Diel variation in mangrove fish abundances and trophic guilds of northeastern Australian estuaries with a proposed trophodynamic model

Diel activity patterns of tropical fish assemblages in turbid, mangrove-dominated estuaries remain largely undocumented, leading to uncertainty about ecological processes in these systems. To capture active fishes by day and night, gill nets were set perpendicular to mangrove shorelines, in six northeastern Australian estuaries during 13 bimonthly trips. Fish were sampled with eight large mesh (102-151 mm) nets, set for 6 hrs (1500-2100), and checked hourly (1146 day, 635 dusk, 872 night checks). Four smaller mesh (19-51 mm) nets were also set for 1 hr before and after sunset (77 day, 78 night checks). Of 157 total species, 22 were netted exclusively before sunset and 47 exclusively after sunset. All of the top 26 species were present both day and night, but of these, 46% were primarily nocturnal (diel index > 0.65). An average of 77.2 fish hr−1 were netted by day vs 171.4 by night. Within the 400 km coastal region, assemblages differed between two northern wave-dominated (WD) estuaries and four southern tide-dominated ('I'D) estuaries. In all six estuaries Lates calcarifer (Bloch, 1790) dominated night assemblages. In 'I'D estuaries, night assemblages were also dominated by Thryssa hamiltoni Gray, 1835 and Eleutheronema tetradactylum (Shaw, 1804); while in WD estuaries Herklotsichthys castelnaui (Ogilby, 1897), Leiognathus equulus (Forsskål, 1775), and Megalops cyprinoids (Broussonet, 1782) were dominant at night. Nocturnal species included planktivores and carnivores, while daytime assemblages were dominated by detritivores (Mugillidae). Higher night catch rates are attributed to increased activity by mobile fishes moving from mangrove to adjacent habitats to forage, especially immediately post-sunset. Although day-night diets and forage resources have yet to be compared in mangrove systems, previously unrecognized trophic relationships involving variation in diel activity among important fishery species (Centropomidae, polynemidae, Carangidae) and their prey may be key ecological processes in these tropical mangrove estuaries. A proposed hypothesis explaining diel variation in mangrove fish assemblages of tropical estuaries is presented through a conceptual model.

Potential for using through-boring to improve groundline treatment of Australian wood species: A preliminary study.

An aging electricity distribution system and reduced availability of naturally durable tropical hardwoods in Australia will combine in the next decade to produce a major shortage of poles. One approach to mitigating this shortage is to utilize lower durability species and improve the penetration of preservatives into the refractory heartwood by introducing additional pretreatment processes. A potential method for improving preservative penetration in the critical ground-line zone is through-boring. This process, in which holes are drilled through the pole perpendicular to the grain in the ground-line zone, is widely used in the western United States for treatment of Douglas-fir and may be Suitable for many Australian wood species. The potential for improving heartwood penetration in eucalypts with alkaline-copper-quaternary (ACQ) compound was assessed on heartwood specimens from four species (Eucalyptus cloeziana F.Muell., E. grandis W.Hill ex Maiden, E. obliqua L'Her. and E. pellita F.Muell.) and Lophostemon confertus (R.Br.) Peter G.Wilson & J.T.Wateril). Longitudinal ACQ penetration was extremely shallow in L. confertus and only slightly better in E. cloeziana. Longitudinal penetration was good in both E. obliqua and E. pellita, although there was some variation in treatment results with length of pressure period. The results suggest that through-boring might be a reasonable approach for achieving heartwood penetration in some Eucalyptus species, although further studies are required to assess additional treatment schedules and to determine the effects of the process oil flexural properties of the poles.

