29 resultados para Production methods

em eResearch Archive - Queensland Department of Agriculture


Relevância:

60.00% 60.00%

Publicador:

Resumo:

Summary Prototype sand-worm filtration beds were constructed at two prawn farms and one fish farm to assess and demonstrate their polychaete (marine worm) production and wastewater remediation capacities at semi-commercial scale. Wastewater treatment properties were monitored and worms produced were assessed and either sold for bait or used by the farms’ hatcheries as broodstock (prawn or fish breeder) feed. More than 34 megalitres of prawn- and fish-pond water was beneficially treated in the 116-319-d trial. The design of the polychaete-assisted sand filters (PASFs) constructed at each farm affected their water handling rates, which on average ranged from 315 to 1000 L m-2 d-1 at the three farms. A low profile design incorporating shallow bunded ponds made from polyethylene liner and timber stakes provided the easiest method of construction. This simple design applied at broad scale facilitated the highest quantities of treated water and the greatest worm production. Designs with higher sides increased the head pressure above the sand bed surface, thus increasing the amount of water that could be treated each day. Most water qualities were affected in a similar way to that demonstrated in the previous tank trials: dissolved oxygen, pH, total suspended solids and chlorophyll a levels were all consistently significantly lowered as pond water percolated through the sand bed, and dissolved forms of nitrogen and phosphorus were marginally increased on several occasions. However, unlike the previous smaller-scale tank trials, total nitrogen (TN) and total phosphorus (TP) levels were both significantly lowered by these larger-scale PASFs. The reasons for this are still unclear and require further research. Maximum TN and TP removals detected in the trial were 48.8% and 67.5%, respectively, and average removals (in unfed beds) at the three farms ranged from 20.0 to 27.7% for TN and from 22.8 to 40.8% for TP. Collectively, these results demonstrate the best suspended solids, chlorophyll and macronutrient removal capacities so far reported for any mariculture wastewater treatment methodology to date. Supplemental feeding of PASFs with fish meal was also investigated at one farm as a potential means of increasing their polychaete biomass production. Whilst fed beds produced higher biomass (152 ± 35 g m-2) compared with unfed beds (89 ± 17 g m-2) after 3.7 months of operation, the low number of replicates (2) prevented statistically significant differences from being demonstrated for either growth or survival. At harvest several months later, worm biomass production was estimated to be similar to, or in slight excess of, previously reported production levels (300-400 g m-2). Several qualities of filtered water appear to have been affected by supplemental feeding: it appeared to marginally lower dissolved oxygen and pH levels, and increased the TN and TP levels though not so much to eliminate significant beneficial water treatment effects. Periodic sampling during an artificial-tide demonstrated the tendency for treated-water quality changes during the first hour of filtration. Total nitrogen and ammonia peaked early in the tidal flow and then fell to more stable levels for the remainder of the filtration period. Other dissolved nutrients also showed signs of this sand-bed-flushing pattern, and dissolved oxygen tended to climb during the first hour and become more stable thereafter. These patterns suggest that the routine sampling of treated water undertaken at mid-inflow during the majority of the wider study would likely have overestimated the levels of TN and dissolved nutrients discharged from the beds, and hence underestimated the PASFs treatment efficacies in this regard. Analyses of polychaete biomass collected from each bed in the study revealed that the worms were free from contamination with the main prawn viruses that would create concerns for their feeding to commercial prawn broodstock in Australia. Their documented proximal and nutritional contents also provide a guide for hatchery operators when using live or frozen stock. Their dry matter content ranged from 18.3 to 22.3%, ash ranged from 10.2 to 14.0%, gross energy from 20.2 to 21.5 MJ kg-1, and fat from 5.0 to 9.2%. Their cholesterol levels ranged from 0.86 to 1.03% of dry matter, whilst total phospholipids range from 0.41 to 0.72%. Thirty-one different fatty acids were present at detectable (≥0.005% of dry matter) levels in the sampled worm biomass. Palmitic acid was by far the most prevalent fatty acid detected (1.21 ± 0.18%), followed by eicosapentaenoic (EPA) (0.48 ± 0.03%), stearic (0.46 ± 0.04%), vaccenic (0.38 ± 0.05%), adrenic (0.35 ± 0.02%), docosadienoic (0.28 ± 0.02%), arachidonic (AA) (0.22 ± 0.01%), palmitoleic (0.20 ± 0.04%) and 23 other fatty acids with average contents of less than 0.2% of dry matter. Supplemental feeding with fish meal at one farm appeared to increase the docosahexaenoic acid (DHA) content of the worms considerably, and modify the average AA : EPA : DHA from 1.0 : 2.7 : 0.3 to 1.0 : 2.0 : 1.1. Consistent with previous results, the three most heavily represented amino acids in the dry matter of sampled worms were glutamic acid (8.5 ± 0.2%), aspartic acid (5.5 ± 0.1%) and glycine (4.9 ± 0.5%). These biomass content results suggest that worms produced in PASF systems are well suited to feeding to prawn and fish broodstock, and provide further strong evidence of the potential to modify their contents for specific nutritional uses. The falling wild-fishery production of marine bloodworms in Queensland is typical of diminishing polychaete resources world-wide and demonstrates the need to develop sustainable production methods here and overseas. PASF systems offer the dual benefits of wastewater treatment for environmental management and increased productivity through a valuable secondary crop grown exclusively on waste nutrients.

