Application of commercially available, low-cost, miniaturised NIR spectrometers to the assessment of the sugar content of intact fruit

Recent decreases in costs, and improvements in performance, of silicon array detectors open a range of potential applications of relevance to plant physiologists, associated with spectral analysis in the visible and short-wave near infra-red (far-red) spectrum. The performance characteristics of three commercially available ‘miniature’ spectrometers based on silicon array detectors operating in the 650–1050-nm spectral region (MMS1 from Zeiss, S2000 from Ocean Optics, and FICS from Oriel, operated with a Larry detector) were compared with respect to the application of non-invasive prediction of sugar content of fruit using near infra-red spectroscopy (NIRS). The FICS–Larry gave the best wavelength resolution; however, the narrow slit and small pixel size of the charge-coupled device detector resulted in a very low sensitivity, and this instrumentation was not considered further. Wavelength resolution was poor with the MMS1 relative to the S2000 (e.g. full width at half maximum of the 912 nm Hg peak, 13 and 2 nm for the MMS1 and S2000, respectively), but the large pixel height of the array used in the MMS1 gave it sensitivity comparable to the S2000. The signal-to-signal standard error ratio of spectra was greater by an order of magnitude with the MMS1, relative to the S2000, at both near saturation and low light levels. Calibrations were developed using reflectance spectra of filter paper soaked in range of concentrations (0–20% w/v) of sucrose, using a modified partial least squares procedure. Calibrations developed with the MMS1 were superior to those developed using the S2000 (e.g. coefficient of correlation of 0.90 and 0.62, and standard error of cross-validation of 1.9 and 5.4%, respectively), indicating the importance of high signal to noise ratio over wavelength resolution to calibration accuracy. The design of a bench top assembly using the MMS1 for the non-invasive assessment of mesocarp sugar content of (intact) melon fruit is reported in terms of light source and angle between detector and light source, and optimisation of math treatment (derivative condition and smoothing function).

Influence of environmental and instrumental variables on the non-invasive prediction of Brix in pineapple using near infrared spectroscopy

The Brix content of pineapple fruit can be non-invasively predicted from the second derivative of near infrared reflectance spectra. Correlations obtained using a NIRSystems 6500 spectrophotometer through multiple linear regression and modified partial least squares analyses using a post-dispersive configuration were comparable with that from a pre-dispersive configuration in terms of accuracy (e.g. coefficient of determination, R2, 0.73; standard error of cross validation, SECV, 1.01°Brix). The effective depth of sample assessed was slightly greater using the post-dispersive technique (about 20 mm for pineapple fruit), as expected in relation to the higher incident light intensity, relative to the pre-dispersive configuration. The effect of such environmental variables as temperature, humidity and external light, and instrumental variables such as the number of scans averaged to form a spectrum, were considered with respect to the accuracy and precision of the measurement of absorbance at 876 nm, as a key term in the calibration for Brix, and predicted Brix. The application of post-dispersive near infrared technology to in-line assessment of intact fruit in a packing shed environment is discussed.

Non-invasive assessment of pineapple and mango fruit quality using near infra-red spectroscopy

