Materials selection in mechanical design for microsensors and microactuators

Microsensors and microactuators are vital organs of microelectromechanical systems (MEMS), forming the interfaces between controller and environment. They are usually used for devices ranging in size at sub-millimeter or micrometer level, transforming energy between two or more domains. Presently, most of the materials used in MEMS devices belong to the silicon material system, which is the basis of the integrated circuit industry. However, new techniques are being explored and developed, and the opportunities for MEMS materials selection are getting broader. The present paper tries to apply 'performance index' to select the material best suited to a given application, in the early stage of MEMS design. The selection is based on matching performance characteristics to the requirements. A series of performance indices are given to allow a wide range comparison of materials for several typical sensing and actuating structures, and a rapid identification of candidates for a given task. (C) 2002 Elsevier Science Ltd. All rights reserved.

Narrow stripe selective growth of InGaAlAs waveguides used for buried heterostructure lasers - art. no. 63210I

The narrow stripe selective growth of the InGaAlAs bulk waveguides and InGaAlAs MQW waveguides was first investigated. Flat and clear interfaces were obtained for the selectively grown InGaAlAs waveguides under optimized growth conditions. These selectively grown InGaAlAs waveguides were covered by specific InP layers, which can keep the waveguides from being oxidized during the fabrication of devices. PL peak wavelength shifts of 70 nm for the InGaAlAs bulk waveguides and 73 nm for the InGaAlAs MQW waveguides were obtained with a small mask stripe width varying from 0 to 40 gm, and were interpreted in considering both the migration effect from the masked region (MMR) and the lateral vapor diffusion effect (LVD). The quality of the selectively grown InGaAlAs MQW waveguides was confirmed by the PL peak intensity and the PL FWHM. Using the narrow stripe selectively grown InGaAlAs MQW waveguides, then the buried heterostructure (BH) lasers were fabricated by a developed unselective regrowth method, instead of conventional selective regrowth. The InGaAlAs MQW BH lasers exhibit good performance characteristics, with a high internal differential quantum efficiency of about 85% and an internal loss of 6.7 cm(-1).

