Strategic Analysis: A key factor in developing horticultural supply chains in transitional Asian economies

Globalisation is set to have a major impact on world horticultural production and distribution of fruit and vegetables throughout the world. In contrast to developing countries such as China, production and consumption of fresh fruit and vegetables in most developed countries is relatively static. For developed countries, we are starting to see consolidation in the number of farms producing fruit and vegetables with falling or static prices and real farm incomes. Global supply chains are now dominated by a few large multi-national retailers supplied by preferred trans-national distribution companies. The major competitive advantages that are emerging are consistency of supply of high quality product over an extended season and the control of genetic resources and their marketing. To capture these new competitive advantages, new strategic analyses and planning processes must be implemented. In the past, strategic analyses and planning has been undertaken on an ad hoc basis without accurate global intelligence. In the future, working ‘on the supply chain’ will become equally, if not more important, than working ‘in the supply chain’. A revised approach to strategic planning, which encompasses and adjusts for the changes caused by globalisation, is urgently needed. A new 6-step strategic analyses process is described.

Odour sampling. 2. Comparison of physical and aerodynamic characteristics of sampling devices: A review

Sampling devices differing greatly in shape, size and operating condition have been used to collect air samples to determine rates of emission of volatile substances, including odour. However, physical chemistry principles, in particular the partitioning of volatile substances between two phases as explained by Henrys Law and the relationship between wind velocity and emission rate, suggests that different devices cannot be expected to provide equivalent emission rate estimates. Thus several problems are associated with the use of static and dynamic emission chambers, but the more turbulent devices such as wind tunnels do not appear to be subject to these problems. In general, the ability to relate emission rate estimates obtained from wind tunnel measurements to those derived from device-independent techniques supports the use of wind tunnels to determine emission rates that can be used as input data for dispersion models.

Space allowances for confined livestock and their determination from allometric principles

The amount of space provided to animals governs important elements of their behaviour and, hence, is critical for their health and welfare. We review the use of allometric principles and equations to estimate the static space requirements of animals when standing and lying, and the space required for animals to feed, drink, stand-up and lie-down. We use the research literature relating to transportation and intensive housing of sheep and cattle to assess the validity of allometric equations for estimating space allowances. We investigated these areas because transportation and intensive housing provide points along a continuum in terms of the duration of confinement, (from hours to months) and spatial requirements are likely to increase with increasing duration of confinement, as animals will need to perform a greater behavioural repertoire for long-term survival, health and welfare. We find that, although there are theoretical reasons why allometric relationships to space allowances may vary slightly for different classes of stock, space allowances that have been demonstrated to have adverse effects on animal welfare during transportation correlated well with an inability to accommodate standing animals, as estimated from allometry. For intensive housing, we were able to detect a space allowance below which there were adverse effects on welfare. For short duration transportation during which animals remain standing, a space allowance per animal described by the allometric equation: area (m^2) = 0.020W^0.66, where W = liveweight (kg), would appear to be appropriate. Where it is desirable for all animals to lie simultaneously, then a minimum space allowance per animal described by the allometric equation: area (m^2) = 0.027W^0.66 appears to permit this, given that animals in a group time-share space. However, there are insufficient data to determine whether this allowance onboard a vehicle/vessel would enable animals to move and access food and water with ease. In intensive housing systems, a minimum space allowance per animal described by the allometric equation: area (m^2) = 0.033W^0.66 appears to be the threshold below which there are adverse effects on welfare. These suggested space allowances require verification with a range of species under different thermal conditions and, for transportation, under different conditions of vehicular/vessel stability. The minimum length of trough per animal (L in m) required for feeding and drinking can be determined from L = 0.064W^0.33, with the number of animals required to feed/drink simultaneously taken into account, together with any requirement to minimise competition. This also requires verification with a range of species. We conclude that allometric relationships are an appropriate basis for the formulation of space allowances for livestock.

Progress towards the eradication of mikania vine (Mikania micrantha) and limnocharis (Limnocharis flava) in northern Australia.

