Enhanced cycling performance and high energy density of LiFePO4 based lithium ion batteries

LiFePO4 attracts a lot of attention as cathode materials for the next generation of lithium ion batteries. However, LiFePO4 has a poor rate capability attributed to low electronic conductivity and low density. There is seldom data reported on lithium ion batteries with LiFePO4 as cathode and graphite as anode. According to our experimental results, the capacity fading on cycling is surprisingly negligible at 1664 cycles for the cell type 042040. It delivers a capacity of 1170 mAh for 18650 cell type at 4.5C discharge rate. It is confirmed that lithium ion batteries with LiFePO4 as cathode are suitable for electric vehicle application. (c) 2007 Elsevier B.V. All rights reserved.

Irreversible capacity loss of graphite electrode in lithium-ion batteries

The irreversible capacity loss of the carbon electrode in lithium-ion batteries at the first cycle is caused mostly by surface film growth. We inspected an unknown irreversible capacity loss (UICL) of the natural graphite electrodes. The charge/discharge behavior of graphite and meso-phase carbon microbeads heat-treated at 2800 degrees C (MCMB28) as the materials of the carbon anode in the lithium-ion battery were compared. It was found that the capacity loss of the natural graphite electrode in the first cycle is caused not only by surface film growth, but also by irreversible lithium-ion intercalation on the new formed surface at the potential range of lithium intercalation, while the capacity loss of the MCMB28 electrode is mainly originated from surface film growth. The reason for the difference of their irreversible capacity losses of these two kinds of carbon material was explained in relation to their structural characteristics. (C) 1997 Published by Elsevier Science S.A.

Carbon materials for lithium ion batteries

The preliminary work indicated that passive film is the most important factor influencing cell performance of carbon anode, and the carbon and solvent used govern cell performance by forming the passive film of different properties. A in situ XRD result is also presented.

A study of cokes used as anodic materials in lithium ion rechargeable batteries

A variety of cokes pretreated at different temperatures are used as anodic materials and their electrochemical characteristics are examined by cyclic voltammetry. It is found that for some cokes such as petroleum coke (preheated at 1300 degrees C), pitch coke (1300 degrees C), needle coke (1900 degrees C), metallurgical coke (1900 degrees C), high capacity and cyclic efficiency are achieved. Needle coke (1900 degrees C) and metallurgical coke (1900 degrees C) in particular give a capacity of over 200 mAh/g and a cyclic efficiency of nearly 100%, whereas poor performance is exhibited by those pretreated at higher or lower temperatures, e.g., petroleum cokes (500 degrees C, 2800 degrees C), pitch coke (500 degrees C) and needle coke (2800 degrees C). The cyclic voltammograms show two electrochemical processes, one at about 0.1 V vs. Li+/Li which is electrochemically reversible, and may be attributed to the intercalation/deintercalation of lithium ions while the other, at about 0.6 V vs. Li+/Li, is electrochemically irreversible and may be assigned to the decomposition of the electrolyte solvent, which leads to formation of the passive film on the anode surface. The experimental results strongly suggest that the pretreatment temperature of cokes and of the solvent are determining factors for the growth, structure and properties of the passive film.

Preparation of Microporous Membranes by Swift Heavy Ion Irradiation and Impedance Characterization

Polypropylene (PP) microporous membranes were successfully prepared by swift heavy ion irradiation and track-etching. Polypropylene foils were irradiated with Au-197 ions of kinetic energy 11.4 MeV.u(-1) (total energy of 2245.8 MeV) and fluence 1x10(8) ions.cm(-2) at normal incidence. The damaged regions produced by the gold ions along the trajectories were etched in H2SO4 and K2Cr2O7 solutions leading to the formation of cylindrical pores in the membranes. The pore diameters of the PP microporous membranes increased from 380 to 1610 nm as the etching time increased from 5 to 30 min. The surface and cross-section morphologies of the porous membranes were characterized by scanning electron microscopy (SEM). The micropores in the membranes were found to be cylindrical in shape, homogeneous in distribution, and equal in size. Some mathematical relations of the porosity of the PP microporous membranes were established by analytic derivation. The microporous membranes were used in lithium-ion batteries to measure their properties as separators. The electrical conductivity of the porous membrane immersed in liquid electrolyte was found to be comparable to that of commercial separators by electrochemical impedance spectroscopy (EIS). The results showed that the porosity and electrical conductivity were dependent on the ion fluence and etching time. By adjusting these two factors, microporous membranes with good porosity and electrical conductivity were made that met the requirements for commercial use.

