Odour Emissions from Tunnel Ventilated Poultry Housing

In Australia, factors such as local planning processes, urban encroachment into rural areas and intensification of the poultry industry have increased the potential for odour and dust nuisance. At present, accurate estimates of odour emissions from mechanically ventilated poultry housing systems do not exist for Australian conditions. This has made the poultry industry vulnerable to unsubstantiated criticism. Recently, the Australian poultry industry have made a significant investment in research to obtain accurate estimates of odour, dust and volatile chemical emission rates from typical poultry housing systems. This paper describes the measurement of odour emissions from tunnel ventilated poultry housing systems in different climatic zones in Queensland and Victoria, Australia (humid sub-tropical and Mediterranean respectively) during two seasons (summer and winter). Samples were collected at defined intervals over typical batch production cycles to define the odour emission profiles. These samples were analysed using dynamic olfactometry according to the Australian Standard 4323.3 to derive the odour concentration values. Ventilation rates were measured concurrently, allowing the calculation of odour emission rates. Odour concentration and emission rates were assessed in terms of ventilation rate, ambient and shed air temperature and relative humidity and litter moisture status. Odour emission rates varied with bird age. Seasonal differences in odour emission rate were also observed.

A simple, one-tube assay for the simultaneous detection and diagnosis of ten Australian poultry Eimeria

Coccidiosis is a costly worldwide enteric disease of chickens caused by parasites of the genus Eimeria. At present, there are seven described species that occur globally and a further three undescribed, operational taxonomic units (OTUs X, Y, and Z) that are known to infect chickens from Australia. Species of Eimeria have both overlapping morphology and pathology and frequently occur as mixed-species infections. This makes definitive diagnosis with currently available tests difficult and, to date, there is no test for the detection of the three OTUs. This paper describes the development of a PCR-based assay that is capable of detecting all ten species of Eimeria, including OTUs X, Y, and Z in field samples. The assay is based on a single set of generic primers that amplifies a single diagnostic fragment from the mitochondrial genome of each species. This one-tube assay is simple, low-cost, and has the capacity to be high throughput. It will therefore be of great benefit to the poultry industry for Eimeria detection and control, and the confirmation of identity and purity of vaccine strains.

Avian influenza in Australia: a summary of 5 years of wild bird surveillance

BackgroundAvian influenza viruses (AIVs) are found worldwide in numerous bird species, causing significant disease in gallinaceous poultry and occasionally other species. Surveillance of wild bird reservoirs provides an opportunity to add to the understanding of the epidemiology of AIVs. MethodsThis study examined key findings from the National Avian Influenza Wild Bird Surveillance Program over a 5-year period (July 2007-June 2012), the main source of information on AIVs circulating in Australia. ResultsThe overall proportion of birds that tested positive for influenza A via PCR was 1.90.1%, with evidence of widespread exposure of Australian wild birds to most low pathogenic avian influenza (LPAI) subtypes (H1-13, H16). LPAI H5 subtypes were found to be dominant and widespread during this 5-year period. ConclusionGiven Australia's isolation, both geographically and ecologically, it is important for Australia not to assume that the epidemiology of AIV from other geographic regions applies here. Despite all previous highly pathogenic avian influenza outbreaks in Australian poultry being attributed to H7 subtypes, widespread detection of H5 subtypes in wild birds may represent an ongoing risk to the Australian poultry industry.

Bentonite can decrease ammonia volatilisation losses from poultry litter: laboratory studies

Ammonia volatilisation from manure materials within poultry sheds can adversely affect production, and also represents a loss of fertiliser value from the spent litter. This study sought to compare the ability of alum and bentonite to decrease volatilisation losses of ammonia from spent poultry litter. An in-vessel volatilisation trial with air flushing, ammonia collection, and ammonia analysis was conducted over 64 days to evaluate the mitigation potential of these two materials. Water-saturated spent litter was incubated at 25°C in untreated condition (control) or with three treatments: an industry-accepted rate of alum [4% Al2(SO4)3·18H2O by dry mass of litter dry mass; ALUM], air-dry bentonite (127% by dry mass; BENT), or water-saturated bentonite (once again at 127% by dry mass; SATBENT). A high proportion of the nitrogen contained in the untreated spent litter was volatilised (62%). Bentonite additions were superior to alum additions at retaining spent litter ammonia (nitrogen losses: 15%, SATBENT; 34%, BENT; 54%, ALUM). Where production considerations favour comparable high rates of bentonite addition (e.g. where the litter is to be re-formulated as a fertiliser), this clay has potential to decrease ammonia volatilisation either in-shed or in spent litter stockpiles or formulated products, without the associated detrimental effect of alum on phosphorus availability.

