Characterisation of wood properties and transverse anatomy for vacuum drying modelling of commercially important Australian hardwood species.

Characterisation and investigation of a number of key wood properties, critical for further modelling work, has been achieved. The key results were: • Morphological characterisation, in terms of fibre cell wall thickness and porosity, was completed. A clear difference in fibre porosity, size, wall thickness and orientation was evident between species. Results were consistent with published data for other species. • Viscoelastic properties of wood were shown to differ greatly between species and in the radial and tangential directions, largely due to anatomical and chemical variations. Consistent with published data, the radial direction shows higher stiffness, internal friction and glass transition temperature than the tangential directions. The loss of stiffness over the measured temperature range was greater in the tangential direction than the radial direction. Due to time dependant molecular relaxation, the storage modulus and glass transition temperature decreased with decreasing test frequency, approaching an asymptotic limit. Thus the viscoelastic properties measured at lower frequencies are more representative of static material. • Dynamic interactions between relative humidity, moisture content and shrinkage of four Australian hardwood timbers can be accurately monitored on micro-samples using a specialised experimental device developed by AgroParisTech – ENGREF. The device generated shrinkage data that varied between species but were consistent (repeatable) within a species. Collapse shrinkage was clearly evident with this method for Eucalyptus obliqua, but not with other species, consistent with industrial seasoning experience. To characterise the wood-water relations of this species, free of collapse, thinner sample sections (in the R-T plane) should be used.

Drought adaptation of stay-green sorghum is associated with canopy development, leaf anatomy, root growth, and water uptake

Stay-green sorghum plants exhibit greener leaves and stems during the grain-filling period under water-limited conditions compared with their senescent counterparts, resulting in increased grain yield, grain mass, and lodging resistance. Stay-green has been mapped to a number of key chromosomal regions, including Stg1, Stg2, Stg3, and Stg4, but the functions of these individual quantitative trait loci (QTLs) remain unclear. The objective of this study was to show how positive effects of Stg QTLs on grain yield under drought can be explained as emergent consequences of their effects on temporal and spatial water-use patterns that result from changes in leaf-area dynamics. A set of four Stg near-isogenic lines (NILs) and their recurrent parent were grown in a range of field and semicontrolled experiments in southeast Queensland, Australia. These studies showed that the four Stg QTLs regulate canopy size by: (1) reducing tillering via increased size of lower leaves, (2) constraining the size of the upper leaves; and (3) in some cases, decreasing the number of leaves per culm. In addition, they variously affect leaf anatomy and root growth. The multiple pathways by which Stg QTLs modulate canopy development can result in considerable developmental plasticity. The reduction in canopy size associated with Stg QTLs reduced pre-flowering water demand, thereby increasing water availability during grain filling and, ultimately, grain yield. The generic physiological mechanisms underlying the stay-green trait suggest that similar Stg QTLs could enhance post-anthesis drought adaptation in other major cereals such as maize, wheat, and rice.

Stem anatomy and adventitious root formation in cuttings of Angophora, Corymbia and Eucalyptus

Many plantation eucalypts are difficult to propagate from cuttings, and their rooted cuttings often possess very few adventitious roots. We microscopically examined the stem anatomy of cuttings from 12 species of eucalypts and we determined whether adventitious root formation in auxin-treated cuttings of four species was limited to particular positions around the vascular tissue. Most species contained a central pith that was arranged in a four-pointed stellate pattern. The surrounding vascular tissue was also arranged in a stellate pattern near the shoot apex but it developed a more rectangular shape at the outer phloem as the stems enlarged radially. Adventitious roots formed at, or slightly peripheral to, the vascular cambium, and they formed at both the corners and the sides of the rectangular-shaped vascular tissue. The study highlighted that auxin-treated eucalypt cuttings can produce roots at multiple positions around the vascular tissue and so propagation methods can aim to produce more than four adventitious roots per rooted cutting. Higher numbers of adventitious roots could improve the root system symmetry, stability, survival and growth rate of clonal eucalypt trees. © 2015 by the authors; licensee MDPI, Basel, Switzerland.