The potential of near infra-red (NIR) spectroscopy for non-invasive measurement of fruit quality of pineapple (Ananas comosus var. Smooth Cayenne) and mango (Magnifera indica var. Kensington) fruit was assessed. A remote reflectance fibre optic probe, placed in contact with the fruit skin surface in a light-proof box, was used to deliver monochromatic light to the fruit, and to collect NIR reflectance spectra (760–2500 nm). The probe illuminated and collected reflected radiation from an area of about 16 cm2. The NIR spectral attributes were correlated with pineapple juice Brix and with mango flesh dry matter (DM) measured from fruit flesh directly underlying the scanned area. The highest correlations for both fruit were found using the second derivative of the spectra (d2 log 1/R) and an additive calibration equation. Multiple linear regression (MLR) on pineapple fruit spectra (n = 85) gave a calibration equation using d2 log 1/R at wavelengths of 866, 760, 1232 and 832 nm with a multiple coefficient of determination (R2) of 0.75, and a standard error of calibration (SEC) of 1.21 °Brix. Modified partial least squares (MPLS) regression analysis yielded a calibration equation with R2 = 0.91, SEC = 0.69, and a standard error of cross validation (SECV) of 1.09 oBrix. For mango, MLR gave a calibration equation using d2 log 1/R at 904, 872, 1660 and 1516 nm with R2 = 0.90, and SEC = 0.85% DM and a bias of 0.39. Using MPLS analysis, a calibration equation with R2 = 0.98, SEC = 0.54 and SECV = 1.19 was obtained. We conclude that NIR technology offers the potential to assess fruit sweetness in intact whole pineapple and DM in mango fruit, respectively, to within 1° Brix and 1% DM, and could be used for the grading of fruit in fruit packing sheds.

A towed instrument package for fisheries research in great barrier reef waters

A tethered remote instrument package (TRIP) has been developed for biological surveys over Queensland's continental shelf and slope. The present system, evolved from an earlier sled configuration, is suspended above the sea bed and towed at low speeds. Survey information is collected through video and film cameras while instrument and environmental variables are handled by a minicomputer. The operator was able to "fly" the instrument package above the substrate by using an altitude echosounder, forward-looking sonar and real-time television viewing. Unwanted movements of the viewing system were stabilized through a gyro-controlled camera-head panning system. the hydrodynamic drag of the umbilical presented a major control problem which could be overcome only by a reduction in towing speed. Despite the constraints of towing a device such as this through the coral reef environment, the package performed well during a recent biological survey where it was worked at 50% of its 350 m design depth.

Influence of Measured Characteristics on Price Received for Merino Wool from the Traprock Area of Southern Queensland

In this study of a commercial wool clip sold in the years 1991/92-1996/97, the effect of wool characteristics, (staple length, staple strength, fibre diameter, position of break, vegetable matter, hauteur, yield and coefficient of variation of staple length) on price was explored together with their effect on the ratio of price received per lot to the average weekly price (1994/95 basis) for clean wool of the same fibre diameter. Fibre diameter and where the point of break occurred had the most effect on price. As hauteur, staple length and yield increased, so did the price ratio but it decreased as the percentage of vegetable matter and the coefficient of variation of the staple length increased. The ratio of proceeds if all wool had been sold at average weekly market price, to proceeds if all wool had been 21µm or less, indicated little financial advantage over the six-year period as most sale lots were under 22µm. To raise the proceeds of sale above the proceeds estimated using average market price for each lot, the analyses suggested that hauteur, staple length and its coefficient of variation, could be considered, in addition to fibre diameter, when sourcing wethers for purchase. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Near infrared reflectance as a rapid and inexpensive surrogate measure for fatty acid composition and oil content in peanuts (Arachis hypogaea L.)

The fatty acid composition of ground nuts (Arachis hypogaea L.) commonly known as peanuts, is an important consideration when a new variety is being released. The composition impacts on nutrition and, importantly, self-life of peanut products. To select for suitable breeding material, it was necessary to develop a rapid, non-derstructive and cost-efficient method. Near infrared spectroscopy was chosen as that methodology. Calibrations were developed for two major fatty-acid components, oleic and linoleic acids and two minor components, palmitic and stearic acids, as well as total oil content. Partial least squares models indicated a high level of precision with a squared multiple correlation coefficient of greater than 0.90 for each constitutent. Standard errors for prediction for oleic, linoleic, palmitic, stearic acids and total oil content were 6.4%, 4.5%, 0.8%, 0.9% and 1.3% respectively. The results demonstrated that reasonable calibrations could be developed to predict oil composition and content of peanuts for a breeding programme.

