Early development of germlings of Sargassum thunbergii (Fucales, Phaeophyta) under laboratory conditions

Morphology and culture studies on germlings of Sargassum thunbergii (Mertens et Roth) Kuntze were carried out under controlled laboratory conditions. Growth characteristics of these germlings grown under different temperatures (from 10 to 25A degrees C), irradiances (from 9 to 88 mu mol photons m(-2) s(-1)), and under blue and white light conditions are described. The development of embryonic germlings follows the classic "8 nuclei 1 egg" type described for Sargassaceae. Fertilized eggs spent 5-6 h developing into multicellular germlings with abundant rhizoids after fertilization. Under conditions of 20A degrees C, 44 mu mol photons m(-2) s(-1) and photoperiod of 12 h, young germlings with one or two leaflets reached 2-3 mm in length after 8 weeks. Temperature variations (10, 15, 20, 25A degrees C) under 88 mu mol photons m(-2) s(-1) significantly influenced the growth rate within the first week, although this effect became less obvious after 8 weeks, especially at 15 and 20A degrees C. Variation in germling growth was highly significant under different irradiances (9, 18, 44, 88 mu mol photons m(-2) s(-1)) at 25A degrees C. Low temperature (10A degrees C) reduced germling growth. Growth of germlings cultured under blue light was lower than in white light. Optimal growth of these germlings occurred at 25A degrees C and 44 mu mol photons m(-2) s(-1).

Formation and early development of tetraspores of Gracilaria lemaneiformis (Gracilaria, Gracilariaceae) under laboratory conditions

Morphological and culture studies of tetraspores of Gracilaria lemaneiformis were carried out under laboratory conditions. Relationships of germination rate, diameter and survival rate of tetraspores from 1st generation branches with grads of temperature and irradiance were determined, respectively. The result showed that 1st generation branches is in the majority of the tetraspores shedding and tetraspores from which had highest survival rates than other parts of the sporophytic plant. The time tetraspores used developing from giant unicells to diads, which both existed on the epidermis, then to tetraspores off the matrix, was only approximately 3 weeks all through. However, tetraspores spent more than two months developing into germlings of gametophytes. It was shown that temperature variation (10, 15, 25, 30 degrees C) with the light of 30 mu mol m(-2) s(-1) had significant effects on the germination rate and diameter, but had no apparent effect on survival rate (ANOVA, P < 0.01). Germination rates of tetraspores reached the maximum at 20 degrees C, which was significantly higher than those at other temperature levels (P < 0.01), whereas 15 degrees C seemed to be optimal temperature for the diameter. All the three growth parameters (germination rate, diameter and survival rate) yield highly significant variations with irradiance treatments at room temperature (ANOVA, P < 0.01). The optimal germination rate was detected at the irradiance of 30 mu mol m(-2) s(-1) (P < 0.01). The photon flux density which exceeds 480 nnol m(-2) s(-1) have apparently negative effect on diameter and survival rate. (c) 2005 Elsevier B.V. All rights reserved.

Experimental Studies of the Material Properties of the Forewing of Cicada (Homoptera, Cicadidae)

Detailed investigations on the structural and mechanical properties of the forewing of the cicada were carried out. Measurement of the structures of the wings showed that the thickness of the membrane of each cell and the diameter of each vein were non-uniform in both the longitudinal and transverse directions, and their means were approximately 12.2 and 133.3 mum, respectively. However, the aspect ratios of the wings and the bodies were quite uniform and were approximately equal to 2.98 and 2.13, respectively. Based on the measured thickness, mass and area of the membranes of the cells, the mean density and the mean area density of the wing were approximately 2.3 g cm(-3) and 2.8 x 10(-3) g cm(-2), respectively. In addition, the diameters of the veins of the wings, including the diameters of the holes in the vein of the leading edge, were examined. The mechanical properties of the wing were investigated separately by nanoindentation and tensile testing. The results indicated that the mean Young's modulus, hardness and yield stress of the membranes of the wings were approximately 3.7 Gpa, 0.2 Gpa and 29 Mpa, respectively, and the mean Young's modulus and strength of the veins along the direction of the venation of wings were approximately 1.9 Gpa and 52 Mpa, respectively. Finally, the relevant results were briefly analyzed and discussed, providing a guideline to the biomimetic design of the aerofoil materials of micro air vehicles.

