Field assessment of the resistance of timber products to termite (Isoptera) damage: Results can change with the amount of bait wood

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

Pitfalls and benefits of involving industry in fisheries research: A case study of the live reef fish industry in Queensland, Australia

Including collaboration with industry members as an integral part of research activities is a relatively new approach to fisheries research. Earlier approaches to involving fishers in research usually involved compulsory accommodations of research, such as through compulsory observer programs, in which fishers were seen as subjects of rather than participants in research. This new approach brings with it significant potential benefits but also some unique issues both for the researchers and the participating industry members. In this paper we describe a research project involving the Queensland Coral Reef Finfish Fishery that originated from industry and community concerns about changes in marketing practices in an established commercial line fishery. A key aspect of this project was industry collaboration in all stages of the research, from formulation of objectives to assistance with interpretation of results. We discuss this research as a case study of some of the issues raised by collaboration between industry and research groups in fisheries research and the potential pitfalls and benefits of such collaborations for all parties. A dedicated liaison and extension strategy was a key element in the project to develop and maintain the relationships between fishers and researchers that were fundamental to the success of the collaboration. A major research benefit of the approach was the provision of information not available from other sources: 300 days of direct and unimpeded observation of commercial fishing by researchers; detailed catch and effort records from a further 126 fishing trips; and 53 interviews completed with fishers. Fishers also provided extensive operational information about the fishery as well as ongoing support for subsequent research projects. The time and resources required to complete the research in this consultative framework were greater than for more traditional, researcher-centric fisheries research, but the benefits gained far outweighed the costs.