Identification of intersectional Corymbia hybrids based on seedling morphology improves with parental divergence

Differences in morphology have provided a basis for detecting natural interspecific hybridisation in forest trees for decades but have come to prominence again more recently as a means for directly measuring gene flow from planted forests. Here we examined the utility of seedling morphology for hybrid discrimination in three hybrid groups relevant to the monitoring of gene flow from plantings of Corymbia (L.D. Pryor & L.A.S. Johnson ex Brooker) taxa in subtropical Australia. Thirty leaf and stem characters were assessed on 907 8-month old seedlings from four parental and six hybrid taxa grown in a common garden. Outbred F1 hybrids between spotted gums (Corymbia citriodora subspecies variegata, C. citriodora subspecies citriodora and Corymbia henryi) tended to more closely resemble their maternal Corymbia torelliana parent and the most discriminating characters were the ratio of blade length to maximum perpendicular width, the presence or absence of a lignotuber, and specific leaf weight. Assignment of individuals into genealogical classes based on a multivariate model limited to a set of the more discriminating and independent characters was highest in the hybrid group, where parental taxa were genetically most divergent. Overall power to resolve among outbred F1 hybrids from both parental taxa was low to moderate, but this may not be a limitation to its likely major application of identifying hybrids in seedlots from native spotted gum stands. Advanced generation hybrids (outbred F2 and outbred backcrosses) were more difficult to resolve reliably due to the higher variances of hybrid taxa and the tendency of backcrosses to resemble their recurrent parents. Visual assessments of seedling morphology may provide a filter allowing screening of the large numbers needed to monitor gene flow, but will need to be combined with other hybrid detection methods to ensure hybrids are detected.

Thin-walled timber and FRP-timber veneer composite CEE-sections

This paper compares the structural performance between thin-walled timber and FRP-timber composite Cee-sections. While, thin-walled composite timber structures have been proven to be efficient and ultra-light structural elements, their manufacturing is difficult and labour intensive. Significant effort and time is required to prevent the cracking of the transverse timber veneers, bent in the grain direction, when forming the cross-sectional shape. FRP-timber structures overcome this disadvantage by replacing the transverse veneers with flexible, unidirectional FRP material and only keeping the timber veneers which are bent in their natural rolling direction. The Cee-sections investigated in this study were 210 mm deep × 90 mm wide × 500 mm high and manufactured from five plies. For both section types, the three internal plies were thin (1 mm thick) softwood Hoop pine (Araucaria cunninghamii) veneers, orientated along the section longitudinal axis. The two outer layers, providing bending stiffness to the walls, were Hoop pine veneers (1 mm thick) for the timber sections and glass fibre reinforced plastic (0.73 mm thick) for the FRP-timber sections orientated perpendicular to the inner layers. The manufacturing process is briefly introduced in this paper. The profiles were fitted with strain gauges and tested in compression. Linear Variable Displacement Transducers also recorded the buckling along one flange. The test results are presented and discussed in this paper in regards to their structural behaviour and performance. Results showed that the use of FRP in the sections increases both the elastic local buckling load and section capacity, the latter being increased by about 24 percent. The results indicate that thin-walled FRP-timber can ultimately be used as a sustainable alternative to cold-formed steel profiles.

Characterisation of wood–water relationships and transverse anatomy and their relationship to drying degrade

Characterisation of a number of key wood properties utilising ‘state of the art’ tools was achieved for four commercial Australian hardwood species: Corymbia citriodora, Eucalyptus pilularis, Eucalyptus marginata and Eucalyptus obliqua. The wood properties were measured for input into microscopic (cellular level) and macroscopic (board level) vacuum drying models currently under development. Morphological characterisation was completed using a combination of ESEM, optical microscopy and a custom vector-based image analysis software. A clear difference in wood porosity, size, wall thickness and orientation was evident between species. Wood porosity was measured using a combination of fibre and vessel porosity. A highly sensitive microbalance and scanning laser micrometres were used to measure loss of moisture content in conjunction with directional shrinkage on micro-samples of E. obliqua to investigate the validity of measuring collapse-free shrinkage in very thin sections. Collapse-free shrinkage was characterised, and collapse propensity was verified when testing thicker samples. Desorption isotherms were calculated for each species using wood–water relations data generated from shrinkage experiments. Fibre geometry and wood shrinkage anisotropy were used to explain the observed difficulty in drying of the different species in terms of collapse and drying stress-related degrade.