Reflection of shock-wave in pur foam from rigid wall

Keller proposed that a building, a mechanical installation or a body wrapped bya layer of foam plastics may be an efficient means for protection from damage ofblast wave. However, the practical effect was beyond expectation. For example, agunner wearing the foam plastics-padded waistcoat was injured more seriously by theblast wave from a muzzle. Monti took the foam plastics as homogeneous two-phasemedium and analyzed it with the theory of dusty flow. The obtained results showthat the peak pressure behind the reflected shock wave from rigid wall with foamcoat exceeds obviously that without foam coat under the same condition. Gel'fand,Patz and Weaver made experimental observations by means of shock tubes and veri-

外差干涉仪混频误差分析

共光路外差干涉仪具有很高的分辨率．但因为安装、调试误差会产生非线性误差．影响系统的测量精度。着重分析了在共光路外差干涉仪中由激光光源的椭圆偏振化和沃拉斯顿棱镜的安装方位角误差同时存在的情况下，引起的频率混叠综合误差的大小及变化规律。结果发现其造成的非线性误差可达2．2nm，同时还发现两者造成的误差在某些情况下存在一定程度的相互抵消作用。讨论了提高测量系统精度的有效措施，对正确设计和调试激光外差测试系统、提高测量系统精度具有重要意义。

大型制冷机组的冲洗与调试

大型制冷机组部件众多，管路比较复杂，又是必须承受高压的容器，安装、调试都有严格的要求。以30HXC165A制冷机组的现场冲洗、调试为例，详细介绍了大型制冷机组在试运行之前标准的准备工作。这些工作包括吹扫、试压、排污、充注制冷剂和冲洗调试等全部过程及注意事项。本文为大型螺杆式制冷机组这种压力容器设备的运行和维护管理提供了工程实践经验。结果表明：在施工调试过程中，只有各方互相协调，并且严格按照相关文件和规范要求才能顺利完成制冷机组的安装调试，为以后的正常运行打下基础。

新型渗透变形仪的研制

针对现有渗透变形仪存在的密封止水效果差、试样固定装置影响过流面积、仪器复杂等缺陷,通过对岩土渗透变形特性及测试原理进行分析,研制出一种适用于黏性土、水泥土类的新型渗透变形仪,该仪器设计方法独特,在试样外套橡皮膜并加围压的柔性密封止水,以及在试样顶部采用圆环型透水石固定试样等方法,既能测定岩土体的渗透系数又能测定渗透变形特性,同时,既保证试样的渗流面积不受影响又允许试样产生渗透变形,而且在渗透水压力作用下试样周围的密封性良好。实际工程应用结果表明,该仪器测定的岩土体的渗透系数及抗渗比降具有很高的可靠性和精度。

八单元一维位置灵敏雪崩室

In the experiment of nuclear reaction, it is important to measure the mass, charge, energy and emitted direction of particles. For multiparameter measurement, we must use a detector or a group of detectors which can give the time, energy, and position information. The Large Area position sensitive Ionization Chamber(LAIC) is one of the eight experiment terminals of HIRFL. It is built for researching nuclear reactions from low energy to intermediate energy. It is an excellent equipment for energy measurements and atomic number identification of emitted fragments in this energy region. It is also designed to give the time and position information of the emitted fragments by itself. Obviously, an IC can not supply a good timing signal. Moreover, the mechanical installation is different from the original design by some other reasons. In this case, it is not enough to obtain the correct direction information of the emitted fragments. To obtain good timing signals and the correct direction information, some modifications must be made. It is well known that a PPAC can give us excellent timing signals. It also can be easily built as a position sensitive detector. For this reason, a specially designed PPAC is installed in the entrance of the LAIC. For the different purposes, two types of PPACs were designed and tested. Both are OCTPSACs (OCTunit one dimension Position Sensitive Avalanche Counter). In this paper, both OCTPSACs will be introduced. Based on the requirements of the LAIC, the OCTPSACs consist of eight position sensitive PPACs. Each PPAC has an anode and a cathode. In both cases, the sizes are same. But different type of cathodes are used. In one type of OCTPSAC, its cathode is made of wire plane. It consists of gold-plated tungsten wires with the diameter of 20μm, spaced 0.5 mm apart from each other. The anode is a mylar foil which was evaporated by gold layer with the thickness of 50μg/cm~2 mounted on a printed plate in the shape of rectangle. the thickness of mylar foil is 1.5μm. The gap between anode and cathode is 3mm. The performance of the OCTPSAC has been tested by using a ~(252)Cf source in flowing isobutylene gas at the pressure of 3.4mb. The intrinsic time resolution of 289ps and position resolution of 2 mm have been obtained. In another type of OCTPSAC, the cathode is made of mylar foil, which is composed of gold strip by vacuume evaporation method with a special mask on the mylar foil. The thickness and the width of the gold strip is 50μg/cm~2 and 1.7mm. The strips are spaced 0.3 mm apart from each other. The anode is the same as the former type. We have obtained the time resolution of 296ps and position resolution of 2mm by using ~(241)Am-a source when the gas pressure is 6 mb and high voltage is 600V. The working gas is heptane