To eradicate a weed invasion, its extent must be delimited and each infestation must be extirpated. Measures for both of these criteria are utilized to assess the progress of current eradication programs targeting mikania vine and limnocharis in northern Australia. The known infested area for each species is less than 5 ha and has remained largely static for the last 3 or more years against a backdrop of refined and enhanced detection methods. This suggests that delimitation has been approached, if not achieved. Different methods of detection have their places, relative to the stage of the program and the spatial distribution of infestations. Although all known infestations of both species are effectively monitored and controlled, ongoing emergence from persistent seed banks limits progress towards the extirpation of infestations to a slow, but measurable, rate. Nomenclature: Glyphosate. N-phosphonomethyl)glycine; fluroxypyr, [(4-amino-3,5-dichloro-6-fluoro-2-pyridinyl)oxy]acetic acid; limnocharis, Limnocharis flava (L.) Buchenau LIFL5; mikania vine (mile-a-minute), Mikania micrantha Kunth MIKMI.

Advances in the culture of lobsters.

Commercial aquaculture of marine lobsters is an attractive proposition, as most species are high value with established market demand, and fishery production is static or diminishing. Nevertheless, achievement of commercial success will necessitate resolution of technical difficulties associated with on-growing of aggressive species (clawed lobsters) or with rearing the larvae, which for spiny and slipper lobsters is generally a painstaking and protracted process. Notwithstanding these technical challenges, increasing market demand for the product is driving a substantial research and development effort around the world to develop commercial lobster farming technology. This chapter reports on the status of that effort, the successes and obstacles.

Characterisation of wood properties and transverse anatomy for vacuum drying modelling of commercially important Australian hardwood species.

Characterisation and investigation of a number of key wood properties, critical for further modelling work, has been achieved. The key results were: • Morphological characterisation, in terms of fibre cell wall thickness and porosity, was completed. A clear difference in fibre porosity, size, wall thickness and orientation was evident between species. Results were consistent with published data for other species. • Viscoelastic properties of wood were shown to differ greatly between species and in the radial and tangential directions, largely due to anatomical and chemical variations. Consistent with published data, the radial direction shows higher stiffness, internal friction and glass transition temperature than the tangential directions. The loss of stiffness over the measured temperature range was greater in the tangential direction than the radial direction. Due to time dependant molecular relaxation, the storage modulus and glass transition temperature decreased with decreasing test frequency, approaching an asymptotic limit. Thus the viscoelastic properties measured at lower frequencies are more representative of static material. • Dynamic interactions between relative humidity, moisture content and shrinkage of four Australian hardwood timbers can be accurately monitored on micro-samples using a specialised experimental device developed by AgroParisTech – ENGREF. The device generated shrinkage data that varied between species but were consistent (repeatable) within a species. Collapse shrinkage was clearly evident with this method for Eucalyptus obliqua, but not with other species, consistent with industrial seasoning experience. To characterise the wood-water relations of this species, free of collapse, thinner sample sections (in the R-T plane) should be used.

MOE and MOR assessment technologies for improving graded recovery of exotic pines in Australia.