Studies of polysaccharides from three edible species of Nostoc (cyanobacteria) with different colony morphologies: Structural characterization and effect on the complement system of polysaccharides from Nostoc commune

The cyanobacterium Nostoc commune Vaucher produces quite complex extracellular polysaccharides. The cyanobacterium is nitrogen fixing, and on growing the cyanobacterium in media with and without nitrogen, different types of extracellular polysaccharides were obtained. These were also different from the polysaccharides present in N. commune collected in the field. High pH anion exchange chromatography (HPAEC) of weak acid hydrolysates of the culture-grown material demonstrated that, in this case, HPAEC was useful for comparison of the different polymers. The main differences between the polymers from the field group and the culture-grown samples were the presence of substantial amounts of arabinose, 2-O-methylglucose, and glucuronic acid in the latter. Methylation studies also revealed a difference in the branching points on the glucose units between the field and cultured samples, being 1,4,6 for the first and 1,3,6 for the latter. The field acidic fraction gave, on weak acid hydrolysis and separation on BioGel P2 and HPAEC, 12 oligosaccharide fractions that were isolated and studied by different mass spectroscopy techniques. The structures of the oligosaccharides were determined, and two different series that can originate from two repeating pentamers were identified: GlcAl-4/6GlcM1-4Ga11-4Glc1-4Xyl and GlcAl-4/6Glc1-4Ga11-4Glc1-4Xyl. The difference between these oligosaccharides lies in the methyl substituent on carbon 2 of the glucose unit next to the nonreducing glucuronic acid unit. The polysaccharides from field material were shown to have a strong effect on the complement system.

STUDIES OF THE PROMISING MATERIAL COSI2 ON GAAS SUBSTRATES

The thermal stability of CoSi2 thin films on GaAs substrates has been studied using a variety of techniques. The CoSi2 thin films were formed by depositing Co(500 angstrom) and Si(1800 angstrom) layers on GaAs substrates by electron-beam evaporation followed by annealing processes, where the Si inter-layer was used as a diffusion/reaction barrier at the interface. The resistivity of CoSi2 thin films formed is about 30 muOMEGA cm. The Schottky barrier height of CoSi2/n-GaAs is 0.76 eV and the ideality factor is 1.14 after annealing at 750-degrees-C for 30 min. The CoSi2/GaAs interface is determined to be thermally stable and the thin film morphologically uniform on GaAs after 900-degrees-C/30 s anneal. The CoSi2 thin films fulfill the requirements in GaAs self-aligned gate technology.

Organic geochemical studies of sinking particulate material in China sea area(I) - Organic matter fluxes and distributional features of hydrocarbon compounds and fatty acids

Sinking particulate material collected from Nansha Yongshu reef lagoon and the continental shelf of the East China Sea by sediment traps has been analyzed and studied for the first time using organic geochemical method. The results show that about half of the sinking particulate organic matter in the two study areas are consumed before reaching the depth of 5 m to the sea floor and the degree of this consumption in Yongshu reef lagoon is larger than that in the continental shelf of the East China Sea. The distributions of hydrocarbons and fatty acids indicate that the minor difference of biological sources of sinking particulate organic matter exists between Yongshu reel lagoon and the continental shelf of the East China Sea, but they mainly come from marine plankton. Stronger biological and biochemical transformations of sinking particulate organic matter are also observed and the intensity of this transformation in Yongshu reef lagoon is greater than that in the continental shelf of the East China Sea. It is found that the occurrence of C-25 highly branched isoprenoid (HBI) diene may be related to the composition of diatom species.