Characterisation of wood–water relationships and transverse anatomy and their relationship to drying degrade

Characterisation of a number of key wood properties utilising ‘state of the art’ tools was achieved for four commercial Australian hardwood species: Corymbia citriodora, Eucalyptus pilularis, Eucalyptus marginata and Eucalyptus obliqua. The wood properties were measured for input into microscopic (cellular level) and macroscopic (board level) vacuum drying models currently under development. Morphological characterisation was completed using a combination of ESEM, optical microscopy and a custom vector-based image analysis software. A clear difference in wood porosity, size, wall thickness and orientation was evident between species. Wood porosity was measured using a combination of fibre and vessel porosity. A highly sensitive microbalance and scanning laser micrometres were used to measure loss of moisture content in conjunction with directional shrinkage on micro-samples of E. obliqua to investigate the validity of measuring collapse-free shrinkage in very thin sections. Collapse-free shrinkage was characterised, and collapse propensity was verified when testing thicker samples. Desorption isotherms were calculated for each species using wood–water relations data generated from shrinkage experiments. Fibre geometry and wood shrinkage anisotropy were used to explain the observed difficulty in drying of the different species in terms of collapse and drying stress-related degrade.

Genotypic variation in seedling root architectural traits and implications for drought adaptation in wheat (Triticum aestivum L.)

Root system characteristics are of fundamental importance to soil exploration and below-ground resource acquisition. Root architectural traits determine the in situ space-filling properties of a root system or root architecture. The growth angle of root axes is a principal component of root system architecture that has been strongly associated with acquisition efficiency in many crop species. The aims of this study were to examine the extent of genotypic variability for the growth angle and number of seminal roots in 27 current Australian and 3 CIMMYT wheat (Triticum aestivum L.) genotypes, and to quantify using fractal analysis the root system architecture of a subset of wheat genotypes contrasting in drought tolerance and seminal root characteristics. The growth angle and number of seminal roots showed significant genotypic variation among the wheat genotypes with values ranging from 36 to 56 (degrees) and 3 to 5 (plant-1), respectively. Cluster analysis of wheat genotypes based on similarity in their seminal root characteristics resulted in four groups. The group composition reflected to some extent the genetic background and environmental adaptation of genotypes. Wheat cultivars grown widely in the Mediterranean environments of southern and western Australia generally had wider growth angle and lower number of seminal axes. In contrast, cultivars with superior performance on deep clay soils in the northern cropping region, such as SeriM82, Baxter, Babax, and Dharwar Dry exhibited a narrower angle of seminal axes. The wheat genotypes also showed significant variation in fractal dimension (D). The D values calculated for the individual segments of each root system suggested that, compared to the standard cultivar Hartog, the drought-tolerant genotypes adapted to the northern region tended to distribute relatively more roots in the soil volume directly underneath the plant. These findings suggest that wheat root system architecture is closely linked to the angle of seminal root axes at the seedling stage. The implications of genotypic variation in the seminal root characteristics and fractal dimension for specific adaptation to drought environment types are discussed with emphasis on the possible exploitation of root architectural traits in breeding for improved wheat cultivars for water-limited environments.

The role of root architectural traits in adaptation of wheat to water-limited environments

Better understanding of root system structure and function is critical to crop improvement in water-limited environments. The aims of this study were to examine root system characteristics of two wheat genotypes contrasting in tolerance to water limitation and to assess the functional implications on adaptation to water-limited environments of any differences found. The drought tolerant barley variety, Mackay, was also included to allow inter-species comparison. Single plants were grown in large, soil-filled root-observation chambers. Root growth was monitored by digital imaging and water extraction was measured. Root architecture differed markedly among the genotypes. The drought-tolerant wheat (cv. SeriM82) had a compact root system, while roots of barley cv. Mackay occupied the largest soil volume. Relative to the standard wheat variety (Hartog), SeriM82 had a more uniform rooting pattern and greater root length at depth. Despite the more compact root architecture of SeriM82, total water extracted did not differ between wheat genotypes. To quantify the value of these adaptive traits, a simulation analysis was conducted with the cropping system model APSIM, for a wide range of environments in southern Queensland, Australia. The analysis indicated a mean relative yield benefit of 14.5% in water-deficit seasons. Each additional millimetre of water extracted during grain filling generated an extra 55 kg ha-1 of grain yield. The functional implications of root traits on temporal patterns and total amount of water capture, and their importance in crop adaptation to specific water-limited environments, are discussed.

