Assessment of quality defects in macadamia kernels using NIR spectroscopy

Spectral data were collected of intact and ground kernels using 3 instruments (using Si-PbS, Si, and InGaAs detectors), operating over different areas of the spectrum (between 400 and 2500 nm) and employing transmittance, interactance, and reflectance sample presentation strategies. Kernels were assessed on the basis of oil and water content, and with respect to the defect categories of insect damage, rancidity, discoloration, mould growth, germination, and decomposition. Predictive model performance statistics for oil content models were acceptable on all instruments (R2 > 0.98; RMSECV < 2.5%, which is similar to reference analysis error), although that for the instrument employing reflectance optics was inferior to models developed for the instruments employing transmission optics. The spectral positions for calibration coefficients were consistent with absorbance due to the third overtones of CH2 stretching. Calibration models for moisture content in ground samples were acceptable on all instruments (R2 > 0.97; RMSECV < 0.2%), whereas calibration models for intact kernels were relatively poor. Calibration coefficients were more highly weighted around 1360, 740 and 840 nm, consistent with absorbance due to overtones of O-H stretching and combination. Intact kernels with brown centres or rancidity could be discriminated from each other and from sound kernels using principal component analysis. Part kernels affected by insect damage, discoloration, mould growth, germination, and decomposition could be discriminated from sound kernels. However, discrimination among these defect categories was not distinct and could not be validated on an independent set. It is concluded that there is good potential for a low cost Si photodiode array instrument to be employed to identify some quality defects of intact macadamia kernels and to quantify oil and moisture content of kernels in the process laboratory and for oil content in-line. Further work is required to examine the robustness of predictive models across different populations, including growing districts, cultivars and times of harvest.

The impact of dry matter, ripeness and internal defects on consumer perceptions of avocado quality and intentions to purchase.

Insights into the relative importance of various aspects of product quality can be provided through quantitative analysis of consumer preference and choice of fruit. In this study, methods previously used to establish taste preferences for kiwifruit (Harker et al., 2008) and conjoint approaches were used to determine the influence of three key aspects of avocado quality on consumer liking and willingness to purchase fruit: dry matter percentage (DM), level of ripeness (firmness) and internal defects (bruising). One hundred and seven consumers tasted avocados with a range of DM levels from ~20% (minimally mature) to nearly 40% (very mature), and at a range of fruit firmness (ripeness) stages (firm-ripe to soft-ripe). Responses to bruising, a common quality defect in fruit obtained from the retail shelf, were examined using a conjoint approach in which consumers were presented with photographs showing fruit affected by damage of varying severity. In terms of DM, consumers showed a progressive increase in liking and intent to buy avocados as the DM increased. In terms of ripeness, liking and purchase intent was higher in avocados that had softened to a firmness of 6.5 N or below (hand-rating 5). For internal defects, conjoint analysis revealed that price, level of bruising and incidence of bruising all significantly lowered consumers' future purchase decision, but the latter two factors had a greater impact than price. These results indicate the usefulness of the methodology, and also provide realistic targets for Hass avocado quality on the retail shelf.

Impact of Stem Defect Agent Defects on Hardwood Wood Quality

Queensland's hardwood plantation industry is producing increasing volumes of sawlog, veneer and poles. Wood quality can sometimes be impaired in some plantation hardwoods when the growing trees are attacked by insect borers. Susceptibility to borer damage varies with the species as well as site conditions or location. The risk model developed from this project will enable the plantation industry to match tree species with appropriate growing conditions in Queensland.

Barley Grains Defects (Blackpoint, Pre-harvest sprouting, Kernal staining)

Screening new and existing breeding germplasm and cultivars for grain defect tolerance for breeding programs, evaluate new methods and technologies to screen more effectively for the barley grains defects - pre-harvest sprouting, blackpoint, kernel discolouration, and investigate genetic mechanisms involved in controlling barley grain defect tolerance.

National screening for barley grain defects

Three defects on barley grain can impact on the price paid to grain growers. Black point (BP), kernel staining (KS) and pre-harvest sprouting (PHS) can result in malting barley being downgraded to feed. Resistance to these defects is the best option, and in this project hundreds of breeding lines grown over three years were screened for these traits. A number of lines exhibited resistance to each defect but very few had resistance to all defects. The results from the screening program have been provided to the Australian barley breeders through the Barley Breeding Australia (BBA) program.