Management Guidelines for New Warm-Season Grasses in Australia

After more than 30 years in which ‘Tifgreen’ and ‘Tifdwarf’ were the only greens-quality varieties available, the choice for golf courses and bowls clubs in northern Australia has been expanded to include six new Cynodon hybrids [Cynodon dactylon (L.) Pers x Cynodon transvaalensis Burtt-Davy]. Five of these – ‘Champion Dwarf’ (Texas), ‘MS-Supreme’ (Mississippi), FloraDwarf™ (Florida), ‘TifEagle’ (Georgia), MiniVerde™ (Arizona) - are from US breeding programs, while the sixth, ‘TL2’ (marketed as Novotek™) was selected in north Queensland. The finer, denser and lower growing habit of the “ultradwarf” cultivars allows very low mowing heights (e.g. 2.5 mm) to be imposed, resulting in denser and smoother putting and bowls surfaces. In addition to the Cynodon hybrids, four new greens quality seashore paspalum (Paspalum vaginatum O. Swartz) cultivars including ‘Sea Isle 2000’, Sea Isle Supreme™, Velvetene™ and Sea Dwarf™ (where tolerance of salty water is required) expands the range of choices for greens in difficult environments. The project was developed to determine (a) the appropriate choice of cultivar for different environments and budgets, and (b) best management practices for the new cultivars which differ from the Cynodon hybrid industry standards ‘Tifgreen’ and ‘Tifdwarf’. Management practices, particularly fertilising, mowing heights and frequency, and thatch control were investigated to determine optimum management inputs and provide high quality playing surfaces with the new grasses. To enable effective trialling of these new and old cultivars it was essential to have a number of regional sites participating in the study. Drought and financial hardship of many clubs presented an initial setback with numerous clubs wanting to be involved in the study but were unable to commit due to their financial position at the time. The study was fortunate to have seven regional sites from Queensland, New South Wales, Victoria and South Australia volunteer to be involved in the study which would add to the results being collected at the centralised test facility being constructed at DEEDI’s Redlands Research Station. The major research findings acquired from the eight trial sites included: • All of the new second generation “ultradwarf” couchgrasses tend to produce a large amount of thatch with MiniVerde™ being the greatest thatch producer, particularly compared to ‘Tifdwarf’ and ‘Tifgreen’. The maintenance of the new Cynodon hybrids will require a program of regular dethatching/grooming as well as regular light dustings of sand. Thatch prevention should begin 3 to 4 weeks after planting a new “ultradwarf” couchgrass green, with an emphasis on prevention rather than control. • The “ultradwarfs” produced faster green speeds than the current industry standards ‘Tifgreen’ and ‘Tifdwarf’. However, all Cynodon hybrids were considerably faster than the seashore paspalums (e.g. comparable to the speed diference of Bentgrass and couchgrass) under trial conditions. Green speed was fastest being cut at 3.5 mm and rolled (compared to 3.5 mm cut, no roll and 2.7 mm cut, no roll). • All trial sites reported the occurrence of disease in the Cynodon hybrids with the main incidence of disease occurring during the dormancy period (autumn and winter). The main disease issue reported was “patch diseases” which includes both Gaumannomyces and Rhizoctonia species. There was differences in the severity of the disease between cultivars, however, the severity of the disease was not consistent between cultivars and is largely attributed to an environment (location) effect. In terms of managing the occurrence of disease, the incidence of disease is less severe where there is a higher fertility rate (about 3 kgN/100m2/year) or a preventitatve fungicide program is adopted. • Cynodon hybrid and seashore paspalum cultivars maintained an acceptable to ideal surface being cut between 2.7 mm and 5.0 mm. “Ultradwarf” cultivars can tolerate mowing heights as low as 2.5 mm for short periods but places the plant under high levels of stress. Greens being maintained at a continually lower cutting height (e.g. 2.7 mm) of both species is achievable, but would need to be cut daily for best results. Seashore paspalums performed best when cut at a height of between 2.7 mm and 3.0 mm. If a lower cutting height is adopted, regular and repeated mowings are required to reduce scalping and produce a smooth surface. • At this point in time the optimum rate of nitrogen (N) for the Cynodon hybrids is 3 kg/100m2/year and while the seashore paspalums is 2 to 3 kg/100m2/year. • Dormancy occurred for all Cynodon and seashore paspalum culitvars from north in Brisbane (QLD) to south in Mornington Peninsula (VIC) and west to Novar Gardens (SA). Cynodon and Paspalum growth in both Victoria and South Australia was less favourable as a result of the cooler climates. • After combining the data collected from all eight sites, the results indicated that there can be variation (e.g. turfgrass quality, colour, disease resistance, performace) depending on the site and climatic conditions. Such evidence highlights the need to undertake genotype by environment (G x E) studies on new and old cultivars prior to conversion or establishment. • For a club looking to select either a Cynodon hybrid or seashore paspalum cultivar for use at their club they need to: - Review the research data. - Look at trial plots. - Inspect greens in play that have the new grasses. - Select 2 to 3 cultivars that are considered to be the better types. - Establish them in large (large enough to putt on) plots/nursery/practice putter. Ideally the area should be subjected to wear. - Maintain them exactly as they would be on the golf course/lawn bowls green. This is a critical aspect. Regular mowing, fertilising etc. is essential. - Assess them over at least 2 to 3 years. - Make a selection and establish it in a playing green so that it is subjected to typical wear.

Passionfruit growing guide - Second edition

This edition of 'The passionfruit growing guide' is a substantial update of the first edition, which was published in 2006. Each chapter deals with a specific aspect of the development and management of a passionfruit plantation. This guide is intended for use by prospective, new and established growers and addresses all aspects of passionfruit growing, from site selection and planning through to harvesting and marketing the fruit. It provides practical advice and propogation, fertilising, irrigation, and pest disease and control. Also, it includes information on varieties of passionfruit, financial budgets, chemicals registered for use on passionfruit and useful contacts.