Runoff, sediment loss and water quality from forest roads in a southeast Queensland coastal plain Pinus plantation

Runoff and sediment loss from forest roads were monitored for a two-year period in a Pinus plantation in southeast Queensland. Two classes of road were investigated: a gravelled road, which is used as a primary daily haulage route for the logging area, and an ungravelled road, which provides the main access route for individual logging compartments and is intensively used as a haulage route only during the harvest of these areas (approximately every 30 years). Both roads were subjected to routine traffic loads and maintenance during the study. Surface runoff in response to natural rainfall was measured and samples taken for the determination of sediment and nutrient (total nitrogen, total phosphorus, dissolved organic carbon and total iron) loads from each road. Results revealed that the mean runoff coefficient (runoff depth/rainfall depth) was consistently higher from the gravelled road plot with 0.57, as compared to the ungravelled road with 0.38. Total sediment loss over the two-year period was greatest from the gravelled road plot at 5.7 t km−1 compared to the ungravelled road plot with 3.9 t km−1. Suspended solids contributed 86% of the total sediment loss from the gravelled road, and 72% from the ungravelled road over the two years. Nitrogen loads from the two roads were both relatively constant throughout the study, and averaged 5.2 and 2.9 kg km−1 from the gravelled and ungravelled road, respectively. Mean annual phosphorus loads were 0.6 kg km−1 from the gravelled road and 0.2 kg km−1 from the ungravelled road. Organic carbon and total iron loads increased in the second year of the study, which was a much wetter year, and are thought to reflect the breakdown of organic matter in roadside drains and increased sediment generation, respectively. When road and drain maintenance (grading) was performed runoff and sediment loss were increased from both road types. Additionally, the breakdown of the gravel road base due to high traffic intensity during wet conditions resulted in the formation of deep (10 cm) ruts which increased erosion. The Water Erosion Prediction Project (WEPP):Road model was used to compare predicted to observed runoff and sediment loss from the two road classes investigated. For individual rainfall events, WEPP:Road predicted output showed strong agreement with observed values of runoff and sediment loss. WEPP:Road predictions for annual sediment loss from the entire forestry road network in the study area also showed reasonable agreement with the extrapolated observed values.

Using immunology and resistant sheep to beat the fly

New methods for controlling blowfly strike will be needed when mulesing is phased out and the availability or efficacy of insecticides for control of fly strike decreases. The Australian Sheep Industry CRC has pursued two approaches for the development of new methods to help control blowfly strike. In the first, genetic resistance of sheep to survival and growth of blowfly larvae was examined. Resistance to growth of larvae was heritable (0.29 ± 0.22). The trait was not associated with resistance to internal parasites, nor was it influenced by wool characteristics such as fibre diameter or coefficient of variation of fibre diameter. This new trait differs from resistance to fly strike associated with resistance to fleece rot. Because measurement of the trait is labour intensive, gene markers or correlated measures are needed before it will be suitable for industry adoption. The second approach examined the impact of larval products on the immmune system of the sheep. Larvae suppress the sheep immune system and thereby limit the ability of the sheep to reject the larvae. The immunosuppresive agent is being purified and strategies to abolish its activity are being explored. Abolition of immunosuppression would create opportunities for the development of new vaccines againts blowfly strike.

Process studies of odour emissions from effluent ponds using machine-based odour measurement

Replicable experimental studies using a novel experimental facility and a machine-based odour quantification technique were conducted to demonstrate the relationship between odour emission rates and pond loading rates. The odour quantification technique consisted of an electronic nose, AromaScan A32S, and an artificial neural network. Odour concentrations determined by olfactometry were used along with the AromaScan responses to train the artificial neural network. The trained network was able to predict the odour emission rates for the test data with a correlation coefficient of 0.98. Time averaged odour emission rates predicted by the machine-based odour quantification technique, were strongly correlated with volatile solids loading rate, demonstrating the increased magnitude of emissions from a heavily loaded effluent pond. However, it was not possible to obtain the same relationship between volatile solids loading rates and odour emission rates from the individual data. It is concluded that taking a limited number of odour samples over a short period is unlikely to provide a representative rate of odour emissions from an effluent pond. A continuous odour monitoring instrument will be required for that more demanding task.