Establishment of an Australian mild onion industry - the sensory component

In recent years, there has been increasing interest from growers, merchants, supermarkets and consumers in the establishment of a national mild onion industry. Imperative to the success of the emergent industry is the application of the National Mild Onion Certification Scheme that will establish standards and recommendations to be met by growers to allow them to declare their product as certified mild onions. The use of sensory evaluation techniques has played an imperative role throughout the project timeline that has also included varietal evaluation, evaluation of current agronomic practices and correlation of chemical analysis data. Raw onion consumer acceptance testing on five different onion varieties established preferences amongst the varieties for odour, appearance, flavour, texture and overall and differences in the level of pungency and aftertaste perceived. Demographic information was obtained regarding raw and cooked onion use, frequency of consumption and responses to the idea of a mild, less pungent onion. Additionally, focus groups were conducted to further investigate consumer attitudes to onions. Currently, a trained onion panel is being established to evaluate several odour, flavour and aftertaste attributes. Sample assessments will be conducted in January 2004 and correlated with chemical analyses that will hopefully provide the corner-stone for the anticipated Certification Scheme.

Effective Use in Livestock Feeds of Mouldy and Weather-damaged Grain Containing Mycotoxins-Case Histories and Economic Assessments Pertaining to Pig and Poultry Industries of Queensland

Mould growth in field crops or stored grain reduces starch and lipid content, with consequent increases in fibre, and an overall reduction in digestible energy; palatability is often adversely affected. If these factors are allowed for, and mycotoxin concentrations are low, there are sound economic reasons for using this cheaper grain. Mycotoxins are common in stock feed but their effects on animal productivity are usually slight because either the concentration is too low or the animal is tolerant to the toxin. In Australia, aflatoxins occur in peanut by-products and in maize and sorghum if the grain is moist when stored. Zearalenone is found in maize and in sorghum and wheat in wetter regions. Nivalenol and deoxynivalenol are found in maize and wheat but at concentrations that rarely affect pigs, with chickens and cattle being even more tolerant. Other mycotoxins including cyclopiazonic acid, T-2 toxin, cytochalasins and tenuazonic acid are produced by Australian fungi in culture but are not found to be significant grain contaminants. Extremely mouldy sorghum containing Alternaria and Fusarium mycotoxins decreased feed conversion in pigs and chickens by up to 14%. However, E moniliforme- and Diplodia maydis-infected maize produced only slight reductions in feed intake by pigs and Ustilago- infected barley produced no ill effects. Use of these grains would substantially increase profits if the grain can be purchased cheaply.

The reliability of supply of feed grains in the northern region

Reliability of supply of feed grain has become a high priority issue for industry in the northern region. Expansion by major intensive livestock and industrial users of grain, combined with high inter-annual variability in seasonal conditions, has generated concern in the industry about reliability of supply. This paper reports on a modelling study undertaken to analyse the reliability of supply of feed grain in the northern region. Feed grain demand was calculated for major industries (cattle feedlots, pigs, poultry, dairy) based on their current size and rate of grain usage. Current demand was estimated to be 2.8Mt. With the development of new industrial users (ethanol) and by projecting the current growth rate of the various intensive livestock industries, it was estimated that demand would grow to 3.6Mt in three years time. Feed grain supply was estimated using shire scale yield prediction models for wheat and sorghum that had been calibrated against recent ABS production data. Other crops that contribute to a lesser extent to the total feed grain pool (barley, maize) were included by considering their production relative to the major winter and summer grains, with estimates based on available production records. This modelling approach allowed simulation of a 101-year time series of yield that showed the extent of the impact of inter-annual climate variability on yield levels. Production estimates were developed from this yield time series by including planted crop area. Area planted data were obtained from ABS and ABARE records. Total production amounts were adjusted to allow for any export and end uses that were not feed grain (flour, malt etc). The median feed grain supply for an average area planted was about 3.1Mt, but this varied greatly from year to year depending on seasonal conditions and area planted. These estimates indicated that supply would not meet current demand in about 30% of years if a median area crop were planted. Two thirds of the years with a supply shortfall were El Nino years. This proportion of years was halved (i.e. 15%) if the area planted increased to that associated with the best 10% of years. Should demand grow as projected in this study, there would be few years where it could be met if a median crop area was planted. With area planted similar to the best 10% of years, there would still be a shortfall in nearly 50% of all years (and 80% of El Nino years). The implications of these results on supply/demand and risk management and investment in research and development are briefly discussed.

