Enlarged area A-type zeolite membranes prepared by vacuum seeding method

High quality A-type zeolite membranes, with enlarged area over 70 cm(2), were successfully synthesized on a tubular alpha-Al2O3 support by applying the vacuum seeding method.

Synthesis and properties of A-type zeolite membranes by secondary growth method with vacuum seeding

A-type zeolite membranes were successfully synthesized on tubular alpha-Al2O3 supports by secondary growth method with vacuum seeding In the seeding process, a thin, uniform and continuous seeding layer was closely attached to the support surface by the pressure difference between the two sides of the support wall. The effects of seed particle size, suspension concentration, coating pressure difference and coating time on the membrane and its pervaporation properties were investigated. The as-synthesized membranes were characterized by XRD and SEM. The quality of the membranes was evaluated by the pervaporation dehydration of 95 wt. % isopropanol/water mixture at 343 K. High quality A-type zeolite membranes can be reproducibly prepared by the secondary growth method with vacuum seeding under the conditions: seed particle size of 500-1200 nm, suspension concentration of 4-8 g/l, coating pressure difference of 0.0100-0.0250 MPa and coating time of 45-180 s. (C) 2004 Elsevier B.V. All rights reserved.

Preparation of novel silver-gold bimetallic nanostructures by seeding with silver nanoplates and application in surface-enhanced Raman scattering

Novel silver-gold bimetallic nanostructures were prepared by seeding with silver nanoplates in the absence of any surfactants. During the synthesis process, it was found that the frameworks of silver nanoplates were normally kept though the basal plane of silver nanoplates became rugged. The real morphology of these nanostructures depended on the molar ratio of gold ions to the seed particles. When the molar ratio of gold ions to silver atoms increased from 0.5 to 4, porous or branched silver-gold bimetallic nanostructures could be made. The growth mechanism was qualitatively discussed based on template-engaged replacement reactions and seed-mediated deposition reactions. Due to the unusual structures, they exhibited interesting optical properties. Moreover, they were shown to be an active substrate for surface-enhanced Raman scattering measurements.

Fabrication of Au(111) single-crystal nanoisland-arrayed electrode ensembles by template-directed seeding growth

A new and simple approach for preparation of Au(111) single-crystal nanoisland - arrayed electrode ensembles, based on fine colloidal Au monolayer-directed seeding growth, is reported.

Improved size control of large palladium nanoparticles by a seeding growth method

A new approach to the preparation of large palladium nanoparticles with diameters between 25 and 100 nm is presented. In this approach PdCl42- ions are reduced on the surface of performed 12-nm-diameter gold "seeds'' by the introduction of ascorbic acid. The resultant particles exhibit improved monodispersity relative to previous work. Interestingly, these nanoparticles possess Au-Pd core-shell structures. The method can be scaled up to produce 50-110 mg of large palladium nanoparticles.

Seeding nets with neutral spores of the red alga Porphyra umbilicalis (L.) Kutzing for use in integrated multi-trophic aquaculture (IMTA)

Nets in traditional Porphyra mariculture are seeded with conchospores derived from the conchocelis phase, and spend a nursery period in culture tanks or calm coastal waters until they reach several centimeters in length. Some species of Porphyra can regenerate the foliose phase directly through asexual reproduction, which suggests that the time, infrastructure, and costs associated with conchocelis culture might be avoided by seeding nets with asexual spores. Here, we present work from a short-term mariculture study using nets seeded with asexual spores (neutral spores) of a native Maine species of Porphyra. Porphyra umbilicalis (L.) Kutzing was selected for this proof of concept research because of its reproductive biology, abundance across seasons in Maine, and evidence of its promise as a mariculture crop. We studied the maturation, release, and germination of the neutral spores to develop an appropriate seeding protocol for nets, followed by development of a nursery raceway to provide an easily manipulated environment for the seeded nets. Neutral spores were produced throughout the year on the central Maine coast,however, there was a temporal variability in the number and survival of released neutral spores, depending upon thallus position in the intertidal zone. Small thalli were strictly vegetative, but most thalli reproduced by neutral spores- sexual reproduction was absent. Neutral spores germinated quickly at 10 and 15 'C, but germination was delayed at 5 degrees C. Unlike some algal zygotes and spores, neutral spores of R umbilicalis required light to germinate; however, irradiances of 25 and 100 mu mol photons M-2 S-1 were equally sufficient for germination. Rafts of seeded nets were deployed in Cobscook Bay, Maine, at two distances from salmon aquaculture pens and at a control site on a nearby, fallow aquaculture site (no salmon). There was no difference in nitrogen content of harvested thalli; however, both the density and the surface area of harvested thalli were different among the sites. The possible causes of these differences are discussed in the context of potential use of P umbilicalis in IMTA. (C) 2007 Elsevier B.V. All rights reserved.

