Assessment of quality defects in macadamia kernels using NIR spectroscopy

Spectral data were collected of intact and ground kernels using 3 instruments (using Si-PbS, Si, and InGaAs detectors), operating over different areas of the spectrum (between 400 and 2500 nm) and employing transmittance, interactance, and reflectance sample presentation strategies. Kernels were assessed on the basis of oil and water content, and with respect to the defect categories of insect damage, rancidity, discoloration, mould growth, germination, and decomposition. Predictive model performance statistics for oil content models were acceptable on all instruments (R2 > 0.98; RMSECV < 2.5%, which is similar to reference analysis error), although that for the instrument employing reflectance optics was inferior to models developed for the instruments employing transmission optics. The spectral positions for calibration coefficients were consistent with absorbance due to the third overtones of CH2 stretching. Calibration models for moisture content in ground samples were acceptable on all instruments (R2 > 0.97; RMSECV < 0.2%), whereas calibration models for intact kernels were relatively poor. Calibration coefficients were more highly weighted around 1360, 740 and 840 nm, consistent with absorbance due to overtones of O-H stretching and combination. Intact kernels with brown centres or rancidity could be discriminated from each other and from sound kernels using principal component analysis. Part kernels affected by insect damage, discoloration, mould growth, germination, and decomposition could be discriminated from sound kernels. However, discrimination among these defect categories was not distinct and could not be validated on an independent set. It is concluded that there is good potential for a low cost Si photodiode array instrument to be employed to identify some quality defects of intact macadamia kernels and to quantify oil and moisture content of kernels in the process laboratory and for oil content in-line. Further work is required to examine the robustness of predictive models across different populations, including growing districts, cultivars and times of harvest.

The impact of dry matter, ripeness and internal defects on consumer perceptions of avocado quality and intentions to purchase.

Insights into the relative importance of various aspects of product quality can be provided through quantitative analysis of consumer preference and choice of fruit. In this study, methods previously used to establish taste preferences for kiwifruit (Harker et al., 2008) and conjoint approaches were used to determine the influence of three key aspects of avocado quality on consumer liking and willingness to purchase fruit: dry matter percentage (DM), level of ripeness (firmness) and internal defects (bruising). One hundred and seven consumers tasted avocados with a range of DM levels from ~20% (minimally mature) to nearly 40% (very mature), and at a range of fruit firmness (ripeness) stages (firm-ripe to soft-ripe). Responses to bruising, a common quality defect in fruit obtained from the retail shelf, were examined using a conjoint approach in which consumers were presented with photographs showing fruit affected by damage of varying severity. In terms of DM, consumers showed a progressive increase in liking and intent to buy avocados as the DM increased. In terms of ripeness, liking and purchase intent was higher in avocados that had softened to a firmness of 6.5 N or below (hand-rating 5). For internal defects, conjoint analysis revealed that price, level of bruising and incidence of bruising all significantly lowered consumers' future purchase decision, but the latter two factors had a greater impact than price. These results indicate the usefulness of the methodology, and also provide realistic targets for Hass avocado quality on the retail shelf.

Predicting the cost of eradication for 41 Class 1 declared weeds in Queensland

The feasibility of state-wide eradication of 41 invasive plant taxa currently listed as ‘Class 1 declared pests’ under the Queensland Land Protection (Pest and Stock Route Management) Act 2002 was assessed using the predictive model ‘WeedSearch’. Results indicated that all but one species (Alternanthera philoxeroides) could be eradicated, provided sufficient funding and labour were available. Slightly less than one quarter (24.4%) (n = 10) of Class 1 weed taxa could be eradicated for less than $100 000 per taxon. An additional 43.9% (n = 18) could be eradicated for between $100 000 and $1M per taxon. Hence, 68.3% of Class 1 weed taxa (n = 28) could be eradicated for less than $1M per taxon. Eradication of 29.3% (n = 12) is predicted to cost more than $1M per taxon. Comparison of these WeedSearch outputs with either empirical analysis or results from a previous application of the model suggests that these costs may, in fact, be underestimates. Considering the likelihood that each weed will cost the state many millions of dollars in long-term losses (e.g. losses to primary production, environmental impacts and control costs), eradication seems a wise investment. Even where predicted costs are over $1M, eradication can still offer highly favourable benefit:cost ratios. The total (cumulative) cost of eradication of all 41 weed taxa is substantial; for all taxa, the estimated cost of eradication in the first year alone is $8 618 000. This study provides important information for policy makers, who must decide where to invest public funding.

Background to the approved beneficial Cynodon spp. vegetative cultivars within Australia

The growth of the Australian turfgrass industry has significantly expanded over recent decades. One reason for this occurring has been with development of better suited or higher quality turfgrass cultivars for Australia’s harsh climatic conditions. In recent years drought has widely affected the turfgrass industry and as such, greater drought tolerant C4 grasses such as Cynodon spp. have been used. In 2008, as part of the 24th Australian Turfgrass Conference Proceedings, Peter McMaugh wrote an extensive article on the couch grass breeding history in Australia. This paper contains an extension to his work detailing the current (1950s to 2010) Cynodon species found in Australia. Detailed information has been sourced in relation to the origin and development of the grasses which are suitable for turfgrass use. Such detail provides an interesting picture of the source of proliferation of newer cultivars and how the Australian industry has evolved with the introduction of overseas and Australian selected cultivars. The information adds to the preceding work, including morphological and agronomic attributes and how closely each selection or cultivar is related. The cultivars discussed in this article (listed alphabetically) are derived from one of the four classifications identified by the breeder/author, being (i) Cynodon sp. (although the cultivar contained within the taxa fits best being classified as a Cynodon hybrid), (ii) Cynodon dactylon x C. transvaalensis (Cynodon hybrid), (iii) Cynodon dactylon (green couch) and (iv) Cynodon dactylon x C. magenissii.

