Coliforms in processed mango: Significance and control

The aims of this investigation were to enumerate coliforms in fresh mangoes, puree, cheeks, and cheeks-in-puree in order to determine the source of these organisms in the processed products, to determine methods for their control, and to identify coliforms isolated from cheeks-in-puree to determine whether they have any public health significance. Product from four processors was tested on two occasions. The retail packs of cheeks-in-puree having the highest coliform counts were those in which raw puree was added to the cheeks. Coliform counts in these samples ranged between 1.4 × 103 and 5.4 × 104 cfu/g. Pasteurisation reduced the coliform count of raw puree to < 5 cfu/g. Forty-seven percent of the 73 colonies, isolated as coliforms on the basis of their colony morphology on violet red bile agar, were identified as Klebsiella pneumoniae using the ATB 32E Identification System. Klebsiella strains were tested for growth at 10 °C, faecal coliform response, and fermentation of -melizitose, to differentiate the three phenotypically similar strains, K. pneumoniae, K. terrigena and K planticola. Results indicated that 41% of K. pneumoniae isolates gave reactions typical of K. pneumoniae. A further 44% of strains gave an atypical reaction pattern for these tests and were designated ‘psychrotrophic’ K. pneumoniae. Klebsiella pneumoniae counts of between 2.1 × 103 and 4.9 × 104 cfu/g were predicted to occur in the retail packs of mango cheeks-in-puree produced by the processors who constituted this product with raw puree. In view of the opportunistic pathogenic nature of K. pneumoniae, its presence in these products is considered undesirable and steps, such as pasteurisation of puree, should be taken in order to inactivate it

Differentiation of Indian, East Timorese, Papuan and Floridian Candidatus Liberibacter asiaticus' isolates on the basis of simple sequence repeat and single nucleotide polymorphism profiles at 25 loci

Japanese isolates of Candidatus Liberibacter asiaticus have been shown to be clearly differentiated by simple sequence repeat (SSR) profiles at four loci. In this study, 25 SSR loci, including these four loci, were selected from the whole-genome sequence and were used to differentiate non-Japanese samples of Ca. Liberibacter asiaticus (13 Indian, 3 East Timorese, 1 Papuan and 8 Floridian samples). Out of the 25 SSR loci, 13 were polymorphic. Dendrogram analysis using SSR loci showed that the clusters were mostly consistent with the geographical origins of the isolates. When single nucleotide polymorphisms (SNPs) were searched around these 25 loci, only the upstream region of locus 091 exhibited polymorphism. Phylogenetic tree analysis of the SNPs in the upstream region of locus 091 showed that Floridian samples were clustered into one group as shown by dendrogram analysis using SSR loci. The differences in nucleotide sequences were not associated with differences in the citrus hosts (lime, mandarin, lemon and sour orange) from which the isolates were originally derived.

Neospora caninum and reproductive wastage in extensively managed Queensland beef herds

Objective To compare reproduction in extensively managed, tropically adapted beef cows that were either seropositive or seronegative to Neospora caninum. Design Longitudinal study of cows within management groups. Methods Compare pregnancy with weaning outcomes for 502 seropositive and 3255 seronegative cows in 25 management groups. Results We found N. caninum in all herds, with an average of 20% of 2640 tested animals seropositive within management group; prevalence varied between 0% and 94%. At 7 of 10 sites assessed, there was evidence of horizontal transmission of N. caninum. There was no overall difference in pregnancy rate (79% vs 75%; P > 0.05), reproductive wastage after confirmed pregnancy diagnosis (11% vs 10%; P > 0.05) or weaning rate (67% vs 68%; P > 0.05) between seronegative and seropositive cows, respectively. In one herd where a combination of risk factors for N. caninum was present, a significant reduction in pregnancy rate occurred after the 6 months mating (85% vs 69%; P < 0.05). The fetal and calf losses observed were lowest in south-east Queensland (4.3% of 117 pregnancies), highest in north-west Queensland (15.5% of 413 pregnancies) and intermediate in north-east Queensland (10.2% of 1625 pregnancies). Other infectious agents that are known to cause reproductive wastage were endemic in many herds, though none appeared to cause significant fetal or calf loss in this study. Conclusion Despite a high prevalence of N. caninum, there was no apparent effect on beef cattle reproduction, but there is potential to cause reproductive wastage if known risk factors to neosporosis are in effect.

Structural Veneer Based Composite Products from Hardwood Thinning - Part II: Testing of Hollow Utility Poles

Australian utility pole network is aging and reaching its end of life, with 70% of the 5 million poles currently in-service nationally installed within the 20 years following the end of World War II. The estimated investment required for the replacement or remedial maintenance of the aging 3.5 millions poles is as high as 1.75 billion dollars. Additionally, an estimated 21,700 high-durability new poles are required each year, representing further investment of 13.5 million dollars per year. Yet, agreements which progressively phase out logging of native forests around Australia have been signed, giving the industry about 25 years to make the transition from Crown native forests to plantations and private forests. As utility poles were traditionally cut from native forest hardwood species, finding solutions to source new poles currently presents a challenge. This paper presents tests on Veneer Based Composite hardwood hollow utility poles manufactured from Gympie messmate (Eucalyptus cloeziana) plantation thinning. Small diameter poles of nominal 115 mm internal diameter and 15 mm wall-thickness were manufactured in two half-poles butt jointed together, using 9 veneers per halfpole. The poles were tested in bending and shear, and experimental test results are presented. The mechanical performance of the hollow poles is discussed and compared to hardwood poles cut from mature trees and of similar size. Future research and different options for improving the current concept are proposed in order to provide a more reliable and cost effective technical solution to the current shortage of utility poles. © RILEM 2014.