Relevância:

40.00% 40.00%

Publicador:

Resumo:

Historical stocking methods of continuous, season-long grazing of pastures with little account of growing conditions have caused some degradation within grazed landscapes in northern Australia. Alternative stocking methods have been implemented to address this degradation and raise the productivity and profitability of the principal livestock, cattle. Because information comparing stocking methods is limited, an evaluation was undertaken to quantify the effects of stocking methods on pastures, soils and grazing capacity. The approach was to monitor existing stocking methods on nine commercial beef properties in north and south Queensland. Environments included native and exotic pastures and eucalypt (lighter soil) and brigalow (heavier soil) land types. Breeding and growing cattle were grazed under each method. The owners/managers, formally trained in pasture and grazing management, made all management decisions affecting the study sites. Three stocking methods were compared: continuous (with rest), extensive rotation and intensive rotation (commonly referred to as 'cell grazing'). There were two or three stocking methods examined on each property: in total 21 methods (seven continuous, six extensive rotations and eight intensive rotations) were monitored over 74 paddocks, between 2006 and 2009. Pasture and soil surface measurements were made in the autumns of 2006, 2007 and 2009, while the paddock grazing was analysed from property records for the period from 2006 to 2009. The first 2 years had drought conditions (rainfall average 3.4 decile) but were followed by 2 years of above-average rainfall. There were no consistent differences between stocking methods across all sites over the 4 years for herbage mass, plant species composition, total and litter cover, or landscape function analysis (LFA) indices. There were large responses to rainfall in the last 2 years with mean herbage mass in the autumn increasing from 1970 kg DM ha(-1) in 2006-07 to 3830 kg DM ha(-1) in 2009. Over the same period, ground and litter cover and LFA indices increased. Across all sites and 4 years, mean grazing capacity was similar for the three stocking methods. There were, however, significant differences in grazing capacity between stocking methods at four sites but these differences were not consistent between stocking methods or sites. Both the continuous and intensive rotation methods supported the highest average annual grazing capacity at different sites. The results suggest that cattle producers can obtain similar ecological responses and carry similar numbers of livestock under any of the three stocking methods.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Northern Australian dairy farms have a large area of tropical dryland grass pasture available for use as summer pastures. Late summer-autumn in sub-tropical Australia is traditionally a difficult period in which to produce milk because of the decline in both quality and quantity of tropical grasses (Ehrlich et al. 1994). Options to improve autumn feed on dairy farms include introducing forage crops and conservation, increasing concentrate feeding and introducing legumes. Perennial tropical legumes have not been successful at this time of year because of their inability to sustain stocking rates above one cow/ha. This experiment, conducted on farms, was designed to test if annual crop legumes could be successfully oversown into tropical grass areas using minimal till methods to measure the subsequent impact on milk production on farms. Previous experiments using annual legumes in plots at Mutdapilly Research Station had demonstrated yields up to 10 t/ha can be achieved using annual tropical legumes with protein levels as high as 20% in the whole legume plant. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