Improved understanding of the damage, ecology, and management of mirids and stinkbugs in Bollgard II

In recent years mirids and stinkbugs have emerged as important sucking pests in cotton. While stinkbugs are causing damage to bolls, mirids are causing damage to seedlings, squares and bolls. With the increasing adoption of Bollgard II and IPM approaches the use of broad-spectrum chemicals to kill Helicoverpa has been reduced and as a result mirids and stinkbugs are building to levels causing damage to bolls later in crop growth stages. Studies on stinkbugs by Dr Moazzem Khan revealed that green vegetable bug (GVB) caused significant boll damage and yield loss. A preliminary study by Dr Khan on mirids revealed that high mirid numbers at later growth stages also caused significant boll damage and that damage caused by mirids and GVB were similar. Mirids and stinkbugs therefore demand greater attention in order to minimise losses caused by these pests and to develop IPM strategies against these pests to enhance gains in IPM that have been made with Bt-transgenic cotton. Progress in this area of research will maintain sustainability and profitability of the Australian cotton industry. Mirid damage at early growth stages of cotton (up to squaring stage) has been studied in detail by Dr Khan. He found that all ages of mirids cause damage to young plants and damage by mirid nymphs is cumulative. Maximum damage occurs when the insect reaches the 4th and 5th nymphal stages. He also found that mirid feeding causes shedding of small and medium squares, and damaged large squares develop as ‘parrot beak’ bolls. Detailed studies at the boll stage, such as which stage of mirids is most damaging or which age boll is most vulnerable to feeding, is lacking. This information is a prerequisite to developing an IPM strategy for the pest in later crop growth stages. Understanding population change of the pest over time in relation to crop development is an important aspect for developing management strategies for the pest which is lacking for mirids in BollgardII. Predators and parasitoids are integral components of any IPM system and play an important part in regulating pest populations. Some generalist predators such as ants, spiders, damsel bugs and assassin bugs are known to predate on mirids. Nothing is known about parasitoids of mirids. Since green mirid (GM), Creontiades dilutus, is indigenous to Australia it is likely that we have one or more parasitoids of this mirid in Australia, but that possibility has not been investigated yet. The impact of the GVB adult parasitoid, Trichopoda giacomelli, has been studied by Dr Khan who found that the fly is established in the released areas and continues to spread. However, to get wider and greater impact, the fly should be released in new locations across the valleys. The insecticides registered for mirids and stinkbugs are mostly non-selective and are extremely disruptive to a wide range of beneficial insects. Use of these insecticides at stage I and II will minimise the impact of existing IPM programs. Therefore less disruptive control tactics including soft chemicals for mirids and stinkbugs are necessary. As with soft chemicals, salt mixtures, biopesticides based on fungal pathogens and attractants based on plant volatiles may be useful tools in managing mirids and stinkbugs with less or no disruption. Dr Khan has investigated salt mixture against mirids and GVB. While salt mixtures are quite effective and less disruptive, they are quite chemical specific. Not all chemicals mixed with salt will give the desired benefit. Therefore further investigation is needed to identify those chemicals that are effective with salt mixture against mirids and 3 of 37 GVB. Dr Caroline Hauxwell of DPI&F is working on fungal pathogen-based biopesticides against mirids and GVB and Drs Peter Gregg and Alice Del Socorro of Australian Cotton CRC are working on plant volatile-based attractants against mirids. Depending on their findings, inclusion of fungal-based biopestcides and plant volatile-based attractants in developing a management system against mirids and stinkbugs in cotton could be an important component of an IPM approach.

Organic diet development for black tiger prawns

The survival and growth of black tiger prawn (Penaeus monodon) juveniles (~3.3 g) were compared after feeding in tanks over one month with several prepared diets based on organically certified ingredients. The extrusion process in the manufacture of pelletised experimental diets was similar to processes used in commercial plants and was closely documented. The daily feeding rate (6% of starting mean body weight) was split equally into two feeds, one in the morning and one in the afternoon. All diets tested produced high survival (97-100%). A widely-used commercial Australian prawn feed was used as a control diet. It contained 41.2% protein with 29.5 g kg-1 lysine, and produced the highest (P<0.05) growth (117% weight gain). Three of the experimental organic diets tested (namely, 1. wheat + soy, 2. pig weaner diet + soy, and 3. pig weaner diet + dried fish waste) produced moderate growth (73–77% weight gain). These contained 33%, 36% or 31% protein, respectively, and produced better (P<0.05) growth than diets utilising a range of other prospective ingredients (eg: wheat + dried scallop gut, wheat + fish waste, wheat + chickpea, or wheat + macadamia meal, containing 23%, 25%, 29% or 24% protein, respectively). An unfed control-treatment produced the lowest (P<0.05) growth (4% weight gain). The water stability of the experimental diets that produced the best growth was poorer than the commercial diet, suggesting that improvements in this aspect of these organic feed’s manufacture could result in additional performance benefits and possibly reduced feed wastage. Analyses revealed a linear relationship between diet performance (in terms of weight gains) and the protein and lysine contents of diets. About 70% of diet performance was explained by these factors. The superior performance of the commercial diet could be attributed primarily to its formulation using mainly marine proteins, as well as a range of other unknown factors (commercial in confidence). These other factors range from use of feed attractants, better knowledge of ingredient nutrient availability, different extrusion conditions and the use of other unspecified micro-nutrients not present in the experimental diets. The organic diets studied still require a degree of fine-tuning before structured commercial uptake. This would sensibly include further detailed investigations of the composition and nutrient availabilities of these and other organic dietary ingredients, and refinement of the extrusion process for formulated diets.