利用重离子辐照技术制备锂离子电池隔膜；Preparation Lithium-ion Battery Separator by Swift Heavy Ion Irradiation Methods

用能量11.4MeV/u和注量1×108ions/cm2的197Au离子垂直辐照聚丙烯薄膜,通过电导测量法监测温度、硫酸浓度和重铬酸钾浓度对径迹蚀刻速率的影响,得到合适的蚀刻条件;成功制备出孔径范围在600—1000nm的重离子径迹聚丙烯孔膜,并用场发射扫描电镜对孔的形状及孔径大小进行了表征,对孔洞锥角的形成进行了分析,为重离子辐照技术制备锂离子电池隔膜提供了实验数据。

Lithium ion conducting polymer electrolytes based on alternating maleic anhydride copolymer with oligo-oxyethylene side chains

A comb polymer with oligo-oxyethylene side chains of the type -(CH2CB2O)(12)CH3 was prepared from methyl vinyl ether/maleic anhydride copolymer and poly (ethylene glycol) methyl ether. The polymer can dissolve LiClO4 salt to form homogeneous amorphous polymer electrolyte. The ac ion conduction was measured using the complex impedance method, and conductivities were investigated as functions of temperatures and salt concentration. The complexes were first found to have two classes of glass transition which increase with increasing salt content, The optimum conductivity attained at 25 degrees C is in the order of 5.50 x 10(-6)Scm(-1). IR spectroscopy was used to study the cation-polymer interaction.

DEVELOPMENT OF CYLINDRICAL SECONDARY LITHIUM POLYANILINE BATTERIES

The cylindrical 'D'-size batteries were fabricated by polyaniline paste cathode and lithium foil anode sandwiched with microporous polypropylene separator. The electrolyte used was LiClO4 dissolved in a mixed solvent of propylene carbonate and dimethoxyethane. The results of charge/discharge curves, charge/discharge cycles, the short-circuit current, the open-circuit voltage storage and the change of discharge capacity with temperature, discharge current are reported.

聚合物锂离子电池和生物燃料电池的相关研究

本论文分为两个部分研究了铿离子电池和生物燃料电池中的关键材料，主要的创新点和结论如下。采用聚合物电解质是提高铿二次电池性能的有效方法之一。聚合物电解质良好电导率、高铿离子迁移数、宽电化学窗口以及好的机械性能是其应用于铿二次电池中的关键。论文的第一部分主要讨论了聚合物、增塑剂和无机纳米粒子等对复合电解质体系的化学和物理性质的影响。我们采用溶液浇注一浸渍法制备了各种纳米复合聚合物电解质，例如开发出基于PVDFHFP或梳状聚合物基体的全固态以及聚合物和碳酸醋形成的胶体聚合物电解质体系。首次制备了具有较高离子电导率的单离子聚合物电解质。考察了两类纳米粒子填充物对体系的影响：一种是“惰性”发烟硅；另一种是“活性”蒙脱土。比较了全固态和胶体聚合物电解质体系电化学性质的不同之处。采用电化学交流阻抗，示差扫描量热法，X衍射，拉曼光谱，红外光谱，扫描电镜，循环伏安等方法详细研究了聚合物电解质中各组分对体系离子电导率和机械性能的影响。研究结果表明，纳米复合物为开发具有特定电化学和机械性能的电解质提供了一种有效的途径，它对聚合物电解质的物理性质影响明显。纳米粒子的加入增强了体系的机械性能，同时也使体系对溶剂的吸附能力增加。在全固态聚合物电解质中加入增塑剂，形成胶体态聚合物电解质，体系的电导率大大增加。所制备的胶体复合物电解质的室温电导率可以达到10-3s cm-1的数量级，机械强度好，阳离子迁移数高。指出选择合适的添加剂及复合方法，控制界面的结构和形态，形成尽可能多的高导电的界面，是获得电导率高和机械性能良好的聚合物电解质的有效途径。并讨论了聚合物电解质在铿离子电池中的应用。 近年来，针对生物燃料电池的研究得到了广泛关注，其中实现蛋白质酶分子和电极之间的直接电子传递是研究中的热点。论文的第二部分主要研究了生物燃料电池中的酶电极。通过对碳纳米管（MWNTs）进行预处理，使其表面带有功能性官能团，从而可以实现酶分子在碳纳米管表面的固定，同时还保持了其生物活性。采用吸附法将微过氧化物酶-11（MP-11）或葡萄糖氧化酶（GOx）等生物分子固定到MWNTs上制成酶修饰电极，研究MWNTs对酶和电极之间电子传递的促进作用。当酶分子（MP-11，GOX）固定到MWNTs表面后，循环伏安结果显示出一对可逆的氧化还原峰，对应酶分子的直接电子转移。研究结果表明这种方法可以扩展到固定其他生物酶分子以及实现蛋白质酶分子和电极之间的直接电化学，可以获得一系列氧化还原酶分子的电化学参数，如反应速率常数等。同时，我们还研究了酶修饰电极对其底物的电催化反应。研究结果表明，该修饰电极对底物的电化学反应表现出较好的催化活性。我们还研究了酶分子在MWNTs修饰铂微电极上的电化学行为。这些研究为研制生物燃料电池提供了一种固定酶以及制备电极材料较好的方法。

