Molecularly imprinted solid-phase extraction sorbent for removal of nicotine from tobacco smoke

A sorbent showing specific affinity for nicotine was prepared by molecular imprinting technique, using nicotine as the template, methacrylic acid (MAA) as the functional monomer, ethyleneglycol dimethacrylate (EDMA) as the crosslinker and chloroform as the porogen. UV spectroscopic analysis in the molecular imprinting prepolymerization stage confirmed that nicotine could complex with the functional monomer by electrostatic interaction (ionic interaction and hydrogen bonding). The affinity and the binding properties of the imprinted polymer towards nicotine were investigated by equilibrium rebinding experiments. The results indicated the presence of nicotine-specific binding sites in the imprinted polymer, and that the imprinted polymer had a good capacity (90 mumol/g polymer) for nicotine. The elution conditions were optimized on the column packed with the imprinted polymer to elute nicotine quantitatively. The imprinted polymer was used as a solid-phase extraction (SPE) material for the removal of nicotine from tobacco smoke. The results obtained showed that the imprinted polymer was superior in terms of removing nicotine in tobacco smoke, compared with the commercial filter tip.

Recognition interactions of metal-complexing imprinted polymer

Molecularly imprinted polymer, exhibiting considerable enantioselectivity for L-mandelic acid, was prepared using metal coordination-chelation interaction. By evaluating the recognition characteristics in the chromatographic mode, the recognition interactions were proposed: specific and nonspecific metal coordination-chelation interaction and hydrophobic interaction were responsible for substrate binding on metal-complexing imprinted polymer; while the selective recognition only came from specific metal coordination-chelation interaction and specific hydrophobic interaction.

Short columns with molecularly imprinted monolithic stationary phases for rapid separation of diastereomers and enantiomers

Three molecularly imprinted monolithic columns with different length but almost identical column volume had been prepared. It was observed that the separation factors of diastereomers and enantiomers were almost unaffected by column length. However, the short column with dimension of 38 mm x 8 mm W. showed much lower resistance to flow rate so that it could be operated at much higher flow rates. By combining stepwise gradient elution with elevated flow rate, the diastereomers of cinchonine and cinchonidine and the enantiomers of Cbz-DL-Trp and Fmoc-DL-Trp were successfully separated within 3 min on the short column with dimension of 38 mm. x 8 mm i.d.. Based on the above results, a cinchonine imprinted monolithic disk with dimension of 10 mm x 16 mm W. was further developed. The SEM image and the pore size distribution profile showed that large flow-through pores are present on the prepared monolith, which allowed mobile phase to flow through the disk with very low resistance. Chromatographic performances on the monolithic disk were almost unchanged compared with the long columns. A rapid separation of cinchonine and cinchonidine was achieved in 2.5 min at the flow rate of 9.0 ml/min. Furthermore, it was observed that there was almost no effect of the flow rate on the dynamic binding capacity at high flow rates. In addition, the effect of the loading concentration of analytes on the dynamic binding capacity, namely adsorption isotherm, was also investigated. A non-linear adsorption isotherm of cinchonine was observed on the molecularly imprinted monolith with cinchonine as template, which might be a main reason to result in the peak tailing of template molecule. (C) 2004 Elsevier B.V. All rights reserved.

Molecularly imprinted monolithic stationary phases for liquid chromatographic separation of enantiomers and diastereomers

The method for preparation of molecularly imprinted monolithic stationary phase has been improved to achieve liquid chromatographic separation of enantiomers and diastereomers. By adopting low polar porogenic solvents of toluene and dodecanol and optimal polymerization conditions, the molecularly imprinted monolithic stationary phases with good flow-through properties and high resolution were prepared. Enantiomers of amino acid derivatives and diastereomers of cinchona alkaloids were completely resolved using the monolithic stationary phases. The influence of porogenic composition, monomer-template ratio and polymerization conditions on the chromatographic performance was investigated. Some chromatographic conditions such as the composition of the mobile phase and the temperature were characterized. Scanning electron microscopy showed that the molecularly imprinted monolithic stationary phase has a large through-pore structure to allow the mobile phase to flow through the column at very low backpressure. Accelerated separations of enantiomers and diastereomers were therefore achieved at elevated flow rates. Finally, the chiral recognition performance of the prepared stationary phase in aqueous media was investigated. Hydrophobic interaction, and ionic and/or hydrogen bonding interactions were proposed to be responsible for the recognition mechanism. (C) 2002 Elsevier Science B.V. All rights reserved.