Host Records of Fruit Flies in the South Pacific

Understanding the host range for all of the fruit fly species within the South Pacific region is vital to establishing trade and quarantine protocols. This is important for the countries within the region and their trade partners. A significant aspect of the Australian Centre for International Agricultural Research (ACIAR) and Regional Fruit Fly Projects (RFFP) has been host fruit collecting which has provided information on fruit fly host records in the seven participating countries. This work is still continuing in all project countries at different intensities. In the Cook Islands, Fiji, Tonga and Western Samoa, fruit surveys have assumed a quarantine surveillance role, with a focus on high risk fruits, such as guava, mango, citrus, bananas, cucurbits and solanaceous fruits. In the Solomon Islands, Vanuatu and the Federated States of Micronesia (FSM), fruit surveys are still at the stage where host ranges are far from complete. By the end of the current project a more complete picture of the fruit fly hosts in these countries will have been gained. A brief summary of the data collected to date is as follows: 23 947 fruit samples collected to date; 2181 positive host fruit records; 31 fruit fly species reared from fruit; 12 species reared from commercial fruit. A commercial fruit is classed as an edible fruit with potential for trade at either a local or international level. This allows for the inclusion of endemic fruit species that have cultural significance as a food source. On the basis of these results, there are fruit fly species of major economic importance in the South Pacific region. However, considerably more fruit survey work is required in order to establish a detailed understanding of all the pest species.

Complexity of coffee flavor: A compositional and sensory perspective

For the consumer, flavor is arguably the most important aspect of a good coffee. Coffee flavor is extremely complex and arises from numerous chemical, biological and physical influences of cultivar, coffee cherry maturity, geographical growing location, production, processing, roasting and cup preparation. Not surprisingly there is a large volume of research published detailing the volatile and non-volatile compounds in coffee and that are likely to be playing a role in coffee flavor. Further, there is much published on the sensory properties of coffee. Nevertheless, the link between flavor components and the sensory properties expressed in the complex matrix of coffee is yet to be fully understood. This paper provides an overview of the chemical components that are thought to be involved in the flavor and sensory quality of Arabica coffee.

Host specificity studies on Gynaikothrips (Thysanoptera: Phlaeothripidae) associated with leaf galls of cultivated Ficus (Rosales: Moraceae) trees

Host specificity tests on Gynaikothrips ficorum (Marchal) and Gynaikothrips uzeli (Zimmerman) (Thysanoptera: Phlaeothripidae) have shown that under experimental conditions, G. ficorum will induce leaf galls on both Ficus benjamina L. and Ficus microcarpa L. f. (Rosales: Moraceae), but G. uzeli will induce galls only on F. benjamina. A further interesting aspect of the results is that gall induction by G. uzeli on F. benjamina appears to have been suppressed in the presence of F. microcarpa plants in the same cage. Liothrips takahashii (Moulton) (Thysanoptera: Phlaeothripidae), an inquiline in the galls of these Gynaikothrips, is reported for the first time from Australia, mainland China, Malaysia, Costa Rica, and western USA.