The near wall velocity measurements in microchannels with different diameter particles by microPIV/PTV. 8th International symposium on PIV

In near wall measurements with microPIV/PTV, whether seeding particles can be effectively used to detect local fluid velocity is a crucial problem. This talk presents our recent measurements in microchannels [1][2]. Based on measured velocity profiles with 200nm and 50nm in pure water, we found that the measured velocity profiles are agreed with the theoretical values in the middle of channel, but large deviations between measured data and theoretical prediction appear close to wall (0.25mm

Synthesis and formation mechanism of silver nanowires by a templateless and seedless method

Silver nanowires in large quantities can be obtained through a simple method in the absence of a surfactant or polymer and without addition of external seeding nanocrystallites. A plausible mechanism was proposed to elucidate the formation mechanism of silver nanowires based on TEM studies.

光谱稳定性对直接探测多普勒测风激光雷达的影响研究

The wind error of the double-edge technique Doppler lidar due to the instability of injection-seeding solid laser and the drift of interferometer s spectrum was analyzed. Corresponding numerical simulation indicated that if the wind error of 1 m/s was achieved, the unsuccessful injection-seeding pulses should be less than 0.06% in integration time of 5 min. (30000 pulses). In the respect of spectrum drift of the interferometer, double temperature control systems were used and the accuracy of minus or plus 0.002°C was obtained, corresponding to the wind error of minus or plus 0.226 m/s. Monitoring of buildup time of the injection-seeding laser and temperature of the interferometer was significantly to improve the invertion accuracy of wind error by rejecting the data with frequency jumping and drifting. Researches of injection-seeding and spectrum stability of the interferometer were practical for the development of double-edge wind lidar.}

All solid-state, injection-seeded Ti:sapphire ring laser

In this letter, we present an all solid-state, injection-seeded Ti:sapphire laser. The laser is pumped by a laser diode pumped frequency-doubled Nd:YAG laser, and injection-seeded by an external cavity laser diode with the wavelength between 770 and 780 nm. The single longitude mode and the doubling efficiency of the laser are obtained after injection seeding. The experimental setup and relative results are reported. It is a good candidate laser source for mobile differential absorption lidar (DIAL) system.

毛乌素沙地油蒿与籽蒿种子萌发对光照的反应

油蒿(Artemisia ordosica)与籽蒿(Artemisia sphaerocephala)为毛乌素沙地的优势物种，广泛用于我国北方干旱、半干旱区的生态恢复。油蒿与籽蒿种子萌发对温度、水分等环境条件的反应已有较为明确的研究结果，但关于这两种蒿属植物种子萌发对光照反应的研究目前存在两种不同的结论，对飞播技术的改善造成一定影响。 影响油蒿与籽蒿种子萌发对光照反应的因素较多。如种源地、结实部位、种子颜色、种子保存方式与时间、实验条件、温度等。考虑种源地、种子保存时间与方式、结实部位及温度，从多方面系统研究油蒿与籽蒿种子萌发对光照的反应。结果表明当温度较低时(10:20C)，萌发率和萌发速率在黑暗条件下显著高于在光照条件下。采自榆林地区的种子萌发状况相对较差，萌发率和萌发速率在大多数情况下显著低于其他两地;各种源地上下部种子萌发率有一定差异，大多数结实部位为上部的种子最终萌发率和萌发速率高于下部的种子;保存几周的种子萌发率变化不大，但在温度较高和较低时，随着种子保存时间的延长，萌发率下降较快，而在适宜温度下种子萌发率变化不明显;种子保存方式的不同造成种子萌发情况的差异，但差异不明显;黑暗条件下比近似黑暗条件下的种子萌发率略低。上述因素对种子萌发均具有一定影响，但总体特征是种子萌发对光照的反应表现为强光抑制种子的萌发，黑暗促进种子萌发。当温度较高时(15:25C)，光照与黑暗条件下种子萌发率差异不大，但黑暗条件下种子的萌发速率显著高于光照条件下;当其它条件相同时，种子萌发率和萌发速率显著高于温度较低时(10:20C)。因而，适宜的温度和黑暗条件有利于油蒿与籽蒿种子的萌发。在飞播实践时应为种子创造一定的沙埋条件，创造有利于种子萌发的黑暗环境，促进种子的萌发，提高飞播工作的成效。

