Prevalence Of Shear Banding In Compression Of Zr41Ti14Cu12.5Ni10Be22.5 Pillars As Small As 150 Nm In Diameter

Recently, the size dependence of mechanical behaviors, particularly the yield strength and plastic deformation mode, of bulk metallic glasses (BMG) has created a great deal of interest. Contradicting conclusions have been drawn by different research groups, based on various experiments on different BMG systems. Based on in situ compression transmission electron microscopy (TEM) experiments on Zr41Ti14Cu12.5Ni10Be22.5 (Vit 1) nanopillars, this paper provides strong evidence that shear banding still prevails at specimen length scales as small as 150 nm in diameter. This is supported by in situ and ex situ images of shear bands, and by the carefully recorded displacement bursts under load control its well as load drops under displacement control. Finite element modeling of the stress state within the pillar shows that the unavoidable geometry constraints accompanying such experiments impart a strong effect on the experimental results, including non-uniform stress distributions and high level hydrostatic pressures. The seemingly improved compressive ductility is believed to be due to such geometry constraints. Observations underscore the notion that the mechanical behavior of metallic glasses, including strength and plastic deformation mode, is size independent at least in Vit 1. (C) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effect of coal-over-coal reburn on furnace temperature and heat flux distributions in 1 MW tangentially fired furnace

The furnace temperature and heat flux distributions of 1 MW tangentially fired furnace were studied during coal-over-coal reburn, and the influences of the position of reburn nozzle and reburn fuel fraction on furnace temperature and heat flux distributions were investigated. Compared with the baseline, the flue gas temperature is 70–90 C lower in primary combustion and 130–150 C higher at furnace exit, and the variations of the flue gas temperature distributions along furnace height are slower. The temperature distribution along the width of furnace wall decreases with the increase of the relative furnace height. In the primary combustion zone and the reburn zone, the temperature and heat flux distributions of furnace wall are much non-uniform and asymmetric along the width of furnace wall, those of furnace wall in the burnout zone are relatively uniform, and the temperature non-uniformity coefficients of the primary combustion zone, the reburn zone and the burnout zone are 0.290, 0.100 and 0.031, respectively.

端面抽运的Tm:YAP薄片板条激光器的研究

2μm激光器由于其在遥感、雷达和医疗等领域具有重要的应用前景而受到越来越广泛的重视。Tm3+具有长的荧光寿命,且其吸收带与商用的激光二极管相匹配。YAP具有与YAG近似的机械和热性能,其双折射特性使得Tm:YAP激光器可以直接得到线偏振的激光输出,并且可以降低热退偏效应。795nm连续抽运光经透镜组耦合进薄片板条1mm×5mm晶体端面,采用平凹腔结构,分析比较了1%,4%和5%掺杂浓度的Tm:YAP的激光特性。

Passive Q-switching of short-length Tm3+-doped silica fiber lasers by polycrystalline Cr2+:ZnSe microchips

We demonstrate passive Q-switching of short-length double-clad Tm3+-doped silica fiber lasers near 2 mu m pumped by a laser diode array (LDA) at 790 nm. Polycrystalline Cr2+:ZnSe microchips with thickness from 0.3 to 1 mm are adopted as the Q-switching elements. Pulse duration of 120 ns, pulse energy over 14 mu] and repetition rate of 53 kHz are obtained from a 5-cm long fiber laser. As high as 530 kHz repetition rate is achieved from a 50-cm long fiber laser at similar to 10-W pump power. The performance of the Q-switched fiber lasers as a function of fiber length is also analyzed. (c) 2008 Elsevier B.V. All rights reserved.

Tm-doped fibre laser pumped Cr2+: ZnSe poly-crystal laser

Demonstrations of cw lasing in Cr2+:ZnSe poly-crystal are reported. The laser consists of a 1.7-mm-thick Cr2+:ZnSe poly-crystal disc pumped by a Tm-silica double-clad fibre laser at 2050nm. Using a concave high-reflection mirror with a radius of curvature of 500mm as the rear mirror, the laser delivers up to 1030mW of radiation around 2.367 mu m.

970nm抽运下Tm^3／Yb^3＋共掺氧氟玻璃的频率上转换发光

稀土离子掺杂的氧氟玻璃是一种新型上转换发光材料。制备了Tm^3／Yb^3＋单掺、共掺的摩尔分数为n（SiO2）-0．30，n（PbF2）-0．50，n=（Al2O3）=0．15，n（AlF3）=（0．049-x），n（TmF3）=y，n（YbF3）=x（x=0，0．001，0．010，0．015，0．020，y=0，0．001）系统氧氟玻璃，研究了其上转换发光特性、分析了其上转换发光机理。研究发现，在970nm抽运光源激发下，Tm^3＋单掺时没有可见光上转换发射；而加入Yb^3＋后产生了强的蓝光（452n

卤化铅调整Tm^3＋／Yb^3＋共掺碲酸盐玻璃上转换发光研究

研究了卤化铅调整Tm^3+／Yb^3+共掺碲酸盐玻璃的热稳定性能、Raman光谱和上转换发光光谱，分析了Tm^3+／Yb^3+共掺氧卤碲酸盐玻璃的上转换发光机理．结果发现：混合卤化铅调整Tm^3+／Yb^3+共掺碲酸盐玻璃具有好的热稳定性能、低的声子能量、强的上转换蓝光．这表明混合卤化铅调整Tm^3+／Yb^3+共掺碲酸盐玻璃是一种上转换蓝光激光器的潜在基质材料．

Yb^3＋敏化Tm^3＋掺杂氧卤碲酸盐玻璃的上转换发光研究

研究了Yb2O3浓度对Tm^3＋／Yb^3＋共掺氧卤碲酸盐玻璃的上转换发光的影响，分析了上转换发光机理。结果发现，通过980nm的激光二极管激发，在室温下同时观察到强烈的蓝光（475nm）和微弱的红光（649nm），分别是由于Tm^3＋离子^1G4→^3H6和^1G4→^3F4跃迁产生的；上转换机理分析表明，上转换蓝光和红光都是由于双光子吸收过程。随Yb2O3浓度增加，Yb^3＋离子寿命降低，Yb^3＋到Tm^3＋的能量转移效率增加，上转换蓝光和红光强度先增加，在Yb2O3摩尔比为3时达到最大，然后降低。