A convenient sample preparation protocol for scanning electron microscope examination of xylem-occluding bacterial biofilm on cut flowers and foliage

Microbes and their exopolysaccharides (EPS) can block xylem vessels, thereby increasing the hydraulic resistance and decreasing the vase life of cut flowers and foliage. Scanning electron microscopy (SEM) provides a powerful tool for investigation of bacteria-induced xylem occlusion. However, conventional preparation protocols for SEM involving chemicals can cause loss of hydrated EPS material, and thereby damage the bacterial biofilms during dehydration. A modified chemical fixation protocol involving pre-fixation with 75 mM lysine plus 2.5% glutaraldehyde followed by the normal fixation in 3% glutaraldehyde was, therefore, tested for improved preservation of bacterial biofilm at the stem-ends of cut Acacia holosericea foliage stems. Stem-end segments with different stages of bacterial growth were obtained from stems stood into water. The lysine-based protocol was compared with four other processing protocols of critical point drying (CPD) without fixation (control), freeze-drying (FD), conventional chemical fixation followed by drying with hexamethyldisilazane (HMDS), and conventional chemical fixation with CPD. The non-fixed control. FD and the glutaraldehyde fixation with HMDS drying gave poor preservation of hydrated material, including bacterial EPS. Conventional glutaraldehyde fixation followed by CPD was superior to these three methods in terms of better preserving the EPS. However, this fourth method gave condensation of biofilms during dehydration. In contrast, the modified lysine-based protocol resulted in superior preservation of EPS and biofilm structure. Thus, this fifth method was the most appropriate for examination of bacterial stem-end blockage in cut ornamentals. (C) 2012 Elsevier B.V. All rights reserved.

Postharvest physiology and volatile production by flowers of Ptilotus nobilis

Ptilotus nobilis (Lindl.) F. Muell. has potential in the floriculture industries as a cut flower crop. Ethylene production and respiration rates, fresh weight changes and volatile scent production from cut inflorescences of P. nobilis cultivars Passion (dark pink flowers) and Purity (white-green flowers) were measured during vase life. Inflorescence weight loss was significant (P<0.001) during vase life with wilting and colour loss being the primary reasons for loss of vase life. Inflorescences ready for the cut market stored and at 22 degrees C had vase lives of >12 d. Ethylene production by inflorescences was low to negligible. Treatment with silverthiosulphate (STS) and ethylene had no effects on vase life. Evidently, ethylene did not play a role in determining the postharvest longevity of cut P. nobilis flowers. Respiration rates of inflorescences were high at harvest (>700 mg CO2 kg(-1) FW h(-1)) and declined gradually there-after during vase life. Total volatile emissions followed a similar pattern. For Passion, respiration rates of immature florets were significantly greater (P=0.02) than florets from other developmental stages while the calyx produced the most CO2. For Purity, respiration rates of florets of different maturities did not differ and the reproductive tissue produced the most CO2. Only fully opened mature florets with their stigma and anthers revealed, emitted significant quantities of volatiles (P<0.001) and primarily from the calyx tissue for both cultivars. The individual volatiles differed somewhat for the two cultivars. However, both produced significant quantities of benzaldehyde, 3,5-dimethoxytoluene and benzyl alcohol. These. compounds have previously been associated with desirable floral scent. (C) 2013 Elsevier B.V. All rights reserved.

A comparison of stocking methods for beef production in northern Australia: pasture and soil surface condition responses

