attachment, we assessed the abundance of proteins (by isobaric tag for relative and absolute quantitation (iTRAQ) and Western blot analyses) and mRNAs (by quantitative reverse transcription PCR (qRT-PCR)) in skin adjacent to tick bite sites from high tick-resistant (HR) and low tick-resistant (LR) Belmont Red cattle following challenge with cattle tick. We showed substantially higher expression of the basal epidermal keratins KRT5 and KRT14, the lipid processing protein, lipocalin 9 (LCN9), the epidermal barrier catalysing enzyme transglutaminase 1 (TGM1), and the transcriptional regulator B lymphocyte-induced maturation protein 1 (Blimp1) in HR skin. Our data reveals the essential role of the epidermal permeability barrier in conferring greater resistance of cattle to tick infestation, and suggest that the physical structure of the epidermal layers of the skin may represent the first line of defence against ectoparasite invasion. Crown Copyright. © Australian Society for Parasitology Inc.

Commercial products from bio-active extractives in cypress milling residues.

Extractive components obtained from milling residues of white cypress were studied for chemical identity and bioactivity with a view to developing a commercial use for these components, thus increasing the value of the residues and improving the economics of cypress sawn wood production. Extracts obtained by solvent or steam extraction techniques from cypress sawdust were each fractionated by a range of techniques into groups of similar compounds. Crude extracts and fractions were screened against a range of agricultural pests and diseases, including two fungi, subterranean termites, fruit spotting bugs, two-spotted mites, thrips, heliothis, banana scab moths, silverleaf whiteflies, cattle tick adults and larvae, and ruminant gastrointestinal nematodes. Additional screening was undertaken where encouraging results were achieved, for two-spotted mites, thrips, silverleaf whiteflies, cattle tick adults and ruminant gastrointestinal nematodes. After considering degrees of efficacy against, and economic importance of, the agricultural pests, and likely production costs of extracts and fractions, the crude extract (oil) produced by steam distillation was chosen for further study against silverleaf whitefly. A useful degree of control was achievable when this oil was applied to tomato or eggplant at 0.1%, with much less harmful effects on a beneficial insect. Activity of the oil against silverleaf whitefly was undiminished 3.5 years after it was generated. There was little benefit from supplementing the extract with co-formulated paraffinic oil. From the steam distilled oil, fifty-five compounds were characterised, thirty-five compounds representing 92.478 % of the oil, with guaiol (20.8%) and citronellic acid (15.9%) most abundant. These two compounds, and a group of oxygenated compounds containing bulnesol and a range of eudesmols, were found to account for most of the activity against silverleaf whitefly. This application was recommended for first progression to commercialisation.

Probiotic Bacillus amyloliquefaciens Strain H57 Improves the Performance of Pregnant and Lactating Ewes Fed a Diet Based on Palm Kernel Meal

