Effects of pH on the Interactions and Conformation of Bovine Serum Albumin: Comparison between Chemical Force Microscopy and Small-Angle Neutron Scattering

The conformation of bovine serum albumin (BSA), as well as its interactions with negatively charged mica surfaces in saline solutions of different pH values, have been studied by small-angle neutron scattering (SANS) and chemical force microscopy (CFM), respectively. A new approach to extract the contribution of elementary interactions from the statistically averaged force-extension curves through self-consistent fitting was proposed and used to understand the effects of pH on the interactions and conformation of BSA in saline solutions. When pH increases, the SANS results reveal that the sizes of BSA molecules increase slightly, while the statistical analysis of the CFM results shows that the averaged pull-off force for the elongation monotonously decreases. The decrease of pull-off force with the increase of pH results from the decrease in the strength of hydrogen bonding and the number of interaction pairs, as well as the slight increase of the strength of van der Waals interaction. When pH approaches the isoelectric point (pI) of BSA, results from both SANS and CFM suggest a loss of long-range interactions in BSA molecules. Our results also suggest that the force-extension curve is mainly contributed by the van der Waals interaction. The combination of SANS and CFM provides new insight to understand the interactions and conformation of BSA molecules

Investigation of sol-gel transition in Pluronic F127/D2O solutions using a combination of small-angle neutron scattering and Monte Carlo simulation

Physical gelation in the concentrated Pluronic F127/D2O solution has been studied by a combination of small-angle neutron scattering (SANS) and Monte Carlo simulation. A 15% F127/D2O solution exhibits a sol-gel transition at low temperature and a gel-sol transition at the higher temperature, as evidenced by SANS and Monte Carlo simulation studies. Our SANS and simulation results also suggest that the sol-gel transition is dominated by the formation of a percolated polymer network, while the gel-sol transition is determined by the loss of bound solvent. Furthermore, different diffusion behaviors of different bound solvents and free solvent are observed. We expect that this approach can be further extended to study phase behaviors of other systems with similar sol-gel phase diagrams.

Effect of annealing on the deformation mechanism of a styrene/n-butyl acrylate copolymer latex film investigated by synchrotron small-angle X-ray scattering

The deformation mechanism of a styrene/n-butyl acrylate copolymer latex film subjected to uniaxial tensile stress was studied by small-angle X-ray scattering. The influence of annealing at 23, 60, 80, and 100 degrees C for 4 h on microscopic deformation processes was elucidated. It was demonstrated that the microscopic deformation mechanism of the latex films transformed gradually from nonaffine deformation behavior to affine deformation behavior with increasing annealing temperature.

Structural evolution of tensile deformed high-density polyethylene at elevated temperatures: Scanning synchrotron small- and wide-angle X-ray scattering studies

The structural evolution of an ice-quenched high-density polyethylene (HDPE) subjected to uniaxial tensile deformation at elevated temperatures was examined as a function of the imposed strains by means of combined synchrotron small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS) techniques. The data show that when stretching an isotropic sample with the spherulitic structure, intralamellar slipping of crystalline blocks was activated at small deformations, followed by a stress-induced fragmentation and recrystallization process yielding lamellar crystallites with their normal parallel to the stretching direction. Stretching of an isothermally crystallized HDPE sample at 120 degrees C exhibited changes of the SAXS diagram with strain similar to that observed for quenched HDPE elongated at room temperature, implying that the thermal stability of the crystal blocks composing the lamellae is only dependent on the crystallization temperature.

Uniaxial deformation of overstretched polyethylene: In-situ synchrotron small angle X-ray scattering study

Synchrotron small angle X-ray scattering was used to study the deformation mechanism of high-density polyethylene that was stretched beyond the natural draw ratio. New insight into the cooperative deformational behavior being mediated via slippage of micro-fibrils was gained. The scattering data confirm on the one hand the model proposed by Peterlin on the static structure of oriented polyethylene being composed of oriented fibrils, which are built by bundles of micro-fibrils. On the other hand it was found that deformation is mediated by the slippage of the micro-fibrils and not the slippage of the fibrils. In the micro-fibrils, the polymer chains are highly oriented both in the crystalline and in the amorphous regions. When stretching beyond the natural draw ratio mainly slippage of micro-fibrils past each other takes place. The thickness of the interlamellar amorphous layers increases only slightly. The coupling force between micro-fibrils increases during stretching due to inter-microfibrillar polymer segments being stretched taut thus increasingly impeding further sliding of the micro-fibrils leading finally to slippage of the fibrils.