Dietary composition manipulation to enhance the performance of juvenile barramundi (Lates calcarifer Bloch) reared in cool water

Barramundi Lates calcarifer reared in cool water (20-22 degrees C) grow slowly and feed is used poorly compared with fish in warm water (28-32 degrees C). Two comparative slaughter growth assays were carried out with juvenile barramundi to see if increasing the digestible energy (DE) and/or the n-3 highly unsaturated fatty acid (n-3 HUFA) content of the feed would improve growth of fish raised in cool water. Increasing the DE content of the feed from 15 to 17 or 19 MJ kg(-1) while maintaining a constant protein to energy ratio in Experiment 1 brought about significant improvements in feed conversion ratio (FCR) (from 2.01 to 1.19) and daily growth coefficient (DGC; from 0.69 to 1.08%/day) for fish at 20 degrees C. For fish at 29 degrees C, improvements, while significant, were of a lesser magnitude: from 1.32 to 0.97 for FCR and from 3.24 to 3.65%/day for DGC. Increasing the absolute amount of dietary n-3 HUFA, expressed as the sum of eicosapentaenoic and docosahexaenoic fatty acids, from 0.5% to 2.0% in Experiment 2 improved DGC linearly and FCR curvilinearly for fish at 29 degrees C whereas at 20 degrees C, DGC was not affected while FCR improved slightly (from 1.83 to 1.68). Feed conversion ratio was optimized with a dietary n-3 HUFA of about 1.5%. Providing barramundi with a feed that is high in DE (viz 19 MJ kg(-1)) and a digestible protein to DE ratio of 22.5 g MJ(-1) is a practical strategy for improving the productivity of barramundi cultured in cool water whereas increasing dietary n-3 HUFA conferred very little additional benefit.

A comparison of mark-recapture distance-sampling methods applied to aerial surveys of eastern grey kangaroos

Aerial surveys of kangaroos (Macropus spp.) in Queensland are used to make economically important judgements on the levels of viable commercial harvest. Previous analysis methods for aerial kangaroo surveys have used both mark-recapture methodologies and conventional distance-sampling analyses. Conventional distance sampling has the disadvantage that detection is assumed to be perfect on the transect line, while mark-recapture methods are notoriously sensitive to problems with unmodelled heterogeneity in capture probabilities. We introduce three methodologies for combining together mark-recapture and distance-sampling data, aimed at exploiting the strengths of both methodologies and overcoming the weaknesses. Of these methods, two are based on the assumption of full independence between observers in the mark-recapture component, and this appears to introduce more bias in density estimation than it resolves through allowing uncertain trackline detection. Both of these methods give lower density estimates than conventional distance sampling, indicating a clear failure of the independence assumption. The third method, termed point independence, appears to perform very well, giving credible density estimates and good properties in terms of goodness-of-fit and percentage coefficient of variation. Estimated densities of eastern grey kangaroos range from 21 to 36 individuals km-2, with estimated coefficients of variation between 11% and 14% and estimated trackline detection probabilities primarily between 0.7 and 0.9.

Quantitative assessment of total phenol contents of European oak (Quercus petraea and Quercus robur) by diffuse reflectance NIR spectroscopy on solid wood surfaces

Near infrared spectroscopy (NIRS) combined with multivariate analysis techniques was applied to assess phenol content of European oak. NIRS data were firstly collected directly from solid heartwood surfaces: in doing so, the spectra were recorded separately from the longitudinal radial and the transverse section surfaces by diffuse reflectance. The spectral data were then pretreated by several pre-processing procedures, such as multiplicative scatter correction, first derivative, second derivative and standard normal variate. The tannin contents of sawmill collected from the longitudinal radial and transverse section surfaces were determined by quantitative extraction with water/methanol (1:4, by vol). Then, total phenol contents in tannin extracts were measured by the Folin-Ciocalteu method. The NIR data were correlated against the Folin-Ciocalteu results. Calibration models built with partial least squares regression displayed strong correlation - as expressed by high determination correlation coefficient (r2) and high ratio of performance to deviation (RPD) - between measured and predicted total phenols content, and weak calibration and prediction errors (RMSEC, RMSEP). The best calibration was provided with second derivative spectra (r2 value of 0.93 for the longitudinal radial plane and of 0.91 for the transverse section plane). This study illustrates that the NIRS technique when used in conjunction with multivariate analysis could provide reliable, quick and non-destructive assessment of European oak heartwood extractives.