毛乌素沙地四种关键植物幼苗出土及生长对沙埋和水分的响应

飞播是毛乌素沙地植被恢复与重建的重要手段。但此项技术仍存在一些问题，如飞播后成苗率较低等。柠条(Caragana korshinskii)、羊柴(Hedysarum laeve)、籽蒿(Artimisia sphaerocephala)与油蒿(Artimisia ordosica)是毛乌素沙地广泛分布的物种，也是飞播的主要物种。本文以飞播植被恢复技术为突破口，研究沙埋和土壤水分对种子萌发，幼苗出土和生长的影响，探讨幼苗出土和生长对沙生环境的适应对策。对采用合适的物种进行生态工程建设，提高生态工程的稳定性及可持续性具有重要意义。同时，本项研究有助于加深半干旱区植物对沙生环境适应机理的认识。 以上述4种植物为研究对象，设定7个沙埋深度和9个水分梯度，研究种子萌发和幼苗出土对沙埋和单次供水的响应。设定7个沙埋深度，选择3个沙丘部位，研究沙丘不同部位对植物种子萌发的影响。设定6个沙埋深度、4个水分梯度，研究两种蒿属植物幼苗生长对不同沙埋和供水的响应。得出如下主要结论： (1) 对于种子质量相对较大的柠条和羊柴而言，在一次性10-20 mm供水量条件下，幼苗主要在0.5-2 cm埋藏深度之间出土，但在埋藏深度为5 cm时这两个物种仍有少部分幼苗能够出土;对于种子质量相对较轻的油蒿和籽蒿而言，在一次性10-20 mm供水量时，幼苗主要在0.5 cm埋藏深度出土，油蒿和籽蒿幼苗在埋藏深度为1.5和2 cm时不能出苗。沙埋深度为0.5 cm时，4个物种出苗率较高、出苗时间较短、出苗速率较快。 (2) 实验期内(30天)在一次性供水量分别为5、7.5和7.5mm时，柠条、羊柴和油蒿出土幼苗全部死亡;在一次性供水量高于15-20 mm时，出土幼苗死亡率低于50%;籽蒿在供水量高于10 mm时出土幼苗死亡率低于50%;随供水量的增加4个物种出土幼苗的死亡率降低。 (3) 结合毛乌素沙地降雨特点与本文实验结果，0.5 cm的沙埋及7.5 mm以上的单次降雨量是上述4种植物自然条件下出苗较高的重要条件。 (4) 在沙丘顶部，2-7 cm沙埋深度之内各个物种不同沙埋深度的种子萌发率差异不显著。沙丘背风坡中部和底部，4个物种在沙埋深度为1 cm时的种子萌发率均显著高于5、7 cm时的萌发率。当沙埋深度为1-5 cm时，柠条和羊柴种子在坡面不同位置的萌发率均高于20%，且显著高于7 cm沙埋深度时的萌发率。在背风坡底部时，柠条、羊柴、油蒿和籽蒿的种子萌发率达到最大值，分别为45.2±3.27%、48.4±5.21%、20.8±4.63%和22.4±4.83%。4个物种的种子萌发率从沙丘顶部到背风坡中部到底部呈递增趋势，表明背风坡中部和底部的环境条件要比顶部更适合种子萌 发。 (5) 部分沙埋促进幼苗生长。2种蒿属植物幼苗在沙埋深度为0.25、0.5 H时比在0、0.75 H时具有更高的生物量、叶面积、相对生长速率（RGR）和净同化速率（NAR）。在75 mm/月供水量时，油蒿幼苗具有较高的生物量和叶面积，但当供水量达到100 mm/月时其幼苗生长受到抑制。油蒿幼苗在遭遇较深（0.5、0.75 H）沙埋时的根冠比要显著高于未沙埋幼苗的根冠比;籽蒿幼苗根冠比在不同沙埋条件下没有显著变化。籽蒿幼苗在50 mm供水量时具有较高的RGR。油蒿幼苗在75 mm供水量时具有较高的RGR和NAR。