Climate information needs of Gascoyne-Murchison pastoralists: a representative study of the Western Australian grazing industry

The Gascoyne-Murchison region of Western Australia experiences an arid to semi-arid climate with a highly variable temporal and spatial rainfall distribution. The region has around 39.2 million hectares available for pastoral lease and supports predominantly catle and sheep grazing leases. In recent years a number of climate forecasting systems have been available offering rainfall probabilities with different lead times and a forecast period; however, the extent to which these systems are capable of fulfilling the requirements of the local pastoralists is still ambiguous. Issues can range from ensuring forecasts are issued with sufficient lead time to enable key planning or decisions to be revoked or altered, to ensuring forecast language is simple and clear, to negate possible misunderstandings in interpretation. A climate research project sought to provide an objective method to determine which available forecasting systems had the greatest forecasting skill at times of the year relevant to local property management. To aid this climate research project, the study reported here was undertaken with an overall objective of exploring local pastoralists' climate information needs. We also explored how well they understand common climate forecast terms such as 'mean', median' and 'probability', and how they interpret and apply forecast information to decisions. A stratified, proportional random sampling was used for the purpose of deriving the representative sample based on rainfall-enterprise combinations. In order to provide more time for decision-making than existing operational forecasts that are issued with zero lead time, pastoralists requested that forecasts be issued for May-July and January-March with lead times counting down from 4 to 0 months. We found forecasts of between 20 and 50 mm break-of-season or follow-up rainfall were likely to influence decisions. Eighty percent of pastoralists demonstrated in a test question that they had a poor technical understanding of how to interpret the standard wording of a probabilistic median rainfall forecast. this is worthy of further research to investigate whether inappropriate management decisions are being made because the forecasts are being misunderstood. We found more than half the respondents regularly access and use weather and climate forecasts or outlook information from a range of sources and almost three-quarters considered climate information or tools useful, with preferred methods for accessing this information by email, faxback service, internet and the Department of Agriculture Western Australia's Pastoral Memo. Despite differences in enterprise types and rainfall seasonality across the region we found seasonal climate forecasting needs were relatively consistent. It became clear that providing basic training and working with pastoralists to help them understand regional climatic drivers, climate terminology and jargon, and the best ways to apply the forecasts to enhance decision-making are important to improve their use of information. Consideration could also be given to engaging a range of producers to write the climate forecasts themselves in the language they use and understand, in consultation with the scientists who prepare the forecasts.

Antibiotic resistance in Campylobacter jejuni and Campylobacter coli isolated from poultry in the South-East Queensland region