Determination of specific leaf area of some commercially useful sub-tropical hardwood species

Variability of specific leaf area (SLA) across taxa, sites and crown zones was determined for four sub-tropical hardwood species, Eucalyptus grandis, E. cloeziana, E. argophloia and Corymbia citriodora ssp. variegata, growing in south-eastern Queensland. Mean SLA values were stable amongst those taxa sampled on dry sites but varied markedly between provenances of E. grandis on a moist site. Mean SLA did not vary significantly with crown zone in any of these four sub-tropical eucalypts, which is in contrast to that observed in temperate species, both in Australia and overseas. A provenance of E. cloeziana from a moist coastal site exhibited the largest SLA of all taxa studied.

Post capture necrosis of the feet caused by soft-catch traps – incidents, cause and prevention.

When recapturing satellite collared wild dogs that had been trapped one month previous in padded foothold traps, we noticed varying degrees of pitting on the pads of their trapped paw. Veterinary advice, based on images taken of the injuries, suggests that the necrosis was caused by vascular compromise. Five of six dingoes we recaptured had varying degrees of necrosis restricted only to the trapped foot and ranging from single 5 mm holes to 25% sections of the toe pads missing or deformed, including loss of nails. The traps used were rubber-padded, two–coiled, Victor Soft Catch #3 traps. The springs are not standard Victor springs but were Beefer springs; these modifications slightly increase trap speed and the jaw pressure on the trapped foot. Despite this modification the spring pressure is still relatively mild in comparison to conventional long spring or four-coiled wild dog traps. The five wild dogs developing necrosis were trapped in November 2006 at 5-6 months of age. Traps were checked each morning so the dogs were unlikely to have been restrained in the trap for more than 12 hours. All dogs exhibited a small degree of paw damage at capture which presented itself as a swollen paw and compression at the capture point. In contrast, eight wild dogs, 7-8 month-old, were captured two months later in February. Upon their release, on advice from a veterinarian, we massaged the trapped foot to get blood flow back in to the foot and applied a bruise treatment (Heparinoid 8.33 mg/ml) to assist restoring blood flow. These animals were subsequently recaptured several months later and showed no signs of necrosis. While post-capture foot injuries are unlikely to be an issue in conventional control programs where the animal is immediately destroyed, caution needs to be used when releasing accidentally captured domestic dogs or research animals captured in rubber-padded traps. We have demonstrated that 7-8 month old dogs can be trapped and released without any evidence of subsequent necrosis following minimal veterinary treatment. We suspect that the rubber padding on traps may increase the tourniquet effect by wrapping around the paw and recommend the evaluation of offset laminated steel jaw traps as an alternative. Offset laminated steel jaw traps have been shown to be relatively humane producing as few foot injuries as rubber-jawed traps.

FWPA Cullity Fellowship AR Redman

FWPA Cullity Fellowship research program - Characterisation of wood properties and transverse anatomy for vacuum drying modelling of commercially important Australian hardwood species.

Male traits and herd reproductive capability in tropical beef cattle. 1. Experimental design and animal measures

Research into the genetics of whole herd profitability has been a focus of the Beef Cooperative Research Centre for Beef Genetic Technologies over the past decade and it has been identified that measures of male reproduction may offer a potential indirect means of selecting for improved female reproduction. This paper describes the experimental design and provides a descriptive analysis of an array of male traits in Brahman and Tropical Composite genotypes managed under the medium to high stress, semi-extensive to extensive production systems of northern Australia. A total of 1639 Brahman and 2424 Tropical Composite bulls with known pedigrees, bred and raised in northern Australia, were evaluated for a comprehensive range of productive and reproductive traits. These included blood hormonal traits (luteinising hormone, inhibin and insulin-like growth factor-I); growth and carcass traits (liveweight, body condition score, ultrasound scanned 12-13th rib fat, rump P8 fat, eye muscle area and hip height); adaptation traits (flight time and rectal temperature); and a bull breeding soundness evaluation (leg and hoof conformation, sheath score, length of everted prepuce, penile anatomy, scrotal circumference, semen mass activity, sperm motility and sperm morphology). Large phenotypic variation was evident for most traits, with complete overlap between genotypes, indicating that there is likely to be a significant opportunity to improve bull fertility traits through management and bull selection.