自养氨氧化混合种群特性和共存机理初步研究

组特殊自养氨氧化混合种群，表现：无机环境种群生长迅速、生物量高；在一个完全无机的自养生长环境中，不仅保持高氨氧化速率，并出现丰富的异养微生物种群；该种群置于异养、厌氧环境中，迅速表现出产氢特征。对于这样一个特殊的生态体系，研究其共生机理，以及联接这些种群之间的碳源和能源问题，将具有非常重要意义。我们拟从种群特征、细胞表面分泌产物、游离体系产物多糖、蛋白和脂肪酸方面开展研究。 第一部分，自养氨氧化混合种群的基本特征。采用氨氧化培养基，进行种群氨氧化特征研究；采用扫描电镜观察自养混合种群的微观特征；沉降、离心去除微生物种群，分析水相中的总有机碳、糖类等物质；利用LB培养基进行种群的分离、纯化，并采用DGGE手段对微生物种群结构进行分析。结果表明，接入菌种后（2/5000（V/V）），培养液中氨（200mg/L）在3－5天内快速降解；亚硝酸盐与氨氮变化呈负相关趋势，仅有少量硝酸盐含量（< 30mg/L）。氨氧化种群的生物量增长与氨氧化趋势一致，初始生物量7.75 mg/L(蛋白含量)，3-5天后生物量快速增长，并达到最高63.06 mg/L（蛋白含量）。电镜图片显示，种群外包裹一层粘液。离心除去菌体后，检测培养液总有机碳和糖的含量，同样表现出与生物量增长相似的特征，分别由初始的3.73、2.35 mg/L，3－5内天迅速增加，并分别达到最大值35.19、27.45 mg/L。经初步分离、纯化并对纯化菌株进行测序，获得了10株异养微生物分别为布鲁氏菌科苍白杆菌属、纤维单孢菌、类芽孢菌属、黄杆菌属、无色杆菌、鞘脂单胞菌、嗜麦芽寡养单胞菌、噬氢菌属、硫红球菌、假单胞菌；DGGE显示，约有20分条离带，我们对其中的两条优势条带进行切割回收测序，鉴定为欧洲亚硝化单胞菌（Nitrosomonas eur）。 第二部分：混合种群自养-异养菌共生的可能机制。在对微生物种群特征初步分析基础上，针对胞外糖类组分可能被微生物代谢分解，我们重点对微生物细胞蛋白质与糖类进行分析。采用超声结合RIPA裂解液裂解，SDS-PAGE电泳分析混合种群总蛋白种类，并通过氨基酸分析仪及红外光谱法分析氨基酸组成及蛋白红外特征。采用超声破碎结合反复冻融对细胞样品进行处理，提取液采用醇沉、Sevage脱氮白，凝胶过滤方法脱盐和分级分离。对提取物的糖分析包括：紫外扫描，红外光谱，核磁共振，单糖组成分析；扫描电镜观察菌群破裂现象。SDS-PAGE分析结果表明：氨氧化种群不同生长阶段都显示出42kD蛋白表达量很高，d4时42kD蛋白表达已经很强，4-7d内一直持续这种过量表达，直到d8后表达开始减弱。说明42kD蛋白可能与氨氧化密切相关。红外光谱分析显示：细胞提取物的特征峰分布在3427.42cm-1、1718.18 cm-1和1681.72 cm-1、1160.07和1086.74 cm-1，分别对应为OH、 C=O、C－O－C基团，表明具有蛋白的典型特征；氨基酸分析显示蛋白中的Gly,Asp,Ala,Glu含量相对较高。 提取物中胞外多糖分离谱图得到不均一组分，共得到6个收集峰；紫外扫描在201－213 nm处有多糖吸收峰，同样表明多糖成分不均一性；多糖红外光谱特征峰主要分别在3400.49 cm-1、2920.28 cm-1、1154.54和1087.52 cm-1，对应OH、－CH2－ or CH 、C－O－H or C－O－C等多糖特征基团；多糖提取物核磁共振1H d4.3～5.9之间出现强吸收峰，这是1H中，多糖存在的明显证据，1H NMR中，其中O-乙酰基的甲基上的氢信号为d1.1～1.3之间。糖肟全苯甲酸酯衍生物的HPLC测定中，得到单一的单糖峰，由于时间问题，还未进行更深入的试验；电镜图片显示，种群中的细胞有大量的破裂现象。 实验表明，自养氨氧化混合种群显示出快速的氨氧化速率，氨氧化过程生物量和有机质的增加明显。微生物种群包裹粘液层，并分离纯化出大量的异养菌；去除菌体后的游离培养液中存在有机质（包括多糖）说明无机自养生长体系中存在异养菌生长、繁殖的二次碳源；细胞提取物中蛋白条带数目多、种类丰富；细胞多糖提取物具有明显的多糖特征，以及单糖的存在。结合种群的显微特征和游离体系中的有机质的检测结果，我们认为，无机自养生长体系中，种群细胞生长过程中发生的破裂现象可能是导致大量的蛋白、多糖释放到游离胞外，并成为其他异养菌生长的碳源和氮源。这可能是自养体系中，大量异养菌共生的可能机制，至于是什么原因引起种群生长过程中产生的破裂现象，还有待下一步深入研究。 A group of mixed autotrophic ammonia oxidizing populations, having much biological characteristic tested by concerned personnel for pilot test: Performed rapid population growth and obtained high biomass in inorganic environment; Not only maintained a high rate of ammoxidation, promoted a wealth of heterotrophic microbial populations growth in a totally inorganic and autotrophic growth environment; Placed in heterotrophic and anaerobic environment,had the performance characteristics that could rapidly produce hydrogen.For such a special ecological system, Study its symbiotic mechanism and the connection between these populations of carbon and energy issues, will have a very important significance. We intended from the characteristics of the population, the secretion product of cell surface, free substance in the liquid medium like polysaccharide, protein and fatty acids carrying out research. Part I: The basic features of mixed autotrophic ammonia oxidizing populations . Use inorganic liquid medium, processed study for ammonia oxidation characteristics of the population; we used scanning electron microscopy to get micro-features of autotrophic ammonia oxidizing populations .The medium was carried out settlement and centrifugal then removed the microbial populations, after all of that we analysis the water phase for total organic carbon(TOC), carbohydrate and other substances; Solid ammonia oxidizing medium was adopted to separation and purification of population, DGGE means was for structure analysis of microbial population. The results showed that after the inoculum of bacteria (2 / 5000 (V / V)), ammonia in the culture medium (200 mg / L) was rapid degradation in 3-5 days; ammonia and nitrite have the negative correlation between changes in the trend, then only a small amount of nitrate content (<30mg / L). The biomass growth of ammoxidation population in line with the trend of ammonia oxidation, the initial volume of it was 7.75 mg / L (protein content), in 3-5 days upto 63.06 mg / L (protein content). Electron microscope image showed, the populations were wrapped in a layer of mucus, including the a large number ruptted micorbe , Centrifuge to remove bacteria, then detected the medium for total organic carbon and sugar content, result took on the same characteristics with biomass growth, that were from the initial 3.73、2.35 mg / L respectively, in 3-6 days achieved rapid increase in the maximum to 35.19、27.45 