Non-affine structural evolution of soft colloidal crystalline latex films under stretching as observed via synchrotron X-ray scattering

A polymer dispersion consisting of soft latex spheres with a diameter of 135 nm was used to produce a crystalline film with face-centered cubic (fcc) packing of the spheres. Different from conventional small-molecule and hardsphere colloidal crystals, the crystalline latex film in the present case is soft (i.e., easily deformable). The structural evolution of this soft colloidal latex film under stretching was investigated by in-situ synchrotron ultra-small-angle X-ray scattering. The film exhibits polycrystalline scattering behavior corresponding to fcc structure. Stretching results not only in a large deformation of the crystallographic structure but also in considerable nonaffine deformation at high draw ratios. The unexpected nonaffine deformation was attributed to slippage between rows of particles and crystalline grain boundaries. The crystalline structure remains intact even at high deformation, suggesting that directional anisotropic colloidal crystallites can be easily produced.

高分子溶液中物理凝胶化的Monte Carlo模拟和小角中子散射研究

高分子凝胶广泛地存在于自然界以及日常生活中，按其形成作用力不同分为化学凝胶和物理凝胶两大类。由于高分子物理凝胶具有凝胶化的可逆性及其对环境条件强烈的响应性，因此，在近半个世纪的研究与应用中受到极大的关注。高分子溶液中的物理凝胶因其结构及形成机制复杂，在实验方面，除了散射技术及流变技术能够有效地揭示它的部分信息外，其它的实验手段很难用于这个领域的研究；在理论方面，化学凝胶的理论已经比较成熟，而物理凝胶的粘弹性质以及凝胶化是一个远离平衡态的松弛过程，除了一些特征的标度指数外，人们还没有得到适用于高分子物理凝胶的普适规律。当前，由于计算机模拟理论及模拟方法的发展，使得计算机模拟成为除了实验和理论研究方法之外的第三个重要的研究方法。但是，由于物理凝胶化行为的复杂性，用实验和理论获得的信息很难较好地描述凝胶化过程，而计算机模拟的高度透明性及反映信息的完整性，有助于理解这一复杂过程中所涉及的物理本质。因此，利用计算机模拟结合实验及理论方法深入研究高分子物理凝胶的形成机制、结构与性能关系已成为目前最有效的手段之一。 本论文主要运用Monte Carlo模拟方法，并结合小角中子散射（Small-Angle Neutron Scattering, SANS）和流变（Rheology）等实验手段从多个角度探讨了以下几类典型的高分子溶液物理凝胶化行为。 1. 温度对遥爪型三嵌段共聚物在选择性溶剂中的自组装及凝胶化行为影响的研究：采用二维简单方格子Monte Carlo模拟方法，结合逾渗（Percolation）理论，建立了溶胶－凝胶转变相图在统计热力学中的确定方法；甄别了具有特征构象的链，讨论了链及胶束的聚集，明晰了相互作用（体现为约化温度）、构象转变、聚集与凝胶化的一致的关联关系；提出了构象转变模型，进而明确了此体系的凝胶化过程，在微观尺度上表现为桥型链和环型链之间的竞争。 2. 模拟模型改进及其应用到持续长度对稀溶液中高分子链构象影响的研究：考虑到原始八位置键涨落模型效率低，实现复杂且不能应用到复杂的高分子体系，对该模型进行了改进，使其实现简单、效率高，并拓宽了该模型的应用范围。然后，以刚性对均聚物构象的影响为例，发现随着刚性增加，均聚物构象从球形椭球到棒状椭球的转变，并对比了自由连接链（Free Joint Chain, FJC）模型和蠕虫链（Wormlike Chain, WLC）模型在不同刚性范围内对高分子链末端距预测的偏差，首次给出了这两个经典模型的半定量的适用边界。 3. 溶剂尺寸对遥爪型三嵌段共聚物在选择性溶剂中的自组装及凝胶化行为影响的研究：用改进后的八位置键涨落Monte Carlo模型，研究了遥爪型三嵌段共聚物在选择性溶剂条件下的聚集和凝胶化对溶剂尺寸的依赖性，发现溶剂尺寸效应对凝胶化的作用是非单调的。由一个均聚物体系的对比模拟证明这种作用主要是由熵驱动的，并给出了中分子溶剂的半定量定义。在均聚物和嵌段共聚物溶液中，不同尺寸的溶剂分子可以使溶液由于高分子聚集不同而具有不同的微结构，并影响高分子链构象和溶液的性质。从多个角度研究了三嵌段共聚物在不同尺寸溶剂的溶液中所遵循的三种不同的凝胶化机理。 4. 聚氧化乙烯－氧化丙稀－氧化乙烯三嵌段共聚物（poly(ethylene oxide)-poly (propylene oxide)-poly-(ethylene oxide), PEO-PPO-PEO）重水溶液凝胶化的小角中子散射（SANS）和Monte Carlo研究：结合Pluronic F127（EO65PO99EO65）/D2O三嵌段共聚物溶液的特征，对照SANS数据，用改进后的八位置键涨落模型成功地从模拟中获得了F127/D2O的溶胶－凝胶转变相图。详细地考察了体系的微观结构，提出此类高分子溶液中形成的物理凝胶包含高分子逾渗网络的生成，以及被束缚溶剂（Bound Solvent）必须超过离散组分体系逾渗的临界体积分数的机理。着重研究了一定浓度的F127水溶液随温度升高引起的溶胶－凝胶转变以及凝胶－溶胶转变的Reentrant相行为，发现体系在低温区域的溶胶－凝胶转变遵循相同的机理，而在中等温度和较高温度以及不同浓度区域中的凝胶－溶胶转变遵循不同的机理。 5. 极性基团饱和度和溶剂条件对两亲性聚合物在溶液中的聚集行为和凝胶化影响的研究：用改进后的八位置键涨落模型，针对两亲性聚合物在不同溶剂条件的溶液建立了粗粒化模型，以两亲性聚合物中极性基团的饱和度，溶剂条件和高分子浓度为变量，考察了其对链构象、聚集及其凝胶化的影响。 6. 多糖水溶液凝胶化的流变和小角中子散射研究：用流变和SANS考察了两个多糖水溶液中物理凝胶化过程，针对由氢键主导的水基凝胶体系的典型特征进行了讨论，从分子链构象，聚集体结构及其关联以及流变特征等方面对聚强电解质角叉胶（Carrageenan）水溶液和聚弱电解质明胶（Pectin）水溶液进行了详细的讨论。考察了不同多糖的种类（聚合物链的电荷密度），盐的种类和浓度，溶液温度等对凝胶化和凝胶结构的影响，分析了不同多糖溶液的凝胶化机理。

