Validation of single photon absorptiometry for on-farm measurement of density and mineral content of tail bone in cattle

A validation study examined the accuracy of a purpose-built single photon absorptiometry (SPA) instrument for making on-farm in vivo measurements of bone mineral density (BMD) in tail bones of cattle. In vivo measurements were made at the proximal end of the ninth coccygeal vertebra (Cy9) in steers of two age groups (each n = 10) in adequate or low phosphorus status. The tails of the steers were then resected and the BMD of the Cy9 bone was measured in the laboratory with SPA on the resected tails and then with established laboratory procedures on defleshed bone. Specific gravity and ash density were measured on the isolated Cy9 vertebrae and on 5-mm2 dorso-ventral cores of bone cut from each defleshed Cy9. Calculated BMD determined by SPA required a measure of tail bone thickness and this was estimated as a fraction of total tail thickness. Actual tail bone thickness was also measured on the isolated Cy9 vertebrae. The accuracy of measurement of BMD by SPA was evaluated by comparison with the ash density of the bone cores measured in the laboratory. In vivo SPA measurements of BMD were closely correlated with laboratory measurements of core ash density (r = 0.92). Ash density and specific gravity of cores, and all SPA measures of BMD, were affected by phosphorus status of the steers, but the effect of steer age was only significant (P < 0.05) for steers in adequate phosphorus status. The accuracy of SPA to determine BMD of tail bone may be improved by reducing error associated with in vivo estimation of tail bone thickness, and also by adjusting for displacement of soft tissue by bone mineral. In conclusion a purpose-built SPA instrument could be used to make on-farm sequential non-invasive in vivo measurements of the BMD of tailbone in cattle with accuracy acceptable for many animal studies.

Postharvest handling practices and irradiation increase lenticel discolouration in ‘B74’ mango fruit

ABSTRACT 'B74' mango is a recently commercialised cultivar in Australia, with an appealing skin colour and firm fibreless flesh. However, fruit can develop lenticel discolouration (LD) after harvest, with loss of commercial value, especially after γ-irradiation as a disinfestation treatment. We hypothesised that postharvest practices could increase fruit sensitivity to LD and tested that by sequentially sampling fruit between the orchard and the end of the packing line over two seasons, followed by ripening without and with irradiation treatment. Exposure of 441-610 Gy γ-irradiation significantly increased the severity of LD by 6.8-fold in commercially picked and packed ripe fruit, reducing the proportion of marketable fruit from 98% to 2%, compared to irradiated fruit harvested directly from the trees and not exposed to de-sapping solution and packing operations. Also, LD increased progressively as the fruit passed through the harvesting and packing processes, and exposure to only bore water increased LD severity compared with no water contact. Results suggest that the typical de-sapping process used during harvesting is a major contributor to skin sensitivity to LD in 'B74' mango fruit, and that other packing operations involving wetting of the fruit have an additive effect on it. These effects are exacerbated if fruit is irradiated.

Quality of handling and holding yard environment, and beef cattle temperament: 1. Relationships with flight speed and fear of humans.