Regulation of gamete release in the economic brown seaweed Hizikia fusiforme (Phaeophyta)

Gamete release is an essential event in artificial seeding of the economic brown seaweed, Hizikia fusiforme. Mass egg release occurred in the dark, with few eggs being discharged in the light. Release of eggs was elicited with eight practical salinity units (one PSU = 1 g sea salts l(-1)) and was inhibited by salinity levels > 32 PSU. Egg release was optimal at 23 degrees C, and was decreased by 72% in agitated seawater compared to unstirred seawater. Inhibitors of photosynthesis and ions channels suppressed egg release, indicating that this process was physiologically associated with photosynthetic activity and ion transport.

Effects of different modified underlayer surfaces on growth and optical properties of InGaN quantum dots

InGaN/GaN quantum dots were grown on the sapphire (0 0 0 1) substrate in a metalorganic chemical vapor deposition system. The morphologies of QDs deposited on different modified underlayer (GaN) surfaces, including naturally as grown, Ga-mediated, In-mediated, and air-passivated ones, were investigated by atomic force microscopy (AFM). Photo luminescence (PL) method is used to evaluate optical properties. It is shown that InGaN QDs can form directly on the natural GaN layer. However, both the size and distribution show obvious inhomogeneities. Such a heavy fluctuation in size leads to double peaks for QDs with short growth time, and broad peaks for QDs with long growth time in their low-temperature PL spectra. QDs grown on the Ga-mediated GaN underlayer tends to coalesce. Distinct transform takes place from 3D to 2D growth on the In-mediated ones, and thus the formation of QDs is prohibited. Those results clarify Ga and In's surfactant behavior. When the GaN underlayer is passivated in the air, and together with an additional low-temperature-grown seeding layer, however, the island growth mode is enhanced. Subsequently, grown InGaN QDs are characterized by a relatively high density and an improved Gaussian-like distribution in size. Short surface diffusion length at low growth temperature accounts for that result. It is concluded that reduced temperature favors QD's 3D growth and surface passivation can provide another promising way to obtain high-density QDs that especially suits MOCVD system. (c) 2004 Elsevier Ltd. All rights reserved.

Crystallographic tilt in GaN layers grown by epitaxial lateral overgrowth

The crystallographic tilt in GaN layers grown by epitaxial lateral overgrowth (ELO) on sapphire (0001) substrates was investigated by using double crystal X-ray diffraction (DC-XRD). It was found that ELO GaN stripes bent towards the SiNx mask in the direction perpendicular to seeding lines. Each side of GaN (0002) peak in DC-XRD rocking curves was a broad peak related with the crystallographic tilt. This broad peak split into two peaks (denoted as A and B), and peak B disappeared gradually when the mask began to be removed by selective etching. Only narrow peak A remained when the SiNx mask was removed completely. A model based on these results has been developed to show that there are two factors responsible for the crystallographic tilt: One is the non-uniformity elastic deformation caused by the interphase force between the ELO GaN layer and the SiNx mask. The other is the plastic deformation, which is attributed to the change of the threading dislocations (TDs)-from vertical in the window regions to the lateral in the regions over the mask.