Reducing the incidence of under-skin browning in 'Honey Gold' mango (Mangifera indica L.) fruit

'Honey Gold' mango is a relatively new cultivar in Australia, with an appealing skin colour and a sweet fibre-free flesh. However, fruit can develop 'under-skin browning' (USB), which appears several days after packing as a distinct 'bruise'-like discolouration under the epidermis and can affect large areas of the fruit surface. We investigated the anatomy of USB and the impact of post-harvest fruit handling conditions on the disorder. Starch accumulated around the resin canals and discoloured cells in the affected area, with no visible change to the cuticle or epidermis. Delays of 1 d at ambient temperature (27 degrees - 35 degrees C) before packing, and 2 d at 18 degrees - 20 degrees C (after packing), before placing fruit at 12 degrees - 14 degrees C and road transportation, reduced the incidence of USB by 83% compared to placing fruit at 12 degrees - 14 degrees C within 13 h of picking. The incidence of USB was 88 100% higher in fruit that were cooled to 12 degrees - 14 degrees C within 13 h of picking, then commercially road-freighted for 4 d at 12 degrees - 14 degrees C, than in fruit held under similar temperature conditions, but not road-freighted. Wrapping each fruit in bubble-wrap to minimise direct contact with other fruit, with the plastic insert, or with the cardboard tray, reduced the incidence of USB by 84% after road-freight compared to not using bubble-wrap. These results suggest that USB is a unique disorder of mango skin associated with a rapid post-harvest reduction in temperature, from high ambient temperatures to 12 degrees - 14 degrees C, and with physical damage during road-freight.

Variation in leaf structure of the invasive Madeira vine (Anredera cordifolia, Basellaceae) at different light levels

Madeira vine (Anredera cordifolia (Ten.) Steenis) is a climber in the angiosperm family Basellaceae. It is native to South America and has naturalised in Australia. It is regarded as a serious environmental weed because of the structural damage it causes to native vegetation. The present study, for the first time, documents anatomical and morphological traits of the leaves of A. cordifolia and considers their implications for its ecology and physiology. Plants were grown under three different light levels, and anatomical and morphological leaf characters were compared among light levels, among cohorts, and with documented traits of the related species, Basella alba L. Stomata were present on both the adaxial and abaxial sides of the leaf, with significantly more stomata on the abaxial side and under high light. This may account for the ability of this species to fix large amounts of carbon and rapidly respond to light gaps. The leaves had very narrow veins and no sclerenchyma, suggesting a low construction cost that is associated with invasive plants. There was no significant difference in any of the traits among different cohorts, which agrees with the claim that A. cordifolia primarily propagates vegetatively. The anatomy and morphology of A. cordifolia was similar to that of B. alba.

Coordination and plasticity in leaf anatomical traits of invasive and native vine species

Premise of the study: Plant invasiveness can be promoted by higher values of adaptive traits (e.g., photosynthetic capacity, biomass accumulation), greater plasticity and coordination of these traits, and by higher and positive relative influence of these functionalities on fitness, such as increasing reproductive output. However, the data set for this premise rarely includes linkages between epidermal–stomatal traits, leaf internal anatomy, and physiological performance.• Methods: Three ecological pairs of invasive vs. noninvasive (native) woody vine species of South-East Queensland, Australia were investigated for trait differences in leaf morphology and anatomy under varying light intensity. The linkages of these traits with physiological performance (e.g., water-use efficiency, photosynthesis, and leaf construction cost) and plant adaptive traits of specific leaf area, biomass, and relative growth rates were also explored.• Key results: Except for stomatal size, mean leaf anatomical traits differed significantly between the two groups. Plasticity of traits and, to a very limited extent, their phenotypic integration were higher in the invasive relative to the native species. ANOVA, ordination, and analysis of similarity suggest that for leaf morphology and anatomy, the three functional strategies contribute to the differences between the two groups in the order phenotypic plasticity > trait means > phenotypic integration.• Conclusions: The linkages demonstrated in the study between stomatal complex/gross anatomy and physiology are scarce in the ecological literature of plant invasiveness, but the findings suggest that leaf anatomical traits need to be considered routinely as part of weed species assessment and in the worldwide leaf economic spectrum.