Numerous tests have been used to measure beef cattle temperament, but limited research has addressed the relationship between such tests and whether temperament can be modified. One-hundred-and-forty-four steers were given one of three human handling and yarding experiences on six occasions during a 12-month grazing period post-weaning (backgrounding): Good handling/yarding, Poor handling/yarding and Minimal handling/yarding. At the end of this phase the cattle were lot-fed for 78 days, with no handling/yarding treatments imposed, before being transported for commercial slaughter. Temperament was assessed at the start of the experiment, during backgrounding and lot-feeding by flight speed (FS) and a fear of humans test, which measured the proximity to a stimulus person (zone average; ZA), the closest approach to the person (CA) and the amount the cattle moved around the test arena (total transitions; TT). During backgrounding, FS decreased for all treatments and at the end of backgrounding there was no difference between them. The rate of decline, however, was greatest in the Good group, smallest in the Minimal group with the Poor intermediate. In contrast, ZA was affected by treatment, with a greater reduction for the Good group than the others (P = 0.012). During lot-feeding, treatment did not affect FS, but all groups showed a decrease in ZA, with the greatest change in the Poor group, the least in the Good and the Minimal intermediate (P = 0.052). CA was positively correlated with ZA (r = 0.18 to 0.66) and negatively with TT (r = -0.180 to -0.659). FS was consistently correlated with TT only (r = 0.17 to 0.49). These findings suggest that FS and TT measure a similar characteristic, as do ZA and CA, but that these characteristics are different from one another, indicating that temperament is not a unitary trait, but has different facets. FS and TT measure one facet that we suggest is general agitation, whilst ZA and CA measure fear of people. Thus, the cattle became less agitated during backgrounding, but the effect was not permanently influenced by the quantity and quality of handling/yarding. However, Good handling/yarding reduced fearfulness of people. Fear of people was also reduced during lot-feeding, probably as a consequence of frequent exposure to humans in a situation that was neutral or positive for the cattle.

Best management practices for sustainable and safe playing surface of Australian Football League sports fields

In 2002, AFL Queensland and the Brisbane Lions Football Club approached the Department of Primary Industries and Fisheries (Queensland) for advice on improving their Premier League sports fields. They were concerned about player safety and dissatisfaction with playing surfaces, particularly uneven turf cover and variable under-foot conditions. They wanted to get the best from new investments in ground maintenance equipment and irrigation infrastructure. Their sports fields were representative of community-standard, multi-use venues throughout Australia; generally ‘natural’ soil fields, with low maintenance budgets, managed by volunteers. Improvements such as reconstruction, drainage, or regular re-turfing are generally not affordable. Our project aimed to: (a) Review current world practice and performance benchmarks; (b) Demonstrate best-practice management for community-standard fields; (c) Adapt relevant methods for surface performance testing; (d) Assess current soils, and investigate useful amendments; (e) Improve irrigation system performance; and (e) Build industry capacity and encourage patterns for ongoing learning. Most global sports field research focuses on elite, sand-based fields. We adjusted elite standards for surface performance (hardness, traction, soil moisture, evenness, sward cover/height) and maintenance programs, to suit community-standard fields with lesser input resources. In regularly auditing ground conditions across 12 AFLQ fields in SE QLD, we discovered surface hardness (measured by Clegg Hammer) was the No. 1 factor affecting player safety and surface performance. Other important indices were turf coverage and surface compaction (measured by penetrometer). AFLQ now runs regularly audits affiliated fields, and closes grounds with hardness readings greater than 190 Gmax. Aerating every two months was the primary mechanical practice improving surface condition and reducing hardness levels to < 110 Gmax on the renovated project fields. With irrigation installation, these fields now record surface conditions comparable to elite fields. These improvements encouraged many other sporting organisations to seek advice / assistance from the project team. AFLQ have since substantially invested in an expanded ground improvement program, to cater for this substantially increased demand. In auditing irrigation systems across project fields, we identified low maintenance (with < 65% of sprinklers operating optimally) as a major problem. Retrofitting better nozzles and adjusting sprinklers improved irrigation distribution uniformity to 75-80%. Research showed that reducing irrigation frequency to weekly, and preparedness to withhold irrigation longer after rain, reduced irrigation requirement by 30-50%, compared to industry benchmarks of 5-6 ML/ha/annum. Project team consultation with regulatory authorities enhanced irrigation efficiency under imposed regional water restrictions. Laboratory studies showed incorporated biosolids / composts, or topdressed crumb rubber, improved compaction resistance of soils. Field evaluations confirmed compost incorporation significantly reduced surface hardness of high wear areas in dry conditions, whilst crumb rubber assisted turf persistence into early winter. Neither amendment was a panacea for poor agronomic practices. Under the auspices of the project Trade Mark Sureplay®, we published > 80 articles, and held > 100 extension activities involving > 2,000 participants. Sureplay® has developed a multi-level curator training structure and resource materials, subject to commercial implementation. The partnerships with industry bodies (particularly AFLQ), frequent extension activities, and engagement with government/regulatory sectors have been very successful, and are encouraged for any future work. Specific aspects of sports field management for further research include: (a) Understanding of factors affecting turf wear resistance and recovery, to improve turf persistence under wear; (b) Simple tests for pinpointing areas of fields with high hardness risk; and (c) Evaluation of new irrigation infrastructure, ‘water-saving’ devices, and irrigation protocols, in improving water use and turf cover outcomes.