Enantiomeric Recognition by Molecularly Imprinted Polymers Using Hydrophobic Interactions

Molecularly imprinted polymers prepared using acrylamide as the hydrogen bonding functional monomer exhibited good enantiomeric recognition properties in aqueous solutions. Our results indicate that the recognition improved with increased mobile phase water percentage and ionic strength, and was also very much pH dependent upon the ionisation properties of the sample molecules. The results can be interpreted in terms of specific hydrophobic interactions between the enantiomeric species and the recognition sites of imprinted polymers. A study of substrate selectivity showed differences between a pure organic system and a water/organic system as the mobile phases. The hydrophobicity of the test compounds was found to be an important parameter in determining the selectivity.

Effect of doped dye on the charge-carrier transport and electroluminescent performance in molecularly doped polymer light-emitting diodes

The effects of the concentration of 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H, 5H, 11H-(1)-benzopyropyrano(6, 78-i,j)quinolizin-11-one (C545T) as dopant in polyfluorene (PFO) on the charge-carrier transport and electroluminescence (EL) performance were investigated by steady-state and transient EL measurements. A fully green emission from C545T was observed and the EL performance depends strongly on the C545T concentration. The mobility in the C545T-doped PFO film was determined by transient EL. The dopant concentration dependence of the current-voltage relationship indicated clearly the carrier trapping by the C545T molecules. The mobility in C545T:PFO changed significantly with the C545T concentration, and showed a nontrivial dependence on the doping level. The behavior may be understood in terms of the formation of an additional energy disorder due to potential fluctuation caused by the Coulomb interaction of the randomly distributed doping molecules.

Capacitive detection of glucose using molecularly imprinted polymers

A novel glucose biosensor based on capacitive detection has been developed using molecularly imprinted polymers. The sensitive layer was prepared by electropolymerization of o-phenylenediamine on a gold electrode in the presence of the template (glucose). Cyclic voltammetry and capacitive measurements monitored the process of electropolymerization. Surface uncovered areas were plugged with 1-dodecanethiol to make the layer dense, and the insulating properties of the layer were studied in the presence of redox couples. The template molecules and the nonbound thiol were removed from the modified electrode surface by washing with distilled water. A capacitance decrease could be obtained after injection of glucose. The electrode constructed similarly but with ascorbic acid or fructose only showed a small response compared with glucose. The stability and reproducibility of the biosensor were also investigated. (C) 2001 Elsevier Science B.V. All rights reserved.

Phenylurea herbicides-selective polymer prepared by molecular imprinting using N-(4-isopropylphenyl)-N'-butyleneurea as dummy template

A phenylurea herbicides-selective molecularly imprinted polymer (MIP) was prepared using N-(4-isopropylphenyl)-N'-butyleneurea as a dummy template and toluene as a porogen. The experimental results showed that the optimum molar ratio of template, functional monomer (MAA) and cross-linker (EDMA) was 1:8:20. Scatchard analysis showed that two classes of binding sites were formed in the imprinted polymer with dissociation constants of 26.81 mu L mol l(-1) and 1.428 mmol l(-1). The affinity and selectivity of MIP for phenylurea herbicides were studied. Among the 14 phenylurea herbicides tested, the MIP prepared showed obviously high affinity and selectivity for 10 chemicals (monuron, diuron, isoproturon, fenuron, chlortoluron, difenoxuron, metoxuron, neburon, buturon and fluometuron) with dichloromethane containing 10% hexane as mobile phase while non-imprinted polymer showed very low affinity for all the phenylurea herbicides tested. The experimental and calculated results also indicated that the size and property of the group at the N' position of phenylurea molecules have great influence on the affinity of MIP for them and the recognition site is mainly located at the N' position of phenylurea herbicides. (c) 2005 Elsevier B.V. All rights reserved.

Nanoparticle-amplified Surface Plasmon Resonance Study of Protein Conformational Change at Interface

This paper reports the study of protein conformational change by Au nanoparticles (AUNPs)-amplified surface plasmon resonance (SPR) spectroscopy. Taking cytochrome c (Cyt c) as an example, this paper gives a detailed description of the construction of metal-protein-metal sandwich nanostructure consisting of an Au film underlayer, a cytochrome c intermediate layer and an AuNPs upper layer. The incorporation of AuNPs into SPR biosensing results in increased SPR sensitivity to protein conformational change as demonstrated by acid denaturation of Cyt c. It suggests the conformational change of surface-confined Cyt c leads to the distance and electromagnetic coupling variations of Au film-AuNPs.