Historical stocking methods of continuous, season-long grazing of pastures with little account of growing conditions have caused some degradation within grazed landscapes in northern Australia. Alternative stocking methods have been implemented to address this degradation and raise the productivity and profitability of the principal livestock, cattle. Because information comparing stocking methods is limited, an evaluation was undertaken to quantify the effects of stocking methods on pastures, soils and grazing capacity. The approach was to monitor existing stocking methods on nine commercial beef properties in north and south Queensland. Environments included native and exotic pastures and eucalypt (lighter soil) and brigalow (heavier soil) land types. Breeding and growing cattle were grazed under each method. The owners/managers, formally trained in pasture and grazing management, made all management decisions affecting the study sites. Three stocking methods were compared: continuous (with rest), extensive rotation and intensive rotation (commonly referred to as 'cell grazing'). There were two or three stocking methods examined on each property: in total 21 methods (seven continuous, six extensive rotations and eight intensive rotations) were monitored over 74 paddocks, between 2006 and 2009. Pasture and soil surface measurements were made in the autumns of 2006, 2007 and 2009, while the paddock grazing was analysed from property records for the period from 2006 to 2009. The first 2 years had drought conditions (rainfall average 3.4 decile) but were followed by 2 years of above-average rainfall. There were no consistent differences between stocking methods across all sites over the 4 years for herbage mass, plant species composition, total and litter cover, or landscape function analysis (LFA) indices. There were large responses to rainfall in the last 2 years with mean herbage mass in the autumn increasing from 1970 kg DM ha(-1) in 2006-07 to 3830 kg DM ha(-1) in 2009. Over the same period, ground and litter cover and LFA indices increased. Across all sites and 4 years, mean grazing capacity was similar for the three stocking methods. There were, however, significant differences in grazing capacity between stocking methods at four sites but these differences were not consistent between stocking methods or sites. Both the continuous and intensive rotation methods supported the highest average annual grazing capacity at different sites. The results suggest that cattle producers can obtain similar ecological responses and carry similar numbers of livestock under any of the three stocking methods.

Interaction between production characteristics and postharvest performance and practices for fresh fruit

Significant interactions have been demonstrated between production factors and postharvest quality of fresh fruit. Accordingly, there is an attendant need for adaptive postharvest actions to modulate preharvest effects. The most significant preharvest effects appear to be mediated through mineral nutrition influences on the physical characteristics of fruit. Examples of specific influencers include fertilisers, water availability, rootstock, and crop load effects on fruit quality attributes such as skin colour, susceptibility to diseases and physiological disorders, and fruit nutritional composition. Also, rainfall before and during harvest can markedly affect fruit susceptibility to skin blemishes, physical damage, and diseases. Knowledge of preharvest-postharvest interactions can help determine the basis for variability in postharvest performance and thereby allow refinement of postharvest practices to minimise quality loss after harvest. This knowledge can be utilised in predictive management systems. Such systems can benefit from characterisation of fruit nutritional status, particularly minerals, several months before and/or at harvest to allow informed decisions on postharvest handling and marketing options. Other examples of proactive management practices include adjusting harvesting and packing systems to account for rainfall effects before and/or during harvest. Improved understanding of preharvest-postharvest interactions is contributing to the delivery of consistently higher quality of fruit to consumers. This paper focuses on the state of knowledge for sub-tropical and tropical fruits, in particular avocado and mango.

Cu2+ inhibition of gel secretion in the xylem and its potential implications for water uptake of cut Acacia holosericea stems

Maintaining a high rate of water uptake is crucial for maximum longevity of cut stems. Physiological gel/tylosis formation decreases water transport efficiency in the xylem. The primary mechanism of action for post-harvest Cu2+ treatments in improving cut flower and foliage longevity has been elusive. The effect of Cu2+ on wound-induced xylem vessel occlusion was investigated for Acacia holosericea A. Cunn. ex G. Don. Experiments were conducted using a Cu2+ pulse (5 h, 2.2 mM) and a Cu2+ vase solution (0.5 mM) vs a deionized water (DIW) control. Development of xylem blockage in the stem-end region 10 mm proximal to the wounded stem surface was examined over 21 days by light and transmission electron microscopy. Xylem vessels of stems stood into DIW were occluded with gels secreted into vessel lumens via pits from surrounding axial parenchyma cells. Gel secretion was initiated within 1-2 days post-wounding and gels were detected in the xylem from day 3. In contrast, Cu2+ treatments disrupted the surrounding parenchyma cells, thereby inhibiting gel secretion and maintaining the vessel lumens devoid of occlusions. The Cu2+ treatments significantly improved water uptake by the cut stems as compared to the control. © 2013 Scandinavian Plant Physiology Society.