Leading Sheep III

Leading Sheep is a framework for supporting decision-making about technologies and practices to increase the profitability and productivity of the Queensland Sheep Businesses. Leading Sheep aims to achieve a high level of engagement with sheep businesses in Queensland to support their ongoing decision making processes about productivity and profitability.

Impact of Stem Defect Agent Defects on Hardwood Wood Quality

Queensland's hardwood plantation industry is producing increasing volumes of sawlog, veneer and poles. Wood quality can sometimes be impaired in some plantation hardwoods when the growing trees are attacked by insect borers. Susceptibility to borer damage varies with the species as well as site conditions or location. The risk model developed from this project will enable the plantation industry to match tree species with appropriate growing conditions in Queensland.

Barley Grains Defects (Blackpoint, Pre-harvest sprouting, Kernal staining)

Screening new and existing breeding germplasm and cultivars for grain defect tolerance for breeding programs, evaluate new methods and technologies to screen more effectively for the barley grains defects - pre-harvest sprouting, blackpoint, kernel discolouration, and investigate genetic mechanisms involved in controlling barley grain defect tolerance.

Risk assessment and preventive strategies for herbicide resistance in NR (phase III)

The threat and management of glyphosate# resistant weeds are major issues facing northern region growers. At present five weeds are confirmed glyphosate-resistant: barnyard grass, liverseed grass, windmill grass, annual ryegrass and flaxleaf fleabane. This project used 25 experiments to investigate the ecology of the grass weeds, plus new or improved chemical and non-chemical control tactics for them. The refined glyphosate resistance model developed in this project used the experiments' findings to predict the long-term impacts on evolution of resistance and on seed bank numbers of resistant weeds. These data led to revised management and resistance avoidance strategies, which were published in the Reporter newsletter, and via an on-line risk assessment tool. - See more at: http://finalreports.grdc.com.au/UQ00054#sthash.oTkCN4Sk.dpuf

Herbicide tolerance of barley and wheat cultivars in NR (phase III)

During the past 10 years, this project tested 23 barley and 51 wheat varieties with 19 and 34 registered herbicides, respectively. It concentrated on new varieties and herbicides. The research highlighted that Northern Region (NR) wheat and barley varieties differed considerably in their sensitivity to these herbicides. Overall, 9 per cent of wheat variety x herbicide combinations and 6 per cent of barley variety x herbicide combinations had significant yield losses (3 to 38%) from herbicides at recommended rates and crop stages. In addition, 21 to 23 per cent had significant yield losses from herbicides at double rates, indicating a narrow margin of crop safety.

National screening for barley grain defects

Three defects on barley grain can impact on the price paid to grain growers. Black point (BP), kernel staining (KS) and pre-harvest sprouting (PHS) can result in malting barley being downgraded to feed. Resistance to these defects is the best option, and in this project hundreds of breeding lines grown over three years were screened for these traits. A number of lines exhibited resistance to each defect but very few had resistance to all defects. The results from the screening program have been provided to the Australian barley breeders through the Barley Breeding Australia (BBA) program.

Construction timbers in Queensland. Book 1 and Book 2: Properties and specifications for satisfactory performance of construction timbers in Queensland. Class 1 and Class 10 buildings (houses, carports, garages, greenhouses and sheds). 2013 edition.

This publication lists the more important wood properties of commercial timbers used for construction in Queensland. It also provides requirements and conditions of use for these timbers to provide appropriate design service life in various construction applications. The correct specification of timber considers a range of timber properties including, but not limited to, stress grade; durability class; moisture content and insect resistance. For the specification of timber sizes and spans, relevant Australian Standards and design manuals should be consulted—e.g. Australian Standard AS 1684 series Residential timber—framed construction parts 2 and 3 (Standards Australia 2006a;b.) Book 1 explains the terms used; with reference to nomenclature; origin and timber properties presented under specific column headings in the schedules (Book 2). It also explains target design life; applications and decay hazard zones; presented in the Book 2 Schedules. Book 2 consists of reference tables; presented as schedules A; B and C: • Schedule A contains commercial mixtures of unidentified timbers and of some Australian and imported softwoods. Index numbers 1–10 • Schedule B contains Australian-grown timber species; including both natural forests and plantations. Index numbers 11–493 • Schedule C contains timbers imported into Australia from overseas. Index numbers 494–606 Each schedule has two parts presenting data in tables. • Part 1: Nomenclature, origin and properties of imported timber species • Part 2: Approved uses for commercial mixtures of imported timber species The recommendations made in this publication assume that good building practice will be carried out.