三种海水经济鱼类早期发育生物学的研究

海水经济鱼类的养殖在我国已经形成第四次海水养殖浪潮，经济效益显著，有力地推动了我国海水养殖的产业结构调整和可持续发展。然而在海水养殖发展过程中也存在着诸多问题，尤其是早期发育阶段的高死亡率，严重制约了我国海水养殖产业的稳定和健康发展。 海水鱼类养殖的关键为高质量，高存活率苗种的生产和培育，由于鱼类种类繁多，生物多样性丰富，对应实际的繁育技术，尤其是新品种的开发，必须要做出相应的调整。这就要求我们必须对每一种鱼类早期发育有所了解，并将形态和组织上的数据用于指导生产。 本文通过显微观察和组织学研究，主要描述和研究了我国北方三种重要的海水经济鱼类(条斑星鲽、杂交鲆、条石鲷)的早期发育生物学，并结合实际生产进一步阐明关键期的产生原因，机理以及采用相应的对策。具体结果如下： 1.条斑星鲽：作为冷温性鲆鲽鱼类，条斑星鲽早期发育过程的特征主要有： ① 条斑星鲽受精卵无油球，卵子呈半浮性；不同步卵裂现象提前，发生在第三次卵裂；卵裂期裂球大小差异大。孵化过程较长，在水温8 ± 0.3℃，盐度33的条件下，经9 d孵化。条斑星鲽胚胎发育的不同时期对温度的敏感性不同，其中原肠期对温度比较敏感。 ②在8-10℃，盐度33的条件下，8-9 dph开口摄食。且开口时，其吻前端出现有一点状黑褐色素，构成了条斑星鲽仔鱼“开口期”的重要标志。卵黄囊于消失。在后期仔鱼末期，背鳍和臀鳍上形成特有的黑褐色条斑带。 ③杯状细胞首先出现在咽腔后部和食道前段，胃腺和幽门盲囊出现于29 dph，变态期始于30dph。在条斑星鲽早期发育过程中，观察到其直肠粘膜层细胞质出现大量嗜伊红颗粒，为仔鱼肠道上皮吸收的蛋白质。 ④首先淋巴化的免疫器官是头肾，然后是胸腺和脾脏，这与大部分硬骨鱼类不同。条斑星鲽除头肾和脾脏外，胸腺实质也形成MMCs。其中以脾脏形成MMCs最为丰富，形态多样。 2. 杂交鲆：为同属的牙鲆和夏鲆间的远缘杂交种，其发育过程的特点为： ① 在温度为15.4～16.0℃，杂交鲆胚胎从受精到孵化所需的时间为76 h左右，胚孔关闭前期，胚胎先出现视囊及克氏囊，而后形成体节。孵出前胚体在卵膜内环绕不到1周。 ② 孵化后消失。杂交鲆群体变态间隔长(34-60 dph)，且变态高峰期出现的冠状幼鳍不明显(与母本牙鲆相比)，数量为7-8根。 ③组织学观察发现，其消化系统中胃腺出现较晚，且胃腺发育过程缓慢(与母本牙鲆相比)。甲状腺滤泡增生不明显，颜色较浅，数量较少。杂交鲆在早期发育过程中，并没有出现鳔原基。 3. 条石鲷作为岩礁性的暖水性鱼类，早期发育过程也较为特殊，包括外形以及内部的器官结构。主要特点有： ① 受精卵：受精卵卵黄上具有龟裂结构，为鱼卵的分类特征之一。 ② 初孵仔鱼：初孵仔鱼背鳍膜上的黑色素，从体背面向背鳍膜边缘移动，到3dph仔鱼基本消失，此为本种仔鱼发育所特有的特点。 ③ 后期仔鱼和稚鱼：肠道肌肉层加厚明显，仔稚鱼胃肠排空率急剧上升，死亡率增加，通过改善常规的投饵方式部分解决了这个死亡高峰的问题。在幼鱼初期，牙齿融合为骨喙，为石鲷科鱼类的特征。 ④胸腺上皮分泌细胞：类似的现象同样在虹鳟鱼中发现，但是虹鳟鱼胸腺上皮分泌细胞不如条石鲷的丰富，同样也不如条石鲷的排列整齐，而是零星分布在胸腺上皮与咽腔接触的表面。除了正常的造血器官—脾脏和头肾外，肝脏、胰腺和鳔等多种组织等也出现MMCs，此现象在硬骨鱼类不多见，一般发生在软骨鱼类。

Density-dependent effects on seston dynamics and rates of filtering and biodeposition of the suspension-cultured scallop Chlamys farreri in a eutrophic bay (northern China): An experimental study in semi-in situ flow-through systems