This project was designed to provide the structural softwood processing industry with the basis for improved green and dry grading to allow maximise MGP grade yields, consistent product performance and reduced processing costs. To achieve this, advanced statistical techniques were used in conjunction with state-of-the-art property measurement systems. Specifically, the project aimed to make two significant steps forward for the Australian structural softwood industry: • assessment of technologies, both existing and novel, that may lead to selection of a consistent, reliable and accurate device for the log yard and green mill. The purpose is to more accurately identify and reject material that will not make a minimum grade of MGP10 downstream; • improved correlation of grading MOE and MOR parameters in the dry mill using new analytical methods and a combination of devices. The three populations tested were stiffness-limited radiata pine, strength-limited radiata pine and Caribbean pine. Resonance tests were conducted on logs prior to sawmilling, and on boards. Raw data from existing in-line systems were captured for the green and dry boards. The dataset was analysed using classical and advanced statistical tools to provide correlations between data sets and to develop efficient strength and stiffness prediction equations. Stiffness and strength prediction algorithms were developed from raw and combined parameters. Parameters were analysed for comparison of prediction capabilities using in-line parameters, off-line parameters and a combination of in-line and off-line parameters. The results show that acoustic resonance techniques have potential for log assessment, to sort for low stiffness and/or low strength, depending on the resource. From the log measurements, a strong correlation was found between the average static MOE of the dried boards within a log and the predicted value. These results have application in segregating logs into structural and non-structural uses. Some commercial technologies are already available for this application such as Hitman LG640. For green boards it was found that in-line and laboratory acoustic devices can provide a good prediction of dry static MOE and moderate prediction for MOR.There is high potential for segregating boards at this stage of processing. Grading after the log breakdown can improve significantly the effectiveness of the mill. Subsequently, reductions in non-structural volumes can be achieved. Depending on the resource it can be expected that a 5 to 8 % reduction in non structural boards won’t be dried with an associated saving of $70 to 85/m3. For dry boards, vibration and a standard Metriguard CLT/HCLT provided a similar level of prediction on stiffness limited resource. However, Metriguard provides a better strength prediction in strength limited resources (due to this equipment’s ability to measure local characteristics). The combination of grading equipment specifically for stiffness related predictors (Metriguard or vibration) with defect detection systems (optical or X-ray scanner) provides a higher level of prediction, especially for MOR. Several commercial technologies are already available for acoustic grading on board such those from Microtec, Luxscan, Falcon engineering or Dynalyse AB for example. Differing combinations of equipment, and their strategic location within the processing chain, can dramatically improve the efficiency of the mill, the level of which will vary depending of the resource. For example, an initial acoustic sorting on green boards combined with an optical scanner associated with an acoustic system for grading dry board can result in a large reduction of the proportion of low value low non-structural produced. The application of classical MLR on several predictors proved to be effective, in particular for MOR predictions. However, the usage of a modern statistics approach(chemometrics tools) such as PLS proved to be more efficient for improving the level of prediction. Compared to existing technologies, the results of the project indicate a good improvement potential for grading in the green mill, ahead of kiln drying and subsequent cost-adding processes. The next stage is the development and refinement of systems for this purpose.

Testing the effectiveness of the SKIM foam fractionator to reduce nutrient levels in prawn farm effluent

To experimentally investigate the effect of the “SKIM” mechanical foam fractionator on suspended material and the nutrient levels in prawn farm effluent, a series of standardised short-term treatments were applied to various effluent types in a static 10,000-litre water body. Prawn pond effluents were characterised by watercolour and dominance of phytoplankton species. Three effluent types were tested, namely 1) particulate-rich effluent with little apparent phytoplankton, 2) green mircoalgal bloom predominately made up of single celled phytoplankton, and 3) brown microalgal bloom with higher prevalence of diatoms. The effluent types were similar (P>0.05) in non-volatile particulate material, and nitrate/nitrite but varied from each other in the following ways: 1) The particulate-rich effluents were lower (P<0.05) in volatile solids (compared to brown blooms), total Kjeldahl nitrogen, dissolved organic nitrogen, dissolved organic phosphorus and chlorophyll a (compared to both green and brown blooms). 2) The brown blooms were higher (P<0.05) in ammonia (compared to green blooms), total nitrogen and total phosphorus (compared to both green and particulate-rich effluent), but were lower (P<0.05) in inorganic phosphorus (compared to both green and particulate-rich effluent). 3) The green blooms were higher (P<0.05) in dissolved (both organic and inorganic) phosphorus (compared to both brown and particulate-rich effluents). Although the effluent types varied significantly in these aspects the effect of the Skim treatment was similar for all parameters measured except total phosphorus. Bloom type and Skim-treatment period significantly (P<0.05) affected total Kjeldahl phosphorus concentrations. For all effluent types there was a continuous significant reduction (P<0.05) in total Kjeldahl phosphorus during the initial 6-hour treatment period. Levels of total suspended solids and volatile suspended solids in all effluent types were significantly (P<0.05) reduced in the first 2 hours but not thereafter. Non-volatile suspended solids were also significantly (P<0.05) reduced in the first 2 hours (30 to 40 % reduction) and a further 40% reduction occurred in the particulate-rich effluent over the next 2 hours. Mean values for total ammonia, dissolved organic nitrogen, total Kjeldahl nitrogen, total nitrogen, chlorophyll a and dissolved organic or inorganic phosphorus levels were not significantly (P>0.05) affected by the Skim unit in any bloom type during the initial 6 hours of testing. Nevertheless, non-significant nitrogen reductions did occur. Foam production by the Skim unit varied with different blooms, resulting in different concentrate volumes and different end points for separate experiments. Concentrate volumes were generally high for the particulate-rich and green blooms (175 – 370 litres) and low for the brown blooms (25 – 80 litres). This was due to the low tendency of the brown bloom to produce foam. This generated higher nutrient concentrations in the associated condensed foam, but may have limited the treatment efficiency. The results suggest that in this application, the Skim unit did not remove micro-algae as effectively as was anticipated. However, it was effective at removing other suspended solids. Considering these attributes and the other uses of this machinery documented by the manufactures, the unit’s oxygenation mixing capacities coupled with inorganic solids removal may provide a suitable mechanism for construction of a continuously mixed bioreactor that utilises the filtration and profit making abilities of bivalves.