mg / L respectively. After initial separation、 purification ,then processed sequencing to strains purified and got the result that there were 10 heterotrophic microorganisms : Brucella Branch pale bacillus, Cellu lomonas, Bacillus species category, a Flavobacterium, colorless Bacteria, Aeromonas sheath fat, little support maltophilia Aeromonas, macrophages species hydrogen, sulphur-MI, Pseudomonas bacteria spores; DGGE display, there were 20 separation bands approximately. Part II: Mixed populations that autotrophic - heterotrophic bacteria symbiotic mechanism. On the basis of preliminary analysis of microbial population characteristics, aiming at extracellular carbohydrate components might be decomposition by microbial, we focused on microbial cell protein and carbohydrate analysis. Using ultrasound combined with RIPA lysis cracking the cells, SDS-PAGE electrophoresis analysis the total protein species of the population, and through the amino acid analyzer studied the compositions of amino acid and infrared spectroscopy analysis of a protein infrared characteristics. Using ultrasound combined with repeatedly freezing and thawing to treated the cell sample, then took the means that alcohol precipitation, deproteinization by Sevage, gel filtration aimed at desalination and grade separation to deal with the lysates . The extraction of sugar analysis included: UV scanning, IR, NMR, single-sugar composition analysis. SDS-PAGE analysis showed that: 42 kD protein expression was very high at different growth stages of mixed autotrophic ammonia oxidizing populations , on the fourth day, 42 kD protein expression had been very strong, 4-7d, it had continued this excessive expression, then started to weaken after 7 days. 42 kD protein that might be closely associated with ammonia oxidation. Infrared spectral analysis showed that: cell extracts with the characteristic that the peak distribution in 3427.42 cm-1、1718.18 cm-1 and 1681.72 cm-1、1160.07 cm-1 and 1086.74 cm-1 corresponding to OH、C = O、C-O-C Groups which had the typical characteristics of protein; and analysis showed that amino acids including Gly, Asp, Ala, Glu ,the content in the protein is relatively high. Exopolysaccharide in the extracts had the separation map that it was uneven, received a total of six collection peaks by the detection mode of phenol-sulphruic acid method ; ultraviolet scan in the 201-213 nm department had polysaccharide absorbing peak, the same ingredients that polysaccharide heterogeneity; infrared polysaccharide spectral characteristics of the main peak at 3400.49 cm-1, 2920.28 cm-1, 1154.54 and 1087.52 cm-1, corresponding OH,-CH2-or CH, C-O-H or C-O-C;and other characteristics of polysaccharide group; 1H NMR of polysaccharide extract appeared absorption peak between d4.3 ~5.9, which is the apparent evidence of polysaccharide, In 1H NMR, the hydrogen signal of one of O-acetyl was between 1.1 to 1.3. The determination of Sugar oxime whole benzoate derivatives by HPLC, there was a single-sugar peak, as a matter of time, yet more in-depth test. Summary: Mixed autotrophic ammonia oxidizing populations show us that it had the ability in ammonia oxidizing and it was great, organic matter and biomass increased significantly in the process of ammonia oxidation. Microbial populations was wrapped up slime layer, the phenomenon of cell breakdown obviously, and there were a lot of separation and purification of the heterotrophic bacteria; a lot of organic matter (including polysaccharides)remined in the medium that removal of cell indicated the inorganic system existed secondary carbon sources that could be used by the heterotrophic bacteria ; there were a large number proteins bands of cell extract, rich variety; cell extracts of polysaccharide had obvious characteristics of polysaccharide, and the existence evidence of single-sugar. Combined population of microscopic characteristics and free of organic matter in the test results, we believe that the health of inorganic system, population growth occurred in the course of the breakdown of the phenomenon is likely to lead to a lot of protein and polysaccharide released into the extracellular free, And other heterotrophic bacteria use them to the growth as carbon and nitrogen. This may be autotrophic system, the large number of heterotrophic bacteria symbiotic mechanism.