Effects of stocking density on seston dynamics and filtering and biodeposition by the suspension-cultured Zhikong scallop Chlamys farreri Jones et Preston in a eutrophic bay (Sishili Bay, northern China), were determined in a 3-month semi-field experiment with continuous flow-through seawater from the bay. Results showed that the presence of the scallops could strongly decrease seston and chlorophyll a concentrations in the water column. Moreover, in a limited water column, increasing scallop density could cause seston depletion due to scallop's filtering and biodeposition process, and impair scallop growth. Both filtration rate and biodeposition rate of C. farreri showed significant negative correlation with their density and positive relationship with seston concentration. Calculation predicts that the daily removal of suspended matter from water column by the scallops in Sishili Bay ecosystem can be as high as 45% of the total suspended matter; and the daily production of biodeposits by the scallops in early summer in farming zone may amount to 7.78 g m(-2), with daily C, N and P biodeposition rates of 3.06 x 10(-1), 3.86 x 10(-2) and 9.80 x 10(-3) g m(-2), respectively. The filtering and biodeposition by suspension-cultured scallops could substantially enhance the deposition of total suspended particulate material, suppress accumulation of particulate organic matter in water column, and increase the flux of C, N and P to benthos, strongly enhancing pelagic-benthic coupling. It was suggested that the filtering-biodeposition process by intensively suspension-cultured bivalve filter-feeders could exert strong top-down control on phytoplankton biomass and other suspended particulate material in coastal ecosystems. This study also indicated that commercially suspension-cultured bivalves may simultaneously and potentially aid in mitigating eutrophication pressures on coastal ecosystems subject to anthropogenic N and P loadings, serving as a eutrophic-environment bioremediator. The ecological services (e.g. filtering capacity, top-down control, and benthic-pelagic coupling) functioned by extractive bivalve aquaculture should be emphasized in coastal ecosystems. (c) 2005 Elsevier B.V. All rights reserved.

Flame Propagation of H_2-Air in a Semi-Open Obstructed Tube

针对氢／空气混合物,通过实验研究了其预混火焰在半开口管道中的火焰传播加速现象,结果表明,火焰传播状态随着氢气当量比的变化而发生改变。当氢／空气混合物被点燃后,由于障碍物的扰动,火焰在管道中不断加速传播,并最终到达一准稳态传播。在氢气当量比0.31附近时,火焰速度发生跃变。当氢气当量比足够大时,火焰传播由爆燃态转变为爆轰态。在本实验条件下,爆燃转准爆轰的临界条件是d/Lambda>=2.6（d是圆环形障碍物内径,人是爆轰格胞尺度）。障碍物阻塞比的变化对最大火焰速度和压力提升的影响不明显。

A Semi-Empirical Equation of Penetration Depth on Concrete Target Impacted by Ogive-Nose Projectiles

In this paper, the penetration process of ogive-nose projectiles into the semi-infinite concrete target is investigated by the dimensional analysis method and FEM simulation. With the dimensional analysis, main non-dimensional parameters which control the penetration depth are obtained with some reasonable hypothesis. Then, a new semi-empirical equation is present based on the original work of Forrestal et al., has only two non-dimensional combined variables with definite physical meanings. To verify this equation, prediction results are compared with experiments in a wide variation region of velocity. Then, a commercial FEM code, LS-DYNA, is used to simulate the complex penetration process, that also show the novel semi-empirical equation is reasonable for determining the penetration depth in a concrete target.

Semi-weight function method on computation of stress intensity factors in dissimilar materials

Semi-weight function method is developed to solve the plane problem of two bonded dissimilar materials containing a crack along the bond. From equilibrium equation, stress and strain relationship, conditions of continuity across interface and free crack surface, the stress and displacement fields were obtained. The eigenvalue of these fields is lambda. Semi-weight functions were obtained as virtual displacement and stress fields with eigenvalue-lambda. Integral expression of fracture parameters, K-I and K-II, were obtained from reciprocal work theorem with semi-weight functions and approximate displacement and stress values on any integral path around crack tip. The calculation results of applications show that the semi-weight function method is a simple, convenient and high precision calculation method.

Semi-gas kinetics model for performance modeling of flowing chemical oxygen-iodine lasers (COIL)

A semi-gas kinetics (SGK) model for performance analyses of flowing chemical oxygen-iodine laser (COIL) is presented. In this model, the oxygen-iodine reaction gas flow is treated as a continuous medium, and the effect of thermal motions of particles of different laser energy levels on the performances of the COIL is included and the velocity distribution function equations are solved by using the double-parameter perturbational method. For a premixed flow, effects of different chemical reaction systems, different gain saturation models and temperature, pressure, yield of excited oxygen, iodine concentration and frequency-shift on the performances of the COIL are computed, and the calculated output power agrees well with the experimental data. The results indicate that the power extraction of the SGK model considering 21 reactions is close to those when only the reversible pumping reaction is considered, while different gain saturation models and adjustable parameters greatly affect the output power, the optimal threshold gain range, and the length of power extraction.