In many designed experiments with animals liveweight is recorded several times during the trial. Such data are commonly referred to as repeated measures data. An aim of such experiments is generally to compare the growth patterns for the applied treatments. This paper discusses some of the methods of analysing repeated measures data and illustrates the use of cubic smoothing splines to describe irregular cattle growth data. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The widespread and increasing resistance of internal parasites to anthelmintic control is a serious problem for the Australian sheep and wool industry. As part of control programmes, laboratories use the Faecal Egg Count Reduction Test (FECRT) to determine resistance to anthelmintics. It is important to have confidence in the measure of resistance, not only for the producer planning a drenching programme but also for companies investigating the efficacy of their products. The determination of resistance and corresponding confidence limits as given in anthelmintic efficacy guidelines of the Standing Committee on Agriculture (SCA) is based on a number of assumptions. This study evaluated the appropriateness of these assumptions for typical data and compared the effectiveness of the standard FECRT procedure with the effectiveness of alternative procedures. Several sets of historical experimental data from sheep and goats were analysed to determine that a negative binomial distribution was a more appropriate distribution to describe pre-treatment helminth egg counts in faeces than a normal distribution. Simulated egg counts for control animals were generated stochastically from negative binomial distributions and those for treated animals from negative binomial and binomial distributions. Three methods for determining resistance when percent reduction is based on arithmetic means were applied. The first was that advocated in the SCA guidelines, the second similar to the first but basing the variance estimates on negative binomial distributions, and the third using Wadley’s method with the distribution of the response variate assumed negative binomial and a logit link transformation. These were also compared with a fourth method recommended by the International Co-operation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal Products (VICH) programme, in which percent reduction is based on the geometric means. A wide selection of parameters was investigated and for each set 1000 simulations run. Percent reduction and confidence limits were then calculated for the methods, together with the number of times in each set of 1000 simulations the theoretical percent reduction fell within the estimated confidence limits and the number of times resistance would have been said to occur. These simulations provide the basis for setting conditions under which the methods could be recommended. The authors show that given the distribution of helminth egg counts found in Queensland flocks, the method based on arithmetic not geometric means should be used and suggest that resistance be redefined as occurring when the upper level of percent reduction is less than 95%. At least ten animals per group are required in most circumstances, though even 20 may be insufficient where effectiveness of the product is close to the cut off point for defining resistance.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Materials and Methods. Testes were collected a t castration or a t slaughter from purebred Brahman (B); Brahman cross (BX - half and three quarter); Sahiwal cross (SX – three quarter and seven eighths); and purebred and three quarter Santa Gertrudis (SG) bulls of known ages between 19 and 27 months and drawn from herds in northern coastal Queensland. 13th Biennial Conference. August 1980, Perth Western Australia.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

1. The European red fox Vulpes vulpes represents a continuing threat to both livestock and native vertebrates in Australia, and is commonly managed by setting ground-level baits impregnated with 1080 (sodium fluoroacetate) poison. However, the long-term effectiveness of such control campaigns is likely to be limited due to the ability of foxes to disperse over considerable distances and to swiftly recolonize areas from where they had been removed. 2. To investigate the effectiveness of fox baiting in a production landscape, we assessed the potential for foxes to reinvade baited farm property areas within the jurisdiction of the Molong Rural Lands Protection Board (RLPB), an area of 815 000 ha on the central tablelands of New South Wales, Australia. The spatial distribution and timing of fox baiting campaigns between 1998 and 2002 was estimated from RLPB records and mapped using Geographical Information System software. The effectiveness of the control campaign was assessed on the basis of the likely immigration of foxes from non-baited farms using immigration distances calculated from published relationships between dispersal distance and home range size. 3. Few landholders undertook baiting campaigns in any given year, and the area baited was always so small that no baited property would have been sufficiently far from an unbaited property to have been immune from immigrating individuals. It is likely, therefore, that immigration onto farms negated any long-term effects of baiting operations. This study highlights some of the key deficiencies in current baiting practices in south-eastern Australia and suggests that pest management programmes should be monitored using such methods to ensure they achieve their goals.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