Flow-through room temperature phosphorescence optosensing for the determination of lead in sea water

The chelates formed between the heavy metal ion Pb(II) and the reagents 8-hydroxy-5-quinolinesulphonic acid, 8-hydroxy-7-quinolinesulphonic acid and 8-hydroxy-7-iodo-5-quinolinesulphonic acid exhibit strong room temperature phosphorescence (RTP) if retained on the surface of anion exchange resin beads. Based on the on-line formation, in a flow-injection system, of such RTP lead chelates and their transient immobilization on an anion exchange resin, three flow-through optosensing systems are investigated for lead in sea water. Optimum experimental conditions and the analytical performance characteristics of the three optosensors are discussed. Relative standard deviations (RSDs) of the order of 3% are typical at 100 ng ml−1 Pb(II) and the active sensing phases can easily be regenerated by passing 500 μl of 6 M hydrochloric acid. A lead(II) detection limit of 0.1 ng ml−1 (3×background SD, for 2 ml sample injection volumes) was achieved for the optosensor based on 8-hydroxy-7-quinolinesulphonic acid. Possible interferences present in sea water, including cations and anions which could affect the sensor response, are discussed in detail. Finally, the selected RTP flow-through optical sensor has been successfully tested for the determination of lead in sea water at a few ng ml−1.

n-channel, ambipolar, and p-channel organic heterojunction transistors fabricated with various film morphologies

The relationship between the performance characteristics of organic field-effect transistors (OFETs) with 2,5-bis(4-biphenylyl)-bithiophene/copper hexadecafluorophthalocyanine (BP2T/F16CuPc) heterojunctions and the thickness of the BP2T bottom layer is investigated. Three operating modes (n-channel, ambipolar, and p-channel) are obtained by varying the thickness of the organic semiconductor layer. The changes in operating mode are attributable to the morphology of the film and the hetero-junction effect, which also leads to an evolution of the field-effect mobility with increasing film thickness. In BP2T/F16CuPc heterojunctions the mobile charge carriers accumulate at both sides of the heterojunction interface, with an accumulation layer thickness of ca. 10 nm. High field-effect mobility values can be achieved in continuous and flat films that exhibit the heterojunction effect.

Electrochemical detector based on sol-gel-derived carbon composite material for capillary electrophoresis microchips

An on-chip disk electrode based on sol-gel-derived carbon composite material could be easily and reproducibly fabricated. Unlike other carbon-based electrodes reported previously, this detector is rigid, convenient to fabricate, and amenable to chemical modifications. Based on the stable and reproducible characters of this detector, a copper particle-modified detector was developed for the detection of carbohydrates which extends the application of the carbon-based electrode. In our experiments, the performance of the new integrated detector for rapid on-chip measurement of epinephrine and glucose was illustrated. Experimental procedures including the fabrication of this detector, the configuration of separation channel outlet and electrode verge, and the performance characteristics of this new electrochemical detector were investigated.

A STUDY ABOUT PH CHEMICALLY MODIFIED ELECTRODES BASED ON AMINO-DERIVATIVES OF NAPHTHALENE

The electrochemical polymerization of amino-derivatives of naphthalene has been studied on the platinum wire electrodes. The effects of acidity of the modifying media and the potential scan rate on the cyclic voltammograms are verified. As potentiometric pH sensors, the electrodes prepared from 1-naphthylamine and 2,3-diaminonaphthalene showed performance characteristics superior to some other electrodes tested. The electrode modified with 1-naphthylamine in the optimum medium showed a nearly Nernstian response of 4.20-13.70 pH and a slope of -54.8 mV/pH, while the linear range of the electrode prepared by 2,3-diaminonaphthalene was 4.00-13.60 pH, with a slope of -52.4 mV/pH.

A characteristics study on the performance of a 2-stage light gas gun

In order to obtain an overall and systematic understanding of the performance of a two-stage light gas gun (TLGG), a numerical code to simulate the process occurring in a gun shot is advanced based on the quasi-one-dimensional unsteady equations of motion with the real gas effect,;friction and heat transfer taken into account in a characteristic formulation for both driver and propellant gas. Comparisons of projectile velocities and projectile pressures along the barrel with experimental results from JET (Joint European Tons) and with computational data got by the Lagrangian method indicate that this code can provide results with good accuracy over a wide range of gun geometry and loading conditions.