Use of part records in Merino breeding programs - The inheritance of wool growth and fibre traits during different times of the year to determine their value in Merino breeding programs

Fibre diameter can vary dramatically along a wool staple, especially in the Mediterranean environment of southern Australia with its dry summers and abundance of green feed in spring. Other research results have shown a very low phenotypic correlation between fibre diameter grown between seasons. Many breeders use short staples to measure fibre diameter for breeding purposes and also to promote animals for sale. The effectiveness of this practice is determined by the relative response to selection by measuring fibre traits on a full 12 months wool staple as compared to measuring them only on part of a staple. If a high genetic correlation exists between the part record and the full record, then using part records may be acceptable to identify genetically superior animals. No information is available on the effectiveness of part records. This paper investigated whether wool growth and fibre diameter traits of Merino wool grown at different times of the year in a Mediterranean environment, are genetically the same trait, respectively. The work was carried out on about 7 dyebanded wool sections/animal.year, on ewes from weaning to hogget age, in the Katanning Merino resource flocks over 6 years. Relative clean wool growth of the different sections had very low heritability estimates of less than 0.10, and they were phenotypically and genetically poorly correlated with 6 or 12 months wool growth. This indicates that part record measurement of clean wool growth of these sections will be ineffective as indirect selection criteria to improve wool growth genetically. Staple length growth as measured by the length between dyebands, would be more effective with heritability estimates of between 0.20 and 0.30. However, these measurements were shown to have a low genetic correlation with wool grown for 12 months which implies that these staple length measurements would only be half as efficient as the wool weight for 6 or 12 months to improve total clean wool weight. Heritability estimates of fibre diameter, coefficient of variation of fibre diameter and fibre curvature were relatively high and were genetically and phenotypically highly correlated across sections. High positive phenotypic and genetic correlations were also found between fibre diameter, coefficient of variation of fibre diameter and fibre curvature of the different sections and similar measurements for wool grown over 6 or 12 months. Coefficient of variation of fibre diameter of the sections also had a moderate negative phenotypic and genetic correlation with staple strength of wool staples grown over 6 months indicating that coefficient of variation of fibre diameter of any section would be as good an indirect selection criterion to improve stable strength as coefficient of variation of fibre diameter for wool grown over 6 or 12 months. The results indicate that fibre diameter, coefficient of variation of fibre diameter and fibre curvature of wool grown over short periods of time have virtually the same heritability as that of wool grown over 12 months, and that the genetic correlation between fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part and on full records is very high (rg > 0.85). This indicates that fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part records can be used as selection criteria to improve these traits. However, part records of greasy and clean wool growth would be much less efficient than fleece weight for wool grown over 6 or 12 months because of the low heritability of part records and the low genetic correlation between these traits on part records and on wool grown for 12 months.

Simulating the effects of saline and sodic subsoils on wheat crops growing on Vertosols