'Goldfinger', a tetraploid banana produced from the Fundación Hondureña de Investigación Agrícola (FHIA) breeding program, was released to the Australian industry in 1995. It was promoted as an apple-flavoured dessert banana with resistance to Fusarium wilt race 1 and subtropical race 4, as well as resistance to black and yellow Sigatoka (Mycosphaerella fijiensis and M. musicola, respectively). This study was initiated to provide agronomic information to the banana industry, which was under threat from Fusarium wilt, on a new cultivar which could replace 'Williams' (AAA, Cavendish subgroup) or 'Lady Finger' (AAB, Pome subgroup) in those areas affected by Fusarium wilt. Also few studies had reported on the production characteristics of the new tetraploid hybrids, especially from subtropical areas, and therefore two field sites, one a steep-land farm and the other a level, more productive site, were selected for planting density and spatial arrangement treatments. The optimum density in terms of commercial production, taking into account bunch weight, finger size, length of the production cycle, plant height and ease of management, was 1680 plants/ha on the steep-land site where plants were planted in single rows with 2.5 m × 2.5 m spacings. However on the level site a double-row triangular layout with inter-row distances of 4.5 m to allow vehicular access (1724 plants/ha) gave the best results. With this arrangement plants were in an alternate, triangular arrangement along a row and a spacing of 1.5 m between plants at the points of each triangle and between each block of triangles.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