Construction, installation, and performance of two repacked weighing lysimeters

Weighing lysimeters are the standard method for directly measuring evapotranspiration (ET). This paper discusses the construction, installation, and performance of two (1.52 m × 1.52 m × 2.13-m deep) repacked weighing lysimeters for measuring ET of corn and soybean in West Central Nebraska. The cost of constructing and installing each lysimeter was approximately US $12,500, which could vary depending on the availability and cost of equipment and labor. The resolution of the lysimeters was 0.0001 mV V-1, which was limited by the data processing and storage resolution of the datalogger. This resolution was equivalent to 0.064 and 0.078 mm of ET for the north and south lysimeters, respectively. Since the percent measurement error decreases with the magnitude of the ET measured, this resolution is adequate for measuring ET for daily and longer periods, but not for shorter time steps. This resolution would result in measurement errors of less than 5% for measuring ET values of ≥3 mm, but the percent error rapidly increases for lower ET values. The resolution of the lysimeters could potentially be improved by choosing a datalogger that could process and store data with a higher resolution than the one used in this study.

Improving knowledge and practices in fresh produce chains

A successful supply chain must delivery the right product, value and satisfaction to the end customer, and profitability for its participants. Critical to getting the product right is the practices used to produce and maintain product quality through the supply chain from production to sale to the end customer. This paper describes the approach used by a R&D team to add value to supply chains through improving knowledge and practices. The desired outcome is better produce quality for consumers and more control and less wastage for chain participants. The team worked with specific supply chains to identify areas for improvement and to develop, test and implement improved practices. The knowledge gained was communicated to the industry to gain wider adoption of results. Three conditions were identified as critical for practice change - motivation, knowledge, and capacity for change. For improvement in practices to occur, a business must be motivated and have the knowledge and capacity to improve. Two case studies of working with Australian supply chains (mango and melons) are presented to illustrate our participatory methodology. A key activity is monitoring produce quality and handling practices and conditions to demonstrate to participants the points where quality deterioration occurs in the supply chain. This participatory approach is successful because working with supply chain participants generates knowledge and solutions to real problems. It enables the participants to observe the effect of handling practices and conditions on produce quality, gain knowledge and assess the benefits of improvements. Where existing knowledge is not present, research is conducted to fill the knowledge gaps. IV International Conference on Managing Quality in Chains - The Integrated View on Fruits and Vegetables Quality

The distribution and spread of citrus canker in Emerald, Australia

Citrus canker is a disease of citrus and closely related species, caused by the bacterium Xanthomonas citri subsp. citri. This disease, previously exotic to Australia, was detected on a single farm [infested premise-1, (IP1). IP is the terminology used in official biosecurity protocols to describe a locality at which an exotic plant pest has been confirmed or is presumed to exist. IP are numbered sequentially as they are detected] in Emerald, Queensland in July 2004. During the following 10 months the disease was subsequently detected on two other farms (IP2 and IP3) within the same area and studies indicated the disease first occurred on IP1 and spread to IP2 and IP3. The oldest, naturally infected plant tissue observed on any of these farms indicated the disease was present on IP1 for several months before detection and established on IP2 and IP3 during the second quarter (i.e. autumn) 2004. Transect studies on some IP1 blocks showed disease incidences ranged between 52 and 100% (trees infected). This contrasted to very low disease incidence, less than 4% of trees within a block, on IP2 and IP3. The mechanisms proposed for disease spread within blocks include weather-assisted dispersal of the bacterium (e.g. wind-driven rain) and movement of contaminated farm equipment, in particular by pivot irrigator towers via mechanical damage in combination with abundant water. Spread between blocks on IP2 was attributed to movement of contaminated farm equipment and/or people. Epidemiology results suggest: (i) successive surveillance rounds increase the likelihood of disease detection; (ii) surveillance sensitivity is affected by tree size; and (iii) individual destruction zones (for the purpose of eradication) could be determined using disease incidence and severity data rather than a predefined set area.