Hanging drop: An in vitro air toxic exposure model using human lung cells in 2D and 3D structures

Using benzene as a candidate air toxicant and A549 cells as an in vitro cell model, we have developed and validated a hanging drop (HD) air exposure system that mimics an air liquid interface exposure to the lung for periods of 1 h to over 20 days. Dose response curves were highly reproducible for 2D cultures but more variable for 3D cultures. By comparing the HD exposure method with other classically used air exposure systems, we found that the HD exposure method is more sensitive, more reliable and cheaper to run than medium diffusion methods and the CULTEX (R) system. The concentration causing 50% of reduction of cell viability (EC50) for benzene, toluene, p-xylene, m-xylene and o-xylene to A549 cells for 1 h exposure in the HD system were similar to previous in vitro static air exposure. Not only cell viability could be assessed but also sub lethal biological endpoints such as DNA damage and interleukin expressions. An advantage of the HD exposure system is that bioavailability and cell concentrations can be derived from published physicochemical properties using a four compartment mass balance model. The modelled cellular effect concentrations EC50(cell) for 1 h exposure were very similar for benzene, toluene and three xylenes and ranged from 5 to 15 mmol/kg(dry weight) which corresponds to the intracellular concentration of narcotic chemicals in many aquatic species, confirming the high sensitivity of this exposure method. (C) 2013 Elsevier B.V. All rights reserved.

Description of vectors of arboviruses of livestock in Northern Australia

The project aimed to detect exotic C"11coides species recently established in northern Australia and to map the distribution of Cullcoid"' bi'e\, nth'sis and C. 1.1-, oddiill Western Australia and NT. Between February 1990 and June 1992, collections were Inade throughout Cape York Peninsula, Nortlierii Territory and northern and central Western Australia. Six previously unreported species were collected. These species an'e considered unlikely to be recent jininigrants and seein to pose little threat as potential arboviiT. Is vectors. C. woddi was restricted to coastal 1101tlierii Qld, the northernmost areas of NT and the northern Kiinberley region in WA. 111 NT C. bi'evitai'sis was collected as far soutli as Katlierine. In WA it was collected throughout the Kiinberley and in the Pilbara region ill all area bounded by Nullagine, KanTatha and 300km nortli of Carnalvon. C. bi'evilcii'sis reinains tlie only Guncoide. s species of known 11npoitance as a vector of livestock an'boviruses to extend into Inajor sheep-grazing areas. Generally, CUIicoides distributions in northern Australia between 1990 and 1992 were coinparable but not identical to those defined ill surveys conducted ill tlie 1970's and 1980's. Species distributions were not static and will continue to fluctuate witli variation ill rainfall. . .