Material response and failure mechanism of unidirectional metal matrix composites under impulsive shear loading

The material response and failure mechanism of unidirectional metal matrix composite under impulsive shear loading are investigated in this paper. Both experimental and analytical studies were performed. The shear strength of unidirectional C-f/A356.0 composite and A356.0 aluminum alloy at high strain rate were measured with a modified split Hopkinson torsional bar technique. The results indicated that the carbon fibers did not improve the shear strength of aluminum matrix if the fiber orientation aligned with the shear loading axis. The microscopic inspection of the fractured surface showed a multi-scale zigzag feature which implied a complicated shear failure mechanism in the composite. In addition to testing, the micromechanical stress field in the composite was analyzed by the generalized Eshelby equivalent method (GEEM). The influence of cracking in matrix on the micromechanical stress field was investigated as well. The results showed that the stress distribution in the composite is quite nonhomogeneous and very high shear stress concentrations are found in some regions in the matrix. The high shear stress concentration in the matrix induces tensile cracking at 45 degrees to the shear direction. This in turn aggravates the stress concentration at the fiber/matrix interface and finally leads to a catastrophic failure in the composite. From the correlation between the analysis and experimental results, the shear failure mechanism of unidirectional C-f/A356.0 composite can be elucidated qualitatively.

Preliminary Studies of Practicability of Laminar Plasma Surface Treatment Process

The basic remelting and cladding tests with laminar plasma technology on metals have been conducted in order to demonstrate the possibility of the technology applied in material surface modification. The experimental results show that the properties of the modified layers of the cast iron surface can be improved notably by the remelting treatment and those of the stainless steel by the cladding treatment. The related results are also verified by microscopic studies such as scanning electron microscopic (SEM) observations, energy dispersive spectra (EDS) analysis and the Vickers hardness measurements of the surface modified layers.

Wear Studies of Hydroxyapatite Composite Coating Reinforced by Carbon Nanotubes

Multi-walled carbon nanotubes (CNTs) have been successfully introduced into hydroxyapatite (HA) coatings using laser surface alloying. It is evident from transmission electron microscopy (TEM) observations that the CNTs present in the matrix still keep their multi-walled cylinder graphic structure, although they undergo the laser irradiation. Scratching test results indicated that the as-alloyed HA composite coatings exhibit improved wear resistance and lower friction coefficient with increasing the amount of CNTs in the precursor material powders. These composites have potential applications in the field of coating materials for metal implants under high-load-bearing conditions. (c) 2006 Elsevier Ltd. All rights reserved.

Influence of stochastic mesoscopic structure on macroscopic mechanical behavior of brittle material

A newly developed numerical code, MFPA(2D) (Material Failure Process Analysis), is applied to study the influence of stochastic mesoscopic structure on macroscopic mechanical behavior of rock-like materials. A set of uniaxial compression tests has been numerically studied with numerical specimens containing pre-existing crack-like flaw. The numerical results reveal the influence of random mesoscopic structure on failure process of brittle material, which indicates that the variation of failure mode is strongly sensitive to the local disorder feature of the specimen. And the patterns of the crack evolution in the specimens are very different from each other due to the random mesoscopic structure in material. The results give a good explanation for various kinds of fracture modes and peak strength variation observed in laboratory studies with specimens made from the same rock block being statistically homogenous in macro scale. In addition, the evolution of crack is more complicated in heterogeneous cases than in homogeneous cases.

Effect of Surface Condition of Electrode on the Surface Melting of Material by Laser-Guided Micro-Arc Discharge

This paper studies the surface melting in the atmosphere by YAG laser-guided micro-arc discharge. In three kinds of surface conditions (free, oiled, and polyethylene covered), we try to control the diameter and the power density of discharge pit. It is found that the power density of 3 x 10(6) W/cm(2) of discharge pit on the oiled surface is moderate to form the melted layer thicker than that of the others, adapting to strengthen the surface of material, and the power density of 1.07 x 10(7) W/cm(2) of discharge pit on the polyethylene-covered surface is highest to form the deepest discharge pit among them, adapting to remove the material.

Molecular dynamics studies of brittle fracture of SiO2

By applying for molecular dynamics (MD) simulation and Griffith fracture criterion, the brittle behavior of crack extension of mode I type is investigated. The critical stress intensity factor (SIF)K-Ic(MD) of crack extension is calculated, and the evolution of atoms near crack tip is observed. It is found that K-Ic(MD) is in good agreement with the Griffith ftacture criterion K-Ic(Griffith).