Taxonomy, distribution and ecology of Zoysia macrantha desv., an Australian native species with turf breeding potential

Only three of the 11 species in the genus Zoysia Willd. have thus far contributed to commercially available turfgrass varieties. One of the neglected taxa is Z. macrantha Desv., an Australian native species further divided into two subspecies. The coarser Z. macrantha subsp. macrantha occurs on sand dunes, headlands and tidal areas along eastern and southeastern coasts from about 23 to 38°S latitude. The shorter, denser-growing Z. macrantha subsp. walshii M.E. Nightingale is found on the southern mainland (South Australia and Victoria from longitude 137° to 148°E and at latitudes higher than 36°S), adjacent offshore islands, and northern, eastern and central Tasmania to 43°S growing on the edges of coastal, sub-coastal and even inland salt lakes, in riverine environments, and from moist grassy depressions (both coastal and inland) to rocky headlands. The latter subspecies has the more discontinuous and specialised distribution, largely determined by the need for an appropriate level of peat, clay or silt in the soil to maintain adequate moisture during the dry summers in southern Australia while at the same time avoiding anything more than temporary waterlogging. It grows on low fertility soils ranging from strongly acid to neutral or mildly alkaline, and is often very closely grazed by marsupials. Both subspecies are salt and drought tolerant, but not notably shade tolerant. Their potential to add greater drought tolerance in particular to the Asian Zoysia material in current use through future breeding programs is discussed.

Comparative performance of Corymbia hybrids and parental species in subtropical Queensland and implications for breeding and deployment.

Eighty six full-sib Corymbia F1 hybrid families (crosses between C. torelliana and four spotted gum taxa: C. citriodora subsp. variegata, C. citriodora subsp. citriodora, C. henryi and C. maculata), were planted in six trials across six disparate sites in south-eastern Queensland to evaluate their productivity and determine their potential utility for plantation forestry. In each trial, the best-growing 20% of hybrid families grew significantly faster (P=0.05) than open-pollinated seedlots of the parent species Corymbia citriodora subsp. variegata, ranging from 107% to 181% and 127% to 287% of the height and diameter respectively. Relative performance of hybrid families growing on more than one site displayed consistency in ranking for growth across sites and analysis showed low genotype-by-environment interaction. Heritability estimates based on female and male parents across two sites at age six years for height and diameter at breast height, were high (0.62±0.28 to 0.64±0.35 and 0.31±0.21 to 0.69±0.37 respectively), and low to moderate (0.03±0.04 to 0.33±0.22) for stem straightness, branch size, incidence of ramicorns, and frost and disease resistance traits at ages one to three years. The proportion of dominance variance for height and diameter had reduced to zero by age six years. Based on these promising results, further breeding and pilot-scale family forestry and clonal forestry deployment is being undertaken. These results have also provided insights regarding the choice of a future hybrid breeding strategy.

Resin defect impacts on the value of graded recovery and evaluation of technologies for internal defect detection in slash pine logs.

The key outcome will be to identify a technology that is practical to use to scan logs identified by the modelling as suspect or marginal for sawing and to confirm their unsuitability for value adding sawing by internal scanning.

An evaluation of electrofishing as a control measure for an invasive tilapia (Oreochromis mossambicus) population in northern Australia.

Combating the spread of invasive fish is problematic, with eradication rarely possible and control options varying enormously in their effectiveness. In two small impoundments in north-eastern Australia, an electrofishing removal program was conducted to control an invasive tilapia population. We hypothesised that electrofishing would reduce the population density of Oreochromis mossambicus (Mozambique tilapia), to limit the risk of downstream spread into areas of high conservation value. We sampled by electrofishing monthly for 33 months. Over this period, there was an 87% decline in catch per unit effort (CPUE) of mature fish, coupled with a corresponding increase of 366% in the number of juveniles, suggesting a density-dependent response in the stock-recruitment relationship for the population. Temperature was inversely related to CPUE (r=0.43, lag=10 days), implying greater electrofishing efficiency in cooler months. The reduction in breeding stock is likely to reduce the risk of spread and render the population vulnerable to other control measures such as netting and/or biological control. Importantly, the current study suggests routine electrofishing may be a useful control tool for invasive fish in small impoundments when the use of more destructive techniques, such as piscicides, is untenable.

Membrane fractionation technologies for high quality mill sugar and value-added by products - an integrated sugar production process concept model.