Boronia heterophylla vase life is influenced more by ethylene than by bacterial numbers or vase solution pH

Bacterial proliferation in both vase solutions and in cut flower stems has been implicated in reducing the vase life of numerous genera. Boronia heterophylla F. Muell. (Red Boronia) vase life was assessed at two stages of floral maturity for nine vase solution treatments covering a pH range of 2.5-5.7. Vase life for advanced harvest maturity stems ranged from 4.2 d in 10 mM citric acid + 50 mg L-1 chlorine (pH 2.5) to 12.9 d after STS pulsing (pH 5.7). For normal harvest maturity stems, the corresponding range was 5.8-19.0 d, respectively. Vase solutions containing 50 mg L-1 chlorine biocide resulted in decreased longevity. In contrast, pulsing with the ethylene-binding inhibitor, STS, significantly increased vase life. The number of bacteria in the vase solutions after 11 d was determined in stems of advanced maturity. The solution with the greatest number of bacteria, 4.0 x 10(10) cfu mL(-1), was water used after STS pulsing and in which the flowers lasted longest. Vase solution bacteria were enumerated on days 0,3, 6, 9 and 12 of the vase period with stems of normal harvest maturity. There was no relationship between vase life and vase solution bacterial numbers ((R) over bar (2) = 0.000). Moreover, there was a negative relationship between numbers of bacteria in basal 0-5 cm stem segments and vase life. As no correlations were evident between longevity and either the pH or vase solution bacterial numbers, B. heterophylla vase life was evidently limited principally by ethylene action. (C) 2013 Elsevier B.V. All rights reserved.

A retrospective study of vase life determinants for cut Acacia holosericea foliage

Short and variable vase life of cut Acacia holosericea foliage stems limits its commercial potential. Retrospective evaluation of factors affecting the vase life of this cut foliage line was assessed using primary data collected from 30 individual experiments. These data had been collected by four different researchers over 17 months, from late Summer to mid Winter across two consecutive years. Vase life data of cut A. holosericea stems held in deionised water (DIW) was analysed for general vase life variation and to define the most influential factor affecting vase life of the cut stems. Meanwhile, vase life of cut stems exposed to various chemical and physical postharvest treatments was analysed using meta-analysis to evaluate their efficacy in prolonging vase life of the stems. The overall mean vase life (±standard deviation) of cut A. holosericea stems was 6.4 ± 1.2 days (n = 30 trials). Longer vase life of ≥7 days was obtained from cut stems harvested at vegetative and flowering stage, which was between Summer and Autumn. Cut stems harvested at fruiting stage, between Winter and Spring displayed shorter vase life of ≤5.5 days. Mixed model analysis indicated that vase life variation of the cut stems was mostly determined by season (P < 0.001). In averaged, postharvest treatments increased vase life 1.4-fold compared to stems in DIW, with 68.32% had a large positive treatment effect size (d). Among the treatments, nano silver (NS) and copper (Cu2+) were the most beneficial to vase life. Retrospective analysis was found to be beneficial for identifying conditions and targeting practices to maximise the vase life of cut A. holosericea and, potentially for other species.

Postharvest manual answers many questions

Many authors have noted that consumer confidence in buying fresh flowers is strongly related to their perceived value in that quality and vase life must be high and consistent over time for consumers to repeat buy. Growers, wholesalers, exporters and retailers seek practical information about recommended handling and treatments at the harvest and postharvest stages, including that relating to flowers native to Australia and South Africa ("wildflowers"). This information is essential for products to be of high quality with an acceptable vase life for the end consumer, especially if exported. Published postharvest manuals generally focus on traditional flower crops and so rarely include many, or any, wildflowers. A manual entitled Postharvest Handling of Australian flowers from Native Plants and Related Species was published in 2002 and addressed this gap, but required updating. This situation presented an opportunity to provide in-depth information to compliment the Australian wildflower quality specifications (see accompanying paper in the same volume), and to assemble the latest knowledge on wildflower quality and postharvest issues. The resultant manual contains extensive information about harvesting, quality issues and recommended postharvest care focussed on wildflowers. Much of the information is documented for the first time, being based on the most up to date research and development (R&D) as well as practical experience of the floral supply chain, researchers and other technical experts. The manual provides practical and detailed information on postharvest treatment of fresh wildflowers for growers, florists, wholesalers and exporters to use on a daily basis. It discusses the many unique features of wildflowers that must be understood and managed in order to maximise their quality and vase life after marketing and export. The manual also includes postharvest advice for 16 flower- and foliage lines for which quality specifications were not produced. This advice is presented according to the same template as the specifications.