Objectives: The aim of this study was to determine the antimicrobial resistance patterns of 125 Campylobacter jejuni and 27 Campylobacter coli isolates from 39 Queensland broiler farms. Methods: Two methods, a disc diffusion assay and an agar-based MIC assay, were used. The disc diffusion was performed and interpreted as previously described (Huysmans MB, Turnidge JD. Disc susceptibility testing for thermophilic campylobacters. Pathology 1997; 29: 209–16), whereas the MIC assay was performed according to CLSI (formerly NCCLS) methods and interpreted using DANMAP criteria. Results: In both assays, no C. jejuni or C. coli isolates were resistant to ciprofloxacin or chloramphenicol, no C. coli were resistant to nalidixic acid, and no C. jejuni were resistant to erythromycin. In the MIC assay, no C. jejuni isolate was resistant to nalidixic acid, whereas three isolates (2.4%) were resistant in the disc assay. The highest levels of resistance of the C. jejuni isolates were recorded for tetracycline (19.2% by MIC and 18.4% by disc) and ampicillin (19.2% by MIC and 17.6% by disc). The C. coli isolates gave very similar results (tetracycline resistance 14.8% by both MIC and disc; ampicillin resistance 7.4% by MIC and 14.8% by disc). Conclusions: This work has shown that the majority of C. jejuni and C. coli isolates were susceptible to the six antibiotics tested by both disc diffusion and MIC methods. Disc diffusion represents a suitable alternative methodology to agar-based MIC methods for poultry Campylobacter isolates.

Developing African mahogany (Khaya senegalensis) germplasm and its management for a sustainable forest plantation industry in northern Australia: Progress and needs.

The demonstrated wide adaptability, substantial yield potential and proven timber quality of African mahogany (Khaya senegalensis) from plantings of the late 1960s and early 1970s in northern Australia have led to a resurgence of interest in this high-value species. New plantations or trials have been established in several regions since the early 1990s -in four regions in north Queensland, two in the Northern Territory and one in Western Australia. Overall, more than 1500 ha had been planted by early 2007, and the national annual planting from 2007-2008 as currently planned will exceed 2400 ha. Proceedings of two workshops have summarised information available on the species in northern Australia, and suggested research and development (R&D) needs and directions. After an unsustained first phase of domestication of K. senegalensis in the late 1960s to the early 1970s, a second phase began in northern Australia in 2001 focused on conservation and tree improvement that is expected to provide improved planting stock by 2010. Work on other aspects of domestication is also described in this paper: the current estate and plans for extension; site suitability, soils and nutrition; silviculture and management; productivity; pests and diseases; and log and wood properties of a sample of superior trees from two mature plantations of unselected material near Darwin. Some constraints on sustainable plantation development in all these fields are identified and R&D needs proposed. A sustained R&D effort will require a strategic coordinated approach, cooperative implementation and extra funding. Large gains in plantation profitability can be expected to flow from such inputs.

Development of key soil health indicators for the Australian banana industry

To improve the sustainability and environmental accountability of the banana industry there is a need to develop a set of soil health indicators that integrate physical, chemical and biological soil properties. These indicators would allow banana growers, extension and research workers to improve soil health management practices. To determine changes in soil properties due to the cultivation of bananas, a paired site survey was conducted comparing soil properties under conventional banana systems to less intensively managed vegetation systems, such as pastures and forest. Measurements were made on physical, chemical and biological soil properties at seven locations in tropical and sub-tropical banana producing areas. Soil nematode community composition was used as a bioindicator of the biological properties of the soil. Soils under conventional banana production tended to have a greater soil bulk density, with less soil organic carbon (C) (both total C and labile C), greater exchangeable cations, higher extractable P, greater numbers of plant-parasitic nematodes and less nematode diversity, relative to less intensively managed plant systems. The organic banana production systems at two locations had greater labile C, relative to conventional banana systems, but there was no significant change in nematode community composition. There were significant interactions between physical, chemical and nematode community measurements in the soil, particularly with soil C measurements, confirming the need for a holistic set of indicators to aid soil management. There was no single indicator of soil health for the Australian banana industry, but a set of soil health indicators, which would allow the measurement of soil improvements should include: bulk density, soil C, pH, EC, total N, extractable P, ECEC and soil nematode community structure.

Implementation of an electronic nose for continuous odour monitoring in a poultry shed

Continuous odour monitoring technologies are necessary to understand the complex odour-generating mechanisms within poultry housing as well as to identify strategies to reduce the impact of odour emissions on local communities. To evaluate electronic nose (EN) technologies for continuously assessing odour concentration in poultry housing, a mobile laboratory containing an electronic nose and an associated sample delivery system was deployed to a commercial poultry farm and tested over a broiler production cycle. The results demonstrated that it was possible to develop a model to allow an electronic nose to provide a semi-continuous measurement of odour concentrations. The electronic nose was also able to demonstrate the influence of shed conditions on odour emissions.