Membrane filtration technology has been proven to be a technically sound process to improve the quality of clarified cane juice and subsequently to increase the productivity of crystallisation and the quality of sugar production. However, commercial applications have been hindered because the benefits to crystallisation and sugar quality have not outweighed the increased processing costs associated with membrane applications. An 'Integrated Sugar Production Process (ISPP) Concept Model' is proposed to recover more value from the non-sucrose streams generated by membrane processing. Pilot scale membrane fractionation trials confirmed the technical feasibility of separating high-molecular weight, antioxidant and reducing sugar fractions from cane juice in forms suitable for value recovery. It was also found that up to 40% of potassium salts from the juice can be removed by membrane application while removing the similar amount of water with potential energy saving in subsequent evaporation. Application of ISPP would allow sugar industry to co-produce multiple products and high quality mill sugar while eliminating energy intensive refining processes.

Wood properties and processing outcomes for plantation grown African mahogany (Khaya senegalensis) trees from Clare, Queensland (18 and 20 year-old trees) and Katherine, Northern Territory (14 year-old trees).

Khaya senegalensis, African mahogany, a high-value hardwood, was introduced in the Northern Territory (NT) in the 1950s; included in various trials there and at Weipa, Q in the 1960s-1970s; planted on ex mine sites at Weipa (160 ha) until 1985; revived in farm plantings in Queensland and in trials in the NT in the 1990s; adopted for large-scale, annual planting in the Douglas-Daly region, NT from 2006 and is to have the planted area in the NT extended to at least 20,000 ha. The recent serious interest from plantation growers, including Forest Enterprises Australia Ltd (FEA), has seen the establishment of some large scale commercial plantations. FEA initiated the current study to process relatively young plantation stands from both Northern Territory and Queensland plantations to investigate the sawn wood and veneer recovery and quality from trees ranging from 14 years (NT – 36 trees) to 18-20 years (North Queensland – 31 trees). Field measures of tree size and straightness were complemented with log end splitting assessment and cross-sectional disc sample collection for laboratory wood properties measurements including colour and shrinkage. End-splitting scores assessed on sawn logs were relatively low compared to fast grown plantation eucalypts and did not impact processing negatively. Heartwood proportion in individual trees ranged from 50% up to 92 % of butt cross-sectional disc area for the visually-assessed dark coloured central heartwood and lighter coloured transition wood combined. Dark central heartwood proportion was positively related to tree size (R2 = 0.57). Chemical tests failed to assist in determining heartwood – sapwood boundary. Mean basic density of whole disc samples was 658 kg/m3 and ranged among trees from 603 to 712 kg/m3. When freshly sawn, the heartwood of African mahogany was orange-red to red. Transition wood appeared to be pinkish and the sapwood was a pale yellow colour. Once air dried the heartwood colour generally darkens to pinkish-brown or orange-brown and the effect of prolonged time and sun exposure is to darken and change the heartwood to a red-brown colour. A portable colour measurement spectrophotometer was used to objectively assess colour variation in CIE L*, a* and b* values over time with drying and exposure to sunlight. Capacity to predict standard colour values accurately after varying periods of direct sunlight exposure using results obtained on initial air-dried surfaces decreased with increasing time to sun exposure. The predictions are more accurate for L* values which represent brightness than for variation in the a* values (red spectrum). Selection of superior breeding trees for colour is likely to be based on dried samples exposed to sunlight to reliably highlight wood colour differences. A generally low ratio between tangential and radial shrinkages was found, which was reflected in a low incidence of board distortion (particularly cupping) during drying. A preliminary experiment was carried out to investigate the quality of NIR models to predict shrinkage and density. NIR spectra correlated reasonably well with radial shrinkage and air dried density. When calibration models were applied to their validation sets, radial shrinkage was predicted to an accuracy of 76% with Standard Error of Prediction of 0.21%. There was also a strong predictive power for wood density. These are encouraging results suggesting that NIR spectroscopy has good potential to be used as a non-destructive method to predict shrinkage and wood density using 12mm diameter increment core samples. Average green off saw recovery was 49.5% (range 40 to 69%) for Burdekin Agricultural College (BAC) logs and 41.9% (range 20 to 61%) for Katherine (NT) logs. These figures are about 10% higher than compared to 30-year-old Khaya study by Armstrong et al. (2007) however they are inflated as the green boards were not docked to remove wane prior to being tallied. Of the recovered sawn, dried and dressed volume from the BAC logs, based on the cambial face of boards, 27% could potentially be used for select grade, 40% for medium feature grade and 26% for high feature grades. The heart faces had a slightly higher recovery of select (30%) and medium feature (43%) grade boards with a reduction in the volume of high feature (22%) and reject (6%) grade boards. Distribution of board grades for the NT site aged 14 years followed very similar trends to those of the BAC site boards with an average (between facial and cambial face) 27% could potentially be used for select grade, 42% for medium feature grade, 26% for high feature grade and 5% reject. Relatively to some other subtropical eucalypts, there was a low incidence of borer attack. The major grade limiting defects for both medium and high feature grade boards recovered from the BAC site were knots and wane. The presence of large knots may reflect both management practices and the nature of the genetic material at the site. This stand was not managed for timber production with a very late pruning implemented at about age 12 years. The large amount of wane affected boards is indicative of logs with a large taper and the presence of significant sweep. Wane, knots and skip were the major grade limiting defects for the NT site reflecting considerable amounts of sweep with large taper as might be expected in younger trees. The green veneer recovered from billets of seven Khaya trees rotary peeled on a spindleless lathe produced a recovery of 83% of green billet volume. Dried veneer recovery ranged from 40 to 74 % per billet with an average of 64%. All of the recovered grades were suitable for use in structural ply in accordance to AS/NZ 2269: 2008. The majority of veneer sheets recovered from all billets was C grade (27%) with 20% making D grade and 13% B grade. Total dry sliced veneer recovery from the logs of the two largest logs from each location was estimated to be 41.1%. Very positive results have been recorded in this small scale study. The amount of colour development observed and the very reasonable recoveries of both sawn and veneer products, with a good representation of higher grades in the product distribution, is encouraging. The prospects for significant improvement in these results from well managed and productive stands grown for high quality timber should be high. Additionally, the study has shown the utility of non-destructive evaluation techniques for use in tree improvement programs to improve the quality of future plantations. A few trees combined several of the traits desired of individuals for a first breeding population. Fortunately, the two most promising trees (32, 19) had already been selected for breeding on external traits, and grafts of them are established in the seed orchard.