Elastodynamic stress intensity factor history for a semi-infinite crack under three-dimensional transient loading

The dynamic stress intensity factor history for a semi-infinite crack in an otherwise unbounded elastic body is analyzed. The crack is subjected to a pair of suddenly-applied point loadings on its faces at a distance L away from the crack tip. The exact expression for the mode I stress intensity factor as a function of time is obtained. The method of solution is based on the direct application of integral transforms, the Wiener-Hopf technique and the Cagniard-de Hoop method. Due to the existence of the characteristic length in loading this problem was long believed a knotty problem. Some features of the solutions are discussed and graphical result for numerical computation is presented.

Compressible laminar boundary-layer flows of a dusty gas over a semi-infinite flat-plate

The compressible laminar boundary-layer flows of a dilute gas-particle mixture over a semi-infinite flat plate are investigated analytically. The governing equations are presented in a general form where more reasonable relations for the two-phase interaction and the gas viscosity are included. The detailed flow structures of the gas and particle phases are given in three distinct regions : the large-slip region near the leading edge, the moderate-slip region and the small-slip region far downstream. The asymptotic solutions for the two limiting regions are obtained by using a seriesexpansion method. The finite-difference solutions along the whole length of the plate are obtained by using implicit four-point and six-point schemes. The results from these two methods are compared and very good agreement is achieved. The characteristic quantities of the boundary layer are calculated and the effects on the flow produced by the particles are discussed. It is found that in the case of laminar boundary-layer flows, the skin friction and wall heat-transfer are higher and the displacement thickness is lower than in the pure-gas case alone. The results indicate that the Stokes-interaction relation is reasonable qualitatively but not correct quantitatively and a relevant non-Stokes relation of the interaction between the two phases should be specified when the particle Reynolds number is higher than unity.

The Characteristics of Semi-Cokes --The Solid Residues from Coal Partial Gasification

In this paper the proximate analysis and ultimate analysis of sulfur in different semi-cokes generated from Rizhao bituminous coal and Beijing anthracite under different temperatures is done. Also the tendency of the contents of volatile, ash, fixed carbon and sulfur in different semi-cokes along with the different preparation temperatures is studied. Then the combustion experiment of semi-cokes in the drop-tube furnace system was carried out, and the kinetic parameters of different semi-cokes ware calculated.

A Semi-Empirical Equation of Penetration Depth on Concrete Target Impacted by Ogive-Nose Projectiles

In this paper, the penetration process of ogive-nose projectiles into the semi-infinite concrete target is investigated by the dimensional analysis method and FEM simulation. With the dimensional analysis, main non-dimensional parameters which control the penetration depth are obtained with some reasonable hypothesis. Then, a new semi-empirical equation is present based on the original work of Forrestal et al., has only two non-dimensional combined variables with definite physical meanings. To verify this equation, prediction results are compared with experiments in a wide variation region of velocity. Then, a commercial FEM code, LS-DYNA, is used to simulate the complex penetration process, that also show the novel semi-empirical equation is reasonable for determining the penetration depth in a concrete target.

Broad-bandwidth semi-noncollinear optical parametric amplification in periodically poled LiNbO3 based on tilted quasi-phase-matched gratings

On the basis of noncollinear optical parametric amplification in periodically poled lithium niobate (PPLN) which is realized by quasi-phase matching (QPM) technology, we consider the possibility of semi-noncollinear phase matching between collinear and noncollinear geometries by tilting a PPLN-crystal's parallel grating at a sure angle. Numerical simulation with proper parameters shows that we can achieve a broader optical parametric amplification (OPA) bandwidth than that of noncollinear geometry. About 121 nm at a signal wavelength of 800 and 70 nm at a signal wavelength of 1064 nm under optimal conditions are obtained when the crystal length is 9 mm.

Polaron effects on the optical absorptions in asymmetrical semi-parabolic quantum wells

The linear and nonlinear optical absorptions considering the weak-coupling electron-LO-phonon interaction in asymmetrical semiparabolic quantum wells are theoretically investigated. The numerical results for the typical GaAs/AlxGa1-xAs material show that the factors of Al content x, the relaxation time and the photon energy have great influence on the optical absorption coefficients. Moreover, the theoretical values of the optical absorptions are more than a factor of 2-3 higher than the one in the structure without considering the electron-LO-phonon interaction by calculating. (C) 2007 Elsevier B.V. All rights reserved.