In semi-arid areas such as western Nebraska, interest in subsurface drip irrigation (SDI) for corn is increasing due to restricted irrigation allocations. However, crop response quantification to nitrogen (N) applications with SDI and the environmental benefits of multiple in-season (IS) SDI N applications instead of a single early-season (ES) surface application are lacking. The study was conducted in 2004, 2005, and 2006 at the University of Nebraska-Lincoln West Central Research and Extension Center in North Platte, Nebraska, comparing two N application methods (IS and ES) and three N rates (128, 186, and 278 kg N ha(-1)) using a randomized complete block design with four replications. No grain yield or biomass response was observed in 2004. In 2005 and 2006, corn grain yield and biomass production increased with increasing N rates, and the IS treatment increased grain yield, total N uptake, and gross return after N application costs (GRN) compared to the ES treatment. Chlorophyll meter readings taken at the R3 corn growth stage in 2006 showed that less N was supplied to the plant with ES compared to the IS treatment. At the end of the study, soil NO3-N masses in the 0.9 to 1.8 m depth were greater under the IS treatment compared to the ES treatment. Results suggested that greater losses of NO3-N below the root zone under the ES treatment may have had a negative effect on corn production. Under SDI systems, fertigating a recommended N rate at various corn growth stages can increase yields, GRN, and reduce NO3-N leaching in soils compared to concentrated early-season applications.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Plant tissue culture has been used for a number of years to produce micropropagated strawberry plants for planting into runner growing beds in the Stanthorpe (Queensland) and Bothwell (Tasmania) regions. This process has allowed the rapid release of new cultivars from the LAWS (Late Autumn, Winter, Spring) breeding program into the current runner production system. Micro-propagation in vitro allows plants to be produced during the autumn and winter months, when mother plants would normally be in a fruit production phase in the field in Queensland. The plants produced are of a high health status when they are planted. The subsequent arrival and build up of various diseases in the runner fields are closely monitored. Using tissue culture for the first generation reduces the time the plants spend in the field by twelve months, reducing disease incidence. To date, any disease outbreak has been successfully managed using early detection and rapid response methods.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Maize is a highly important crop to many countries around the world, through the sale of the maize crop to domestic processors and subsequent production of maize products and also provides a staple food to subsistance farms in undeveloped countries. In many countries, there have been long-term research efforts to develop a suitable hardness method that could assist the maize industry in improving efficiency in processing as well as possibly providing a quality specification for maize growers, which could attract a premium. This paper focuses specifically on hardness and reviews a number of methodologies as well as important biochemical aspects of maize that contribute to maize hardness used internationally. Numerous foods are produced from maize, and hardness has been described as having an impact on food quality. However, the basis of hardness and measurement of hardness are very general and would apply to any use of maize from any country. From the published literature, it would appear that one of the simpler methods used to measure hardness is a grinding step followed by a sieving step, using multiple sieve sizes. This would allow the range in hardness within a sample as well as average particle size and/or coarse/fine ratio to be calculated. Any of these parameters could easily be used as reference values for the development of near-infrared (NIR) spectroscopy calibrations. The development of precise NIR calibrations will provide an excellent tool for breeders, handlers, and processors to deliver specific cultivars in the case of growers and bulk loads in the case of handlers, thereby ensuring the most efficient use of maize by domestic and international processors. This paper also considers previous research describing the biochemical aspects of maize that have been related to maize hardness. Both starch and protein affect hardness, with most research focusing on the storage proteins (zeins). Both the content and composition of the zein fractions affect hardness. Genotypes and growing environment influence the final protein and starch content and. to a lesser extent, composition. However, hardness is a highly heritable trait and, hence, when a desirable level of hardness is finally agreed upon, the breeders will quickly be able to produce material with the hardness levels required by the industry.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Aims: To examine the prevalence of bacteriocin production in Streptococcus bovis isolates from Australian ruminants and the feasibility of industrial production of bacteriocin. Methods and Results: Streptococcus bovis strains were tested for production of bacteriocin-like inhibitory substances (BLIS) by antagonism assay against Lactococcus lactis. BLIS production was associated with source animal location (i.e. proximity of other bacteriocin-positive source animals) rather than ruminant species/breed or diet. One bacteriocin showing strong inhibitory activity (Sb15) was isolated and examined. Protein sequence, stability and activity spectrum of this bovicin were very similar to bovicin HC5. Production could be increased through serial culturing, and increased productivity could be partially maintained during cold storage of cultures. Conclusions: BLIS production is geographically widely distributed in Eastern Australia, and it appears that the bacteriocin+ trait is maintained in animals at the same location. The HC5-like bacteriocin, originally identified in North America, is also found in Australia. Production of bacteriocin can be increased through serial culturing. Significance and Impact of the Study: The HC5-like bacteriocins appear to have a broad global distribution. Serial culturing may provide a route towards commercial manufacturing for use in industrial applications, and purified bacteriocin from S. bovis Sb15 could potentially be used to prevent food spoilage or as a feed additive to promote growth in ruminant species.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Inter-specific Corymbia hybrids are of increasing interest to plantation forestry, yet there is little knowledge of the most suitable controlled pollination methods for this genus. Inter-specific crosses were made between C. torelliana [CT(maternal parent)] and C. citriodora subsp. variegata (CCV), C. henryi (CH) and C. citriodora subsp. citriodora (CCC) using conventional pollination, one-stop pollination (OSP) and artificially-induced protogyny on yellow buds (AIP Y) pollination methods. Additional treatments included AIP on green buds (AIP G) and the use of exclusion bags for the OSP and AIP methods. Inter-specific hybrids (CT x CCV, CT x CH and CT x CCC) were successfully created using all three pollination methods. The AIP Y treatment provided the highest seed yields and achieved time savings of >41% over the conventional and OSP methods, resulting in up to five-fold increases in operator productivity. However, the AIP Y treatment also had the highest C. torelliana contamination levels (9.3–13.2%). The use of exclusion bags with the AIP method had minimal effect on contamination rates, indicating a high proportion of selfpollen contamination. Contamination rates varied between maternal parents, suggesting variation in selfcompatibility for C. torelliana individuals. AIP using semi-ripe green buds was not effective at reducing selfing and had low operator productivity. The AIP method is suitable for use in a large-scale hybrid breeding program for C. torelliana. When self-pollination effects are managed, it could greatly reduce the costs associated with the production of seed of elite family crosses for commercial forestry deployment.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Development of regeneration and transformation methods for genetic improvement of rootstocks for mango, avocado and citrus.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Early season beneficials in brassica crops.