Capillary electrochromatographic separation of ionizable compounds with a molecular imprinted monolithic cationic exchange column

A polymer-based monolithic capillary column imprinted with 4-aminopyridine (4-AP) was prepared by a thermally-initiated polymerization process; and its performance as a capillary electrochromatographic medium was evaluated in separating 4-AP and 2-AP isomers. The effects of experimental parameters, such as pH value and ionic strength of the buffer, the acetonitrile content in the mobile phase, and the applied voltage, on the resolution of these isomers had been carefully investigated. It was found that in the retention process there were interplays of multiple mechanisms of ion-exchange, molecular imprinting, and electrophoresis. These mechanisms allowed more sophisticated control of experimental parameters in the separation of ionizable compounds.

Sensitive biomimetic sensor based on molecular imprinting at functionalized indium tin oxide electrodes

We initially report an electrochemical sensing platform based on molecularly imprinted polymers (MIPs) at functionalized Indium Tin Oxide Electrodes (ITO). In this research, aminopropyl-derivatized organosilane aminopropyltriethoxysilane (APTES), which plays the role of functional monomers for template recognition, was firstly self-assembled on an ITO electrode and then dopamine-imprinted sol was spin-coated on the modified surface. APTES which can interact with template dopamine (DA) through hydrogen bonds brought more binding sites located closely to the surface of the ITO electrode, thus made the prepared sensor more sensitive for DA detection. Potential scanning is presented to extract DA from the modified film, thus DA can rapidly and completely leach out. The affinity and selectivity of the resulting biomimetic sensor were characterized using cyclic voltammetry (CV). It exhibited an increased affinity for DA over that of structurally related molecules, the anodic current for DA oxidation depended on the concentration of DA in the linear range from 2 x 10(-6) M to 0.8 x 10(-3) M with a correlation coefficient of 0.9927.In contrast, DA-templated film prepared under identical conditions on a bare ITO showed obviously lower response toward dopamine in solution.

染料掺杂聚合物薄膜放大自发发射和受激发射的研究

随着有机／聚合物电致发光材料在有机发光二极管上的应用以及有机晶体管和有机太阳能电池的研制成功，有机／聚合物电致发光材料的优异的光电性能、低廉的生产成本、简单的加工工艺、宽广的选材范围和良好的机械性能等优点极大地吸引科学家们的研究兴趣，并开始了有机／聚合物发光薄膜的放大的自发发射和受激发射行为的研究。有机分子和聚合物的诸多如易得、廉价、结构多样、功能易调节、大的横截面积、高的荧光量子效率和低的自吸收等优点使其制成的激光器在未来光纤通讯领域中呈现了诱人的应用前景。新的有机激光材料不断涌现、器件结构不断推陈出新、新的激发原理不断提出并得到修正已经成为有机／聚合物固体激光研究领域的三大特点。本论文以研究有机材料的激光特性为目的，通过对有机染料DCJTB和三芳胺取代1，8-蔡酰亚胺齐聚物掺杂聚合物薄膜的放大的自发发射和受激发射特性的研究，探讨实现低闭值、高增益光泵浦有机聚合物激光的方法及影响器件性能的因素，阐明放大自发发射的工作机制，为进一步探讨电泵浦有机聚合物激光器提供材料体系和理论依据。1、研究了DCJTB掺杂聚合物薄膜的放大自发发射特性，分析了光泵浦条件下光谱窄化的放大自发发射机制，对ASE增益和损耗进行了讨论和数值拟合，并对增益方程进行了饱和修正。DCJTB：PS薄膜具有较低的闺值（0．16mJ·Pulse~(_1)·cm-2）、高的增益系数（40．72cm-1）、低的损耗值2．49cm一l和高的荧光量子效率（70．4％），其波导增益的波长分布呈明显的洛仑兹分布，增益饱和是均匀展宽的。与DCM比较发现，自由体积是决定材料性能的重要因素，大的自由体积有利于实现低闭值、高增益。我们的研究结果表明，DCJTB是非常好的激光介质材料。2、从ASE的发射波长、ASE闭值、增益和损耗四个技术指标出发，详细研究了激发光波长、聚合物基体、旋涂速度及基片等对DCJTB：PS薄膜放大自发发射（ASE）的影响，短的激发波长和合适的基体材料可以显著地降低闭值和提高增益，薄膜厚度和基片也对ASE性能有很大影响。利用琢lord镜面体系，研究了DCJTB染料掺杂相列向液晶体系的分布反馈激光特性，在电场作用下，可以有效地对TE、TM两种模式的输出强度进行调解。3、把电子传输／发光有机小分子材料Alq3掺杂到DCJTB和C545T掺杂聚合物薄膜，研究了它们的放大自发发射特性。通过在不同激发光波长激发下不同Alq3掺杂浓度对ASE性能影响的研究，发现掺杂Alq3显著地降低了闭值，增加了增益和减小了损耗。由于Alq3是一种良好的半导体有机发光材料，Alq3的引入对电泵浦有机聚合物激光器的研究具有重要的意义。4、研究了三种在4位氨基位置引入不同三芳胺功能基团的红光1，8-蔡酞亚胺齐聚物的放大自发发射特性，研究结果表明，三芳胺取代1，8蔡酞亚胺齐聚物具有低阂值、高增益和低损耗的特点，显示了较小的浓度淬灭效应，即使掺杂浓度高到60％仍可以观察到放大的自发发射现象，表明三芳胺取代1，8茶酞亚胺是一类非常有应用前景的有机半导体激光材料体系。