Probiotic supplements are single or mixed strain cultures of live microorganisms that benefit the host by improving the properties of the indigenous microflora (Seo et al 2010). In a pilot study at the University of Queensland, Norton et al (2008) found that Bacillus amyloliquefaciens Strain H57 (H57), primarily investigated as an inoculum to make high-quality hay, improved feed intake and nitrogen utilisation over several weeks in pregnant ewes. The purpose of the following study was to further challenge the potential of H57 -to show it survives the steam-pelleting process, and that it improves the performance of ewes fed pellets based on an agro-industrial by-product with a reputation for poor palatability, palm kernel meal (PKM), (McNeill 2013). Thirty-two first-parity White Dorper ewes (day 37 of pregnancy, mean liveweight = 47.3 kg, mean age = 15 months) were inducted into individual pens in the animal house at the University of Queensland, Gatton. They were adjusted onto PKM-based pellets (g/kg drymatter (DM): PKM, 408; sorghum, 430; chick pea hulls, 103; minerals and vitamins; Crude protein, 128; ME: 11.1MJ/kg DM) until day 89 of pregnancy and thereafter fed a predominately pelleted diet incorporating with or without H57 spores (10 9 colony forming units (cfu)/kg pellet, as fed), plus 100g/ewe/day oaten chaff, until day 7 of lactation. From day 7 to 20 of lactation the pelleted component of the diet was steadily reduced to be replaced by a 50:50 mix of lucerne: oaten chaff, fed ad libitum, plus 100g/ewe/day of ground sorghum grain with or without H57 (10 9 cfu/ewe/day). The period of adjustment in pregnancy (day 37-89) extended beyond expectations due to some evidence of mild ruminal acidosis after some initially high intakes that were followed by low intakes. During that time the diet was modified, in an attempt to improve palatability, by the addition of oaten chaff and the removal of an acidifying agent (NH4Cl) that was added initially to reduce the risk of urinary calculi. Eight ewes were removed due to inappetence, leaving 24 ewes to start the trial at day 90 of pregnancy. From day 90 of pregnancy until day 63 of lactation, liveweights of the ewes and their lambs were determined weekly and at parturition. Feed intakes of the ewes were determined weekly. Once lambing began, 1 ewe was removed as it gave birth to twin lambs (whereas the rest gave birth to a single lamb), 4 due to the loss of their lambs (2 to dystocia), and 1 due to copper toxicity. The PKM pellets were suspected to be the cause of the copper toxicity and so were removed in early lactation. Hence, the final statistical analysis using STATISTICA 8 (Repeated measures ANOVA for feed intake, One-way ANOVA for liveweight change and birth weight) was completed on 23 ewes for the pregnancy period (n = 11 fed H57; n = 12 control), and 18 ewes or lambs for the lactation period (n = 8 fed H57; n = 10 control). From day 90 of pregnancy until parturition the H57 supplemented ewes ate 17 more DM (g/day: 1041 vs 889, sed = 42.4, P = 0.04) and gained more liveweight (g/day: 193 vs 24.0, sed = 25.4, P = 0.0002), but produced lambs with a similar birthweight (kg: 4.18 vs 3.99, sed = 0.19, P = 0.54). Over the 63 days of lactation the H57 ewes ate similar amounts of DM but grew slower than the control ewes (g/day: 1.5 vs 97.0, sed = 21.7, P = 0.012). The lambs of the H57 ewes grew faster than those of the control ewes for the first 21 days of lactation (g/day: 356 vs 265, sed = 16.5, P = 0.006). These data support the findings of Norton et al (2008) and Kritas et al (2006) that certain Bacillus spp. supplements can improve the performance of pregnant and lactating ewes. In the current study we particularly highlighted the capacity of H57 to stimulate immature ewes to continue to grow maternal tissue through pregnancy, possibly through an enhanced appetite, which appeared then to stimulate a greater capacity to partition nutrients to their lambs through milk, at least for the first few weeks of lactation, a critical time for optimising lamb survival. To conclude, H57 can survive the steam pelleting process to improve feed intake and maternal liveweight gain in late pregnancy, and performance in early lactation, of first-parity ewes fed a diet based on PKM.

Influence of site, storage and steaming on Eucalyptus nitens log-end splitting

Key message Log-end splitting is one of the single most important defects in veneer logs. We show that log-end splitting in the temperate plantation species Eucalyptus nitens varies across sites and within-tree log position and increases with time in storage. Context Log-end splitting is one of the single most important defects in veneer logs because it can substantially reduce the recovery of veneer sheets. Eucalyptus nitens can develop log-end splits, but factors affecting log-end splitting in this species are not well understood. Aims The present study aims to describe the effect of log storage and steaming on the development of log-end splitting in logs from different plantations and log positions within the tree. Methods The study was conducted on upper and lower logs from each of 41 trees from three 20–22-year-old Tasmanian E. nitens plantations. Log-end splitting was assessed immediately after felling, after transport and storage in a log-yard, and just before peeling. A pre-peeling steam treatment was applied to half the logs. Results Site had a significant effect on splitting, and upper logs split more than lower logs with storage. Splitting increased with tree diameter breast height (DBH), but this relationship varied with site. The most rapidly growing site had more splitting even after accounting for DBH. No significant effect of steaming was detected. Conclusion Log-end splitting varied across sites and within-tree log position and increased with time in storage.