Karyological Characteristics of Lilium ledebourii Boiss and Lilium longiflorum Thunb.

The karyological characteristics of two Lilium species were investigated by aceto-ferric-hematoxylin staining. Chromosome characteristics, including the number and length of the chromosomes, length of their long and short arms, length of the total set of chromosomes, the arm ratio index and relative lengths of chromosome, were measured based on averages for five different metaphase cells. Both species are diploid (2n=2x=24). The karyotype of Lilium ledebourii consisted of 1 pair of metacentric, 4 pairs of submetacentric, 3 pairs of acrocentric and 4 pairs of subtelocentric chromosomes. The karyotype of Lilium longiflorum was comprised of 1 pair of metacentric, 4 pairs of acrocentric and 7 pairs of subtelocentric chromosomes. Chromosomes 5 and 7 in Lilium ledebourii and chromosomes 6 in Lilium longiflorum had a satellite. Karyotypes were classified as 3A by Stebbins classification.

Biomass for aviation fuel production in the Fitzroy Basin, Queensland: a preliminary assessment of native and plantation forest potential

SummaryThis scoping study assesses the contribution that woody biomass could make to feedstock supply for an aviation biofuel industry in Queensland. The inland 600?900 mm rainfall zone, including the Fitzroy Basin region, is identified as an area that is particularly worthy of closer study as it has potential for supply of woody biomass from existing native regrowth (brigalow and other species) as well as from new plantings. New analyses carried out for this study of Corymbia citriodora subsp. variegata trials suggest biomass plantings could produce harvestable yield of aboveground dry mass of about 85 t ha?1 over a 10-year rotation at relatively low-rainfall (600?750 mm mean annual precipitation) sites and about 115 t ha?1 at medium-rainfall (750?900 mm) sites. Estimates of productivity for native regrowth suggest potential productivity should be around 40 t ha?1 during the initial decade after clearing when systems are managed for bioenergy rather than grazing. In this paper, potential production systems are described, and sustainability issues are briefly considered. It is concluded that more detailed studies focused particularly on biomass production would be worthwhile, and further research requirements are briefly discussed.

Postharvest physiology and volatile production by flowers of Ptilotus nobilis

Ptilotus nobilis (Lindl.) F. Muell. has potential in the floriculture industries as a cut flower crop. Ethylene production and respiration rates, fresh weight changes and volatile scent production from cut inflorescences of P. nobilis cultivars Passion (dark pink flowers) and Purity (white-green flowers) were measured during vase life. Inflorescence weight loss was significant (P < 0.001) during vase life with wilting and colour loss being the primary reasons for loss of vase life. Inflorescences ready for the cut market stored and at 22 °C had vase lives of >12 d. Ethylene production by inflorescences was low to negligible. Treatment with silverthiosulphate (STS) and ethylene had no effects on vase life. Evidently, ethylene did not play a role in determining the postharvest longevity of cut P. nobilis flowers. Respiration rates of inflorescences were high at harvest (>700 mg CO2 kg−1 FW h−1) and declined gradually thereafter during vase life. Total volatile emissions followed a similar pattern. For Passion, respiration rates of immature florets were significantly greater (P = 0.02) than florets from other developmental stages while the calyx produced the most CO2. For Purity, respiration rates of florets of different maturities did not differ and the reproductive tissue produced the most CO2. Only fully opened mature florets with their stigma and anthers revealed, emitted significant quantities of volatiles (P < 0.001) and primarily from the calyx tissue for both cultivars. The individual volatiles differed somewhat for the two cultivars. However, both produced significant quantities of benzaldehyde, 3,5-dimethoxytoluene and benzyl alcohol. These compounds have previously been associated with desirable floral scent.