Facile preparation of macroscopic soft colloidal crystals with fiber symmetry

A facile, efficient way to fabricate macroscopic soft colloidal crystals with fiber symmetry by drying a latex dispersion in a tube is presented. A transparent, stable colloidal crystal was obtained from a 25 wt % latex dispersion by complete water evaporation for 4 days. The centimeter-long sample was investigated by means of synchrotron small-angle X-ray diffraction (SAXD). Analysis of a large number of distinct Bragg peaks reveals that uniaxially oriented colloidal crystals with face-centered cubic lattice structure were formed.

Composition effect on dewetting of ultrathin films of miscible polymer blend

Two kinds of dewetting and their transition induced by composition fluctuation due to different composition in blend [poly(methyl methacrylate) (PMMA) and poly(styrene-ran-acrylonitrile) (SAN)] films on SiOx substrate at 145 degrees C have been studied by in-situ atomic force microscopy (AFM). The results showed that morphology and pathway of dewetting depended crucially on the composition. Possible reason is the variation in intensity of composition fluctuation resulted from the change of components in polymer blend. Based on the discussion of this fluctuation due to the composition gradient, parameter of U-q0/E, which describes the initial amplitude of the surface undulation and original thickness of film respectively, has been employed to distinguish the morphologies of spontaneous dewetting including bicontinuous structures and holes.