A generic design environment for the rural industry knowledge acquisition

This paper describes a new knowledge acquisition method using a generic design environment where context-sensitive knowledge is used to build specific DSS for rural business. Although standard knowledge acquisition methods have been applied in rural business applications, uptake remains low and familiar weaknesses such as obsolescence and brittleness apply. We describe a decision support system (DSS) building environment where contextual factors relevant to the end users are directly taken into consideration. This "end user enabled design environment" (EUEDE) engages both domain experts in creating an expert knowledge base and business operators/end users (such as farmers) in using this knowledge for building their specific DSS. We document the knowledge organisation for the problem domain, namely a dairy industry application. This development involved a case-study research approach used to explore dairy operational knowledge. In this system end users can tailor their decision-making requirements using their own judgement to build specific DSSs. In a specific end user's farming context, each specific DSS provides expert suggestions to assist farmers in improving their farming practice. The paper also shows the environment's generic capability.

Analysing industry needs to fine tune IPM project activities

As a first step to better targeting the activities of a project for improving management of western flower thrips, Frankliniella occidentialis, (WFT) in field grown vegetable crops, we surveyed growers, consultants and other agribusiness personnel in two regions of Queensland. Using face-to-face interviews, we collected data on key pests and measures used to manage them, the importance of WFT and associated viral diseases, sources of pest management information and additional skills and knowledge needed by growers and industry. Responses were similar in the two regions. While capsicum growers in one northern Queensland district had suffered serious losses from WFT damage in 2002, in general the pest was not seen as a major problem. In cucurbit crops, the silverleaf whitefly (Bemisia tabaci biotype B) was considered the most difficult insect pest to manage. Pest control tactics were largely based on pesticides although many respondents mentioned non-chemical methods such as good farm hygiene practices, control of weed hosts and regular crop monitoring, particularly when prompted. Respondents wanted to know more about pest identification, biology and damage, spray application and the best use of insecticides. Natural enemies were mentioned infrequently. Keeping up to date with available pesticide options, availability of new chemicals and options for a district-wide approach to managing pests emerged as key issues. Growers identified agricultural distributors, consultants, Queensland Department of Primary Industries staff, other growers and their own experience as important sources of information. Field days, workshops and seminars did not rank highly. Busy vegetable growers wanted these activities to be short and relevant, and preferred to be contacted by post and facsimile rather than email. In response to these results, we are focusing on three core, interrelated project extension strategies: (i) short workshops, seminars and farm walks to provide opportunities for discussion, training and information sharing with growers and their agribusiness advisors; (ii) communication via newsletters and information leaflets; (iii) support for commercialisation of services.

Pitfalls and benefits of involving industry in fisheries research: A case study of the live reef fish industry in Queensland, Australia

Including collaboration with industry members as an integral part of research activities is a relatively new approach to fisheries research. Earlier approaches to involving fishers in research usually involved compulsory accommodations of research, such as through compulsory observer programs, in which fishers were seen as subjects of rather than participants in research. This new approach brings with it significant potential benefits but also some unique issues both for the researchers and the participating industry members. In this paper we describe a research project involving the Queensland Coral Reef Finfish Fishery that originated from industry and community concerns about changes in marketing practices in an established commercial line fishery. A key aspect of this project was industry collaboration in all stages of the research, from formulation of objectives to assistance with interpretation of results. We discuss this research as a case study of some of the issues raised by collaboration between industry and research groups in fisheries research and the potential pitfalls and benefits of such collaborations for all parties. A dedicated liaison and extension strategy was a key element in the project to develop and maintain the relationships between fishers and researchers that were fundamental to the success of the collaboration. A major research benefit of the approach was the provision of information not available from other sources: 300 days of direct and unimpeded observation of commercial fishing by researchers; detailed catch and effort records from a further 126 fishing trips; and 53 interviews completed with fishers. Fishers also provided extensive operational information about the fishery as well as ongoing support for subsequent research projects. The time and resources required to complete the research in this consultative framework were greater than for more traditional, researcher-centric fisheries research, but the benefits gained far outweighed the costs.