Develop added value uses of high anti-bacterial honey

Honey is valued for its medicinal properties. There interest from industry to develop a rapid method to detect the bioactivity of honey and also to develop value added products from high antibacterial honey.

Smart sorbers - value adding spent litter fertiliser. A pilot trial

Currently spent litter is not a balanced fertiliser. This project is a first step in improving the ability to reduce environmental contamination and to more fully realise the full fertilizer and soil amendment value of this material.

Breeding Low Chill high quality stonefruit

Breeding Low Chill high quality stonefruit.

ACIAR 9995 Improving the value chain for plantation-grown sawn wood

To improve the yield of marketable high value sawn and/or veneer timber from young plantation grown eucalypts: through the greater understanding and management of growth stresses; grain angle; juvenile wood; and other important wood properties.

High-value wood products from sub-tropical plantations

To refine the emerging silvicultural systems for sub-tropical eucalypt plantations to produce logs of acceptable dimensions and quality for processing into high-value solid and engineered wood products, while maintaining financial attractiveness for growers. The available resources are focussed primarily on sub-tropical Corymbia plantings.

Tropical peach breeding and evaluation

Breeding new peach and nectarine cultivars that are adapted to tropical climates and produce fruit of high quality.

Improved domestic profitability and export competitiveness of selected fruit value chains in the southern Philippines and Australia program

The goal of the Program is to contribute to economic growth in the Philippines through increased income and improved livelihoods of tropical fruit growers in southern Philippines. The purpose of the Program is to improve the smallholder and industry profitability and export competitiveness of selected tropical fruits industries in the southern Philippines. Fruit crops to be targeted are mango, papaya, durian and jackfruit. The primary audience for the outcomes of this Program are medium to large scale commercial fruit growers and farmers predominantly in the regions of Leyte (VIII), northern Mindanao/Cagayan de Oro (X) and southern Mindanao/Davao (XI).

Marker Assisted Breeding Support for Tropical Horticulture and Forestry in far north Queensland

Molecular marker development for tropical fruit and forestry species.

Improving added value and small medium enterprises capacity in the utilisation of plantation timber for furniture production in Jepara region

Improving added value and Small Medium Enterprises capacity in the utilisation of plantation timber for furniture production in Jepara region of Indonesia: improving recovery, design, manufacturing, R&D and training capacities.