Facile synthesis of ginsenoside Ro

Two concise synthetic routes, being different in the glycosylation sequence, toward ginsenoside Ro (1) are developed. These syntheses feature the elaboration of the glucuronide residue at a later stage via the TEMPO-mediated selective oxidation and the installation of AZMB as a benzoylic neighboring participating group capable of being selectively removed afterward.

黄土高原土壤侵蚀与旱地农业国家重点实验室土壤侵蚀模拟实验大厅降雨装置

黄土高原土壤侵蚀与旱地农业国家重点实验室土壤侵蚀模拟实验大厅自 1 992年竣工以来运转正常 ,在降雨面积之大、降雨强度调节范围之宽、降雨特性与天然降雨之接近程度、以及自动化控制程度等方面 ,目前均为全国之最。在土壤侵蚀实验研究中发挥了重要作用。在论述土壤侵蚀模拟实验重要意义的基础上 ,简要介绍了有关模拟降雨装置 (包括降雨喷头、供水管网等 )的设计依据、选型和布设安装等情况 ,并介绍了模拟降雨的基本特征。

基于无线通信的阀门泄漏检测系统

阀门泄漏的在线监测一直是困扰流程工业的难题,采用传统有线监控方式需要巨大的布线安装成本。本文通过结合无线通信技术和超声检测技术,研究并开发了一种基于无线通信的阀门泄漏检测系统,可极大地降低测控系统的投资和使用成本,通过实时检测阀门的工作状态,及时发现并定位泄漏位置,实现工业生产的节能降耗。

新型4自由度并联机器人位姿误差分析

将一种新型四自由度并联机器人等效为由串联机构构成的空间闭环机构 ,运用 Denavit- Hartenberg方法提出了运动平台位姿误差的一种分析算法。利用这个算法可以分析各种构件加工、安装误差对运动平台位姿精度的影响。进行了数值仿真验证了算法的正确性。最后分析出对位姿精度影响较大的因素 ,通过重视这些因素可提高实际机构的操作精度

线性电位器的非线性传递函数分析

在线性电位器的电路设计中、电路前后级的输出和输入阻抗的影响以及使用与安装不当都可能引入非线性,造成电路和控制系统的精度达不到要求。为此,针对电位器的调节输出电压、限定调节范围、负载等效阻抗、细调等几种典型电路中的传递函数与非线性响应,通过实验给出了线性和非线性输出响应曲线。阐述了实际应用中如何避免和减少非线性的影响。

Mini-electrochemical detector for microchip electrophoresis

This paper presents the development of a mini-electrochemical detector for microchip electrophoresis. The small size (3.6 x 5.0 cm(2), W x L) of the detector is compatible with the dimension of the microchip. The use of universal serial bus (USB) ports facilitates installation and use of the detector, miniaturizes the detector, and makes it ideal for lab-on-a-chip applications. A fixed 10 M Omega feedback resistance was chosen to convert current of the working electrode to voltage with second gain of 1, 2, 4, 8, 16, 32, 64 and 128 for small signal detection instead of adopting selectable feedback resistance. Special attention has been paid to the power support circuitry and printed circuit board (PCB) design in order to obtain good performance in such a miniature size. The working electrode potential could be varied over a range of +/-2.5 V with a resolution of 0.01 mV. The detection current ranges from -0.3 x 10(-7) A to 2.5 x 10(-7) A and the noise is lower than 1 pA. The analytical performance of the new system was demonstrated by the detection of epinephrine using an integrated PDMS/glass microchip with detection limit of 2.1 mu M (S/N = 3).