Soils with high levels of chloride and/or sodium in their subsurface layers are often referred to as having subsoil constraints (SSCs). There is growing evidence that SSCs affect wheat yields by increasing the lower limit of a crop's available soil water (CLL) and thus reducing the soil's plant-available water capacity (PAWC). This proposal was tested by simulation of 33 farmers' paddocks in south-western Queensland and north-western New South Wales. The simulated results accounted for 79% of observed variation in grain yield, with a root mean squared deviation (RMSD) of 0.50 t/ha. This result was as close as any achieved from sites without SSCs, thus providing strong support for the proposed mechanism that SSCs affect wheat yields by increasing the CLL and thus reducing the soil's PAWC. In order to reduce the need to measure CLL of every paddock or management zone, two additional approaches to simulating the effects of SSCs were tested. In the first approach the CLL of soils was predicted from the 0.3-0.5 m soil layer, which was taken as the reference CLL of a soil regardless of its level of SSCs, while the CLL values of soil layers below 0.5 m depth were calculated as a function of these soils' 0.3-0.5 m CLL values as well as of soil depth plus one of the SSC indices EC, Cl, ESP, or Na. The best estimates of subsoil CLL values were obtained when the effects of SSCs were described by an ESP-dependent function. In the second approach, depth-dependent CLL values were also derived from the CLL values of the 0.3-0.5 m soil layer. However, instead of using SSC indices to further modify CLL, the default values of the water-extraction coefficient (kl) of each depth layer were modified as a function of the SSC indices. The strength of this approach was evaluated on the basis of correlation of observed and simulated grain yields. In this approach the best estimates were obtained when the default kl values were multiplied by a Cl-determined function. The kl approach was also evaluated with respect to simulated soil moisture at anthesis and at grain maturity. Results using this approach were highly correlated with soil moisture results obtained from simulations based on the measured CLL values. This research provides strong evidence that the effects of SSCs on wheat yields are accounted for by the effects of these constraints on wheat CLL values. The study also produced two satisfactory methods for simulating the effects of SSCs on CLL and on grain yield. While Cl and ESP proved to be effective indices of SSCs, EC was not effective due to the confounding effect of the presence of gypsum in some of these soils. This study provides the tools necessary for investigating the effects of SSCs on wheat crop yields and natural resource management (NRM) issues such as runoff, recharge, and nutrient loss through simulation studies. It also facilitates investigation of suggested agronomic adaptations to SSCs.

Atrazine degradation and transport in runoff on a Black Vertosol

In Australia communities are concerned about atrazine being detected in drinking water supplies. It is important to understand mechanisms by which atrazine is transported from paddocks to waterways if we are to reduce movement of agricultural chemicals from the site of application. Two paddocks cropped with grain sorghum on a Black Vertosol were monitored for atrazine, potassium chloride (KCl) extractable atrazine, desethylatrazine (DEA), and desisopropylatrazine (DIA) at 4 soil depths (0-0.05, 0.05-0.10, 0.10-0.20, and 0.20-0.30 m) and in runoff water and runoff sediment. Atrazine + DEA + DIA (total atrazine) had a half-life in soil of 16-20 days, more rapid dissipation than in many earlier reports. Atrazine extracted in dilute potassium chloride, considered available for weed control, was initially 34% of the total and had a half-life of 15-20 days until day 30, after which it dissipated rapidly with a half life of 6 days. We conclude that, in this region, atrazine may not pose a risk for groundwater contamination, as only 0.5% of applied atrazine moved deeper than 0.20 m into the soil, where it dissipated rapidly. In runoff (including suspended sediment) atrazine concentrations were greatest during the first runoff event (57 days after application) (85 μg/L) and declined with time. After 160 days, the total atrazine lost in runoff was 0.4% of the initial application. The total atrazine concentration in runoff was strongly related to the total concentration in soil, as expected. Even after 98% of the KCl-extractable atrazine had dissipated (and no longer provided weed control), runoff concentrations still exceeded the human health guideline value of 40 μg/L. For total atrazine in soil (0-0.05 m), the range for coefficient of soil sorption (Kd) was 1.9-28.4 mL/g and for soil organic carbon sorption (KOC) was 100-2184 mL/g, increasing with time of contact with the soil and rapid dissipation of the more soluble, available phase. Partition coefficients in runoff for total atrazine were initially 3, increasing to 32 and 51 with time, values for DEA being half these. To minimise atrazine losses, cultural practices that maximise rain infiltration, and thereby minimise runoff, and minimise concentrations in the soil surface should be adopted.