Molecular imprinting of nitrophenol and hydroxybenzoic acid isomers: effect of molecular structure and acidity on imprinting

Three nitrophenol isomer-imprinted polymers were prepared under the same conditions using 4-vinylpyridine as a functional monomer. Different recognition capacities for template molecules were observed for the three polymers. Another imprinting system with stronger acidity than nitrophenol isomers, 2-hydroxybenzoic acid (salicylic acid) and 4-hydroxybenzoic acid, was imprinted using 4-vinylpyridine or acrylamide as functional monomer respectively. Both 4-hydroxybenzoic acid-imprinted polymers using the two monomers showed recognition ability for the template molecule. However, when acrylamide was chosen as functional monomer, the salicylic acid-imprinted polymer showed very weak recognition for the template molecule, whereas strong recognition ability of the resultant polymer for salicylic acid was observed with 4-vinylpyridine as functional monomer. It seems that the structure and acidity of template molecules is responsible for the difference in recognition, by influencing the formation and strength of interaction between template molecule and functional monomer during the imprinting process. An understanding of the mechanism of molecular imprinting and molecular recognition of MIPs will help to predict the selectivity of MIPs on the basis of template molecule properties. Copyright (C) 2003 John Wiley Sons, Ltd.

Preparation and Tribological Studies of Stearic Acid Self-Assembled Monolayers on Polymer-Coated Silicon Surface

We present a good alternative method to improve the tribological properties of polymer films by chemisorbing a long-chain monolayer on the functional polymer surface. Thus, a novel self-assembled monolayer is successfully prepared on a silicon substrate coated with amino-group-containing polyethyleneimine (PEI) by the chemical adsorption of stearic acid (STA) molecules. The formation and structure of the STA-PEI film are characterized by means of contact-angle measurement and ellipsometric thickness measurement, and of Fourier transformation infrared spectrometric and atomic force microscopic analyses. The micro- and macro-tribological properties of the STA-PEI film are investigated on an atomic force microscope (AFM) and a unidirectional tribometer, respectively. It has been found that the STA monolayer about 2.1-nm thick is produced on the PEI coating by the chemical reaction between the amino groups in the PEI and the carboxyl group in the STA molecules to form a covalent amide bond in the presence of N,N'-dicyclohexylcarbodiimide (DCCD) as a dehydrating regent. By introducing the STA monolayer, the hydrophilic PEI polymer surface becomes hydrophobic with a water contact angle to be about 105degrees. Study of the time dependence of the film formation shows that the adsorption of PEI is fast, whereas at least 24 h is needed to generate the saturated STA monolayer. Whereas the PEI coating has relatively high adhesion, friction, and poor anti-wear ability, the STA-PEI film possesses good adhesive resistance and high load-carrying capacity and anti-wear ability, which could be attributed to the chemical structure of the STA-PEI thin film. It is assumed that the hydrogen bonds between the molecules of the STA-PEI film act to stabilize the film and can be restored after breaking during sliding. Thus, the self-assembled STA-PEI thin film might find promising application in the lubrication of micro-electromechanical systems (MEMS).