Effects of anode temperature on working characteristics and performance of a low power arcjet thruster

An arc-heated thruster of 130–800 W input power is tested in a vacuum chamber at pressures lower than 20 Pa with argon or H2–N2 gas mixture as propellant. The time-dependent arc voltage-current curve, outside-surface temperature of the anode nozzle and the produced thrust of the firing arcjet thruster are measured in situ simultaneously, in order to analyze and evaluate the dependence of thruster working characteristics and output properties, such as specific impulse and thrust efficiency, on nozzle temperature.

Synthesis and surface characteristics of zirconia and modified zirconia: Performance of CO hydrogenation

ZrO2-A and ZrO2-B catalysts were prepared by two different coprecipitation methods and their performance of CO hydrogenation was studied. The results indicated that ZrO2 and Li-, Pd- and Mn-modified ZrO2 catalysts exhibited good selectivity and high STY to higher alcohols. The surface characteristics of ZrO2-A and ZrO2-B samples were investigated by means of BET, NH3-TPD, XRD and UV Raman technique. The tetragonal zirconia on the surface region of ZrO2-A and Li-Pd-Mn/ZrO2-A catalysts may be responsible for the high selectivity towards ethanol, while the monoclinic zirconia on the surface of ZrO2-B and Li-Pd-Mn/ZrO2-B catalysts may be crucial to the high isobutanol selectivity.

Correlation between the characteristics and catalytic performance of Ni-V-O catalysts in oxidative dehydrogenation of propane

Ni - V - O series catalysts for the oxidative dehydrogenation (ODH) of propane were prepared and characterized by BET, XRD, H-2- TPR, O-2-TPD-MS and electrical conductivity. At 425 degreesC a C3H6 selectivity of 49.9% was observed on Ni0.9V0.1OY at a C3H8 conversion of 19.4%, and the obtained selectivity is almost two times higher than that over NiO at the roughly same conversion of C3H8. The mobile oxygen species created by the interaction of NiO and V2O5 has been found in the composite catalysts by O-2-TPD-MS and electrical conductivity studies, which seems to be responsible for the enhanced selectivity of the propane oxidative dehydrogenation.

Performance of a Supersonic Model Combustor using Vaporized Kerosene Injection

Characteristics of supersonic combustion by injecting kerosene vapor into a Mach 2.5 crossflow at various preheat temperatures and pressures were investigated experimentally. A two-stage heating system has been designed and tested, which can prepare heated kerosene of 0.8 kg up to 820 K at pressure of 5.5 Mpa with minimum/negligible fuel coking. In order to simulate the thermophysical properties of kerosene over a wide range of thermodynamic conditions, a three-component surrogate that matches the compound class of the parent fuel was employed. The flow rate of kerosene vapor was calibrated using a sonic nozzle. Computed flow rates using the surrogate fuel are in agreement with the experimental data. Kerosene jets at various preheat temperatures injecting into both quiescent environment and Mach 2.5 crossflow were visualized. It was found that at injection pressure of 4 Mpa and preheat temperature of 550 K the kerosene jet was completely in vapor phase, while keeping almost the same penetration depth as compared to the liquid kerosene injection. Supersonic combustion tests were also carried out to compare the combustor performance for the cases of vaporized kerosene injection, liquid kerosene injection, and effervescent atomization with hydrogen barbotage, under the similar stagnation conditions. Experimental results demonstrated that the use of vaporized kerosene injection leads to better combustor performance. Further parametric study on vaporized kerosene injection in a supersonic model combustor is needed to assess the combustion efficiency as well as to identify the controlling mechanism for the overall combustion enhancement.

Aerodynamic characteristics research on wide-speed range waverider configuration

Waverider generated from a given flow field has a high lift-to-drag ratio because of attached bow shock on leading edge. However, leading edge blunt and off-design condition can make bow shock off leading edge and have unfavorable influence on aerodynamic characteristics. So these two problems have always been concerned as important engineering science issues by aeronautical engineering scientists. In this paper, through respectively using low speed and high speed waverider design principles, a wide-speed rang vehicle is designed, which can level takeoff and accelerate to hypersonic speed for cruise. In addition, sharp leading edge is blunted to alleviated aeroheating. Theoretical study and wind tunnel test show that this vehicle has good aerodynamic performance in wide-speed range of subsonic, transonic, supersonic and hypersonic speeds.