MOE and MOR assessment technologies for improving graded recovery of exotic pines in Australia.

This project was designed to provide the structural softwood processing industry with the basis for improved green and dry grading to allow maximise MGP grade yields, consistent product performance and reduced processing costs. To achieve this, advanced statistical techniques were used in conjunction with state-of-the-art property measurement systems. Specifically, the project aimed to make two significant steps forward for the Australian structural softwood industry: • assessment of technologies, both existing and novel, that may lead to selection of a consistent, reliable and accurate device for the log yard and green mill. The purpose is to more accurately identify and reject material that will not make a minimum grade of MGP10 downstream; • improved correlation of grading MOE and MOR parameters in the dry mill using new analytical methods and a combination of devices. The three populations tested were stiffness-limited radiata pine, strength-limited radiata pine and Caribbean pine. Resonance tests were conducted on logs prior to sawmilling, and on boards. Raw data from existing in-line systems were captured for the green and dry boards. The dataset was analysed using classical and advanced statistical tools to provide correlations between data sets and to develop efficient strength and stiffness prediction equations. Stiffness and strength prediction algorithms were developed from raw and combined parameters. Parameters were analysed for comparison of prediction capabilities using in-line parameters, off-line parameters and a combination of in-line and off-line parameters. The results show that acoustic resonance techniques have potential for log assessment, to sort for low stiffness and/or low strength, depending on the resource. From the log measurements, a strong correlation was found between the average static MOE of the dried boards within a log and the predicted value. These results have application in segregating logs into structural and non-structural uses. Some commercial technologies are already available for this application such as Hitman LG640. For green boards it was found that in-line and laboratory acoustic devices can provide a good prediction of dry static MOE and moderate prediction for MOR.There is high potential for segregating boards at this stage of processing. Grading after the log breakdown can improve significantly the effectiveness of the mill. Subsequently, reductions in non-structural volumes can be achieved. Depending on the resource it can be expected that a 5 to 8 % reduction in non structural boards won’t be dried with an associated saving of $70 to 85/m3. For dry boards, vibration and a standard Metriguard CLT/HCLT provided a similar level of prediction on stiffness limited resource. However, Metriguard provides a better strength prediction in strength limited resources (due to this equipment’s ability to measure local characteristics). The combination of grading equipment specifically for stiffness related predictors (Metriguard or vibration) with defect detection systems (optical or X-ray scanner) provides a higher level of prediction, especially for MOR. Several commercial technologies are already available for acoustic grading on board such those from Microtec, Luxscan, Falcon engineering or Dynalyse AB for example. Differing combinations of equipment, and their strategic location within the processing chain, can dramatically improve the efficiency of the mill, the level of which will vary depending of the resource. For example, an initial acoustic sorting on green boards combined with an optical scanner associated with an acoustic system for grading dry board can result in a large reduction of the proportion of low value low non-structural produced. The application of classical MLR on several predictors proved to be effective, in particular for MOR predictions. However, the usage of a modern statistics approach(chemometrics tools) such as PLS proved to be more efficient for improving the level of prediction. Compared to existing technologies, the results of the project indicate a good improvement potential for grading in the green mill, ahead of kiln drying and subsequent cost-adding processes. The next stage is the development and refinement of systems for this purpose.