Enhanced electrochemical properties of nanocomposite polymer electrolyte based on copolymer with exfoliated clays

In this present work, a polymer electrolyte based on polymer/clay nanocomposite has been developed. Montmorillonite (MMT) clay was used as the filler. due to its special size in length and thickness, and its sandwich type structure. The obtained gel polymer electrolytes have high ionic conductivity up to 2.5 mS cm(-1) with high cationic transference number (about 0.64) at room temperature. The influences of the filler on the membrane morphology. the solvent uptake, the ionic conductivity, and the cation transport number were investigated, and thus the significant contribution from the exfoliated organophilic MMT was identified.

Polyaniline-coated carbon particles and their electrode behavior in organic carbonate electrolyte

In an attempt to increase the interface stability of carbon used in Li-ion batteries, a thin conducting polyaniline (PANI) film was fabricated on the surface of carbon by in situ chemical polymerization. The chemical and electrochemical properties of the composite material were characterized using X-ray diffraction, Raman spectroscopy, scanning electron microscope, cyclic voltammetry, and electrochemical impedance spectroscopy. It was confirmed that the PANI film has an obvious effect on the morphology and the electrochemical performance of carbon. The results could be attributed to the electronic and electrochemical activity of the conducting PANI films.

Poly(vinylidene fluoride-hexafluoropropylene)/organo-montmorillonite clays nanocomposite lithium polymer electrolytes

Polymer-clay nanocomposite (PCN) materials were prepared by intercalation of an alkyl-ammonium ion spacing/coupling agent and a polymer between the planar layers of a swellable-layered material, such as montmorillonite (MMT). The nanocomposite lithium polymer electrolytes comprising such PCN materials and/or a dielectric solution (propylene carbonate) were prepared and discussed. The chemical composition of the nanocomposite materials was determined with X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy, which revealed that the alkyl-ammonium ion successfully intercalated the layer of MMT clay, and thus copolymer poly(vinylidene fluoride-hexafluoropropylene) entered the galleries of montmorillonite clay. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were used to investigate the electrochemical properties of the lithium polymer electrolyte. Equivalent circuits were proposed to fit the EIS data successfully, and the significant contribution from MMT was thus identified. The resulting polymer electrolytes show high ionic conductivity up to 10(-3) S cm(-1) after felling with propylene carbonate.

Ag~+-Li~+离子交换制作Er~(3+)/Yb~(3+)共掺磷酸盐玻璃平面光波导(英文)

制备了化学稳定的Er^3＋／Yb^3＋共掺的磷酸盐玻璃，并在其中制作了用于光放大器和激光器的平面光波导．这种磷酸盐玻璃的失重速率为4．7×10^-5g·cm^-2·hr^-1，小于Kigre公司商业化的磷酸盐玻璃QX／Er的失重速率．采用Ag^＋-Li^＋交换技术制作了平面光波导并用m-线光谱在632．8nm测量了平面光波导的有效折射率．根据反WKB法得到折射率形貌，计算了离子交换参数如：离子交换深度、表面折射率，折射率改变和扩散系数等．

利用重离子辐照及蚀刻技术制备锂离子电池隔膜

本文通过对目前锂离子电池市场及锂离子电池隔膜制备现状的研究，提出采用重离子辐照技术制备锂离子电池隔膜的新方法。拓展了重离子辐照技术的应用，为锂离子电池隔膜的国产化另辟蹊径。实验中，用能量25 MeV/u 的Kr86及11.4 MeV/u的197Au离子，以1×108 cm-2-5×109 cm-2剂量辐照聚丙烯薄膜，通过电导测量法监测蚀刻液的参数，包括温度、硫酸浓度、重铬酸钾浓度对径迹蚀刻速率的影响，得到适合的蚀刻条件；并用场发射扫描电镜对孔的形状及孔径大小进行表征；成功制备出孔径均匀、具有密度和大小可控的重离子径迹聚丙烯孔膜；对孔洞锥角的形成进行分析，给出锥角的计算公式，为利用重离子辐照技术制备锂离子电池隔膜提供了实验数据