Preparation of Polyacrylamide Aqueous Dispersions Using Poly(sodium acrylic acid) as Stabilizer

High-solids, low-viscosity, stable polyacrylamide (PAM) aqueous dispersions were prepared by dispersion polymerization of acrylamide in aqueous solution of ammonium sulfate (AS) using Poly (sodium acrylic acid) (PAANa) as the stabilizer, ammonium persulfate (APS) or 2,2'-Azobis (N,N'-dimethyleneisobutyramidine) dihydrochloride (VA-044) as the initiator. The molecular weight of the formed PAM, ranged from 710, 000 g/mol to 4,330,000 g/mol, was controlled by the addition of sodium formate as a conventional chain-transfer agent. The progress of a typical AM dispersion polymerization was monitored with aqueous size exclusion chromatography. The influences, of the AS concentration, the poly(sodium acrylic acid) concentration, the initiator type and concentration, the chain-transfer agent concentration and temperature Oil the monomer conversion, the dispersion viscosity, the PAM molecular weight and distribution, the particle size and morphology were systematically investigated.

Pressure effects on thermodynamics of phase behavior in polystyrene/methylcyclohexane solutions

The calculations presented in this paper are based on the Sanchez-Lacombe (SL) lattice fluid theory. The interaction energy parameter, g*(12)/k, required in this approach was obtained by fitting the cloud points of polystyrene (PS) /methyleyclohexane (MCH) polymer solutions under pressure. The SL lattice fluid theory was used to calculate the spinodals, the binodals, and the Flory-Huggins (FH) interaction parameter of the solutions. The calculated results show that the SL lattice fluid theory can describe the dependences of thermodynamics of PS/MCH solutions on temperature and pressure very well. However, the calculated enthalpy and the excess volume changes indicate that the Clausius-Clapeyron equation cannot be suitable to describe pressure effect on PS/MCH solutions. Further analysis on the thermodynamics of this system under pressure shows that the role of entropy is more important than the excess volume in the present case.

Preparation of poly(acrylamide-co-acrylic acid) aqueous latex dispersions using anionic polyelectrolyte as stabilizer

High-solids, low-viscosity, stable poly(acrylamide-co-acrylic acid) aqueous latex dispersions were prepared by the dispersion polymerization of acrylamide (AM) and acrylic acid (AA) in an aqueous solution of ammonium sulfate (AS) medium using anionic polyelectrolytes as stabilizers. The anionic polyelectrolytes employed include poly(2-acrylamido-2-methylpropanesulfonic acid sodium) (PAMPSNa) homopolymer and random copolymers of 2-acrylamido-2-methylpropanesulfonic acid sodium (AMPSNa) with methacrylic acid sodium (MAANa), acrylic acid sodium (AANa) or acrylamide (AM). The influences of stabilizer's structure, composition, molecular weight and concentration, AA/AM molar feed ratio, total monomer, initiator and aqueous solution of AS concentration, and stirring speed on the monomer conversion, the particle size and distribution, the bulk viscosity and stability of the dispersions, and the intrinsic viscosity of the resulting copolymer were systematically investigated. Polydisperse spherical as well as ellipsoidal particles were formed in the system. The broad particle size distributions indicated that coalescence of the particles takes place to a greater extent.

Confined intra-molecular clustering in orientated polyethylene after annealing

Deuterated polyethylene tracer molecules with small amount of branches (12 C2H5- branches per 1000 backbone carbon atoms) were blended with a hydrogenated polyethylene matrix to form a homogenous mixture. The conformational evolution of the deuterated chains in a stretched semi-cry stall me film was observed via online small angle neutron scattering measurements during annealing at high temperatures close to the melting point. Because the sample was annealed at a temperature closely below its melting point, the crystalline lamellae were only partially molten and the system could not fully relax. The global chain dimensions were preserved during annealing. Recrystallization of released polymeric chain segments allows for local phase separation thus driving the deuterated chain segments into the confining interlamellar amorphous layers giving rise to an interesting intra-molecular clustering effect of the long deuterated chain. This clustering is deduced from characteristic small angle neutron scattering patterns. The confined phase separation has its origin in primarily the small amount of the branches on the deuterated polymers which impede the crystallization of the deuterated chain segments.