重组人甲状旁腺素(rhPTH(1-84))的原核表达及发酵条件初步优化

下载PDF阅读器甲状旁腺激素(Parathyroid Hormone,PTH)是治疗骨质疏松症的药物之一.将人工合成全长人PTH(hPTH(1-84))的核苷酸序列插入pThioHis A载体中,然后转化大肠杆菌(Escherichia coli.),在IPTG的诱导下,成功实现了rhPTH(1-84)的原核表达.通过发酵条件的优化,初步确定1:40接种.LB+30% M9盐溶液的发酵培养基,37℃培养至OD600nm=0.8时,加入终浓度为0.6 mmol/L的IPTG,诱导8 h的较优发酵程序.

己酸乙酯酯化真菌筛选及发酵条件研究

本文主要研究了具有己酸乙酯酯化活性的真菌菌株的筛选和发酵条件优化。从大曲和糟醅样品中分离纯化获得79株产生透明圈的丝状真菌，菌落形态初步识别结果显示分离菌株包括红曲霉属、根霉属及曲霉属等菌株。其中菌株EM-56酯化酶活力最强，发酵获得的粗酶制剂酶活为172.36 u。根据显微形态、菌落形态及生理生化特征，初步鉴定该菌株为曲霉科红曲霉属紫色红曲霉（Monascus purpureus）。 在此基础上重点研究了菌株EM-56在不同培养基成分及不同培养条件下的产酶情况，确定了最佳培养基和培养条件。通过单因素实验确定在基础培养基中添加最佳碳源为葡萄糖，最佳氮源为蛋白胨。正交优化实验结果确定了最佳培养基组成：以麸皮为基础培养基，添加葡萄糖 2%，蛋白胨 0.3 %，KH2PO4.3H2O 0.05 %，MgSO4.7H2O 0.06 %。菌株EM-56在上述培养基中的最佳发酵条件为：初始pH 5.5，发酵温度为35°C，发酵时间7d，种龄48h，接种量8%，装瓶量50g / 瓶（500mL）。在最佳培养基和发酵条件下，菌株EM-56发酵获得的粗酶制剂酶活达到241.56 u，比优化前提高了40.15%。 In this paper, the research focuses on the selection of fungus with esterifying activity and optimization of fermentation conditions. We isolated 79 strains which had transparent zones from Daqu and fermented grains. The isolated strains contained Monascus、Rhizopus and Aspergillus through primary morphology analysis. The strain of EM-56 which produces strongest esterase was selected. The enzyme activity reached 172.36u. According to related literature, EM-56 was identified as Monascus purpureus through morphology analysis and biochemical determination. We also studied the effects of different medium and fermentation conditions on the esterase production of strain EM-56. The optimal medium and fermentation conditions were determined. Single factor experiment result shows that the optimal carbon source added is glucose and the optimal nitrogen source added is peptone. The optimal fermentation medium determined by orthogonal optimization test is as follows: wheat bran as substrate, glucose 2%, peptone 0.3%, KH2PO4.3H2O 0.05%，MgSO4.7H2O 0.06%. The optimal fermentation conditions are: initial pH 5.5, cultural temperature 35°C, cultural time 7d, seed age 48h, inoculation 8%, medium mass 50g / flask（500mL）. The esterse activity of EM-56 cultivated in the optimal medium and fermentation conditions reached 241.56u and increased by 40.15% compared with the original activity.

微生物法生成辅酶Q10的研究

本文根据我们实验室建立的发酵产物中辅酶Q10定性定量检测方法，筛选得到一株可以代谢产生较多辅酶Q10的野生菌株放射形土壤杆菌(Agrobacterium radiobacter No.50)。 为了提高放射形土壤杆菌的辅酶Q10的产量，本实验利用液体培养研究了单因素对菌株辅酶Q10产量的影响，并用正交法确定了最佳液态发酵条件。最佳发酵培养基是：葡萄糖20g,蔗糖40g, 硫酸铵10g,玉米浆30g, 酵母膏3g，K2HPO4 3g,MgSO4.7H2O 1g，蒸馏水1000mL,pH 7.0-7.2。最佳发酵条件是：转接斜面菌种到种子培养基, 转速220r/min、温度28。C培养24h后，转入发酵培养基(250mL三角拼装液量为50mL，pH 7.0), 接种量为10％，转速220r/min、温度28。C，培养120h。在此条件下，菌体湿重约为50g/L，辅酶Q10含量约为20mg/L。 本文以放射形土壤杆菌为出发菌株进行诱变育种，以期获得辅酶Q10高产菌。根据微生物育种原理、参照辅酶Q10的代谢调控机制，以野生型放射形土壤杆菌(Agrobacterium radiobacter No.50)为出发菌株，采用紫外线和亚硝基胍复合诱变技术，依次筛选得到菌体提取物M抗性菌ARM－7、烟草提取物T抗性菌株ARMT-26、Vk3抗性菌株ARMTV-25、链霉素抗性菌株ARMTVS-32，菌株ARMTVS-32产量达到了36.8mg/L，与原始出发菌株相比，产量提高了77％。 研究了茄尼醇、对羟基苯甲酸、橘子皮提取物D、胡萝卜提取物E、烟草提取物对ARMTVS-32合成辅酶Q10的影响，结果表明这些物质对菌体合成辅酶Q10有一定促进作用，添加0.2g/L茄尼醇时，辅酶Q10含量提高了17%，达到了40.7mg/L；添加1.2g/L橘子皮提取物D时，辅酶Q10含量提高了13.8%，达到了39.6mg/L；添加0.5g/L胡萝卜提取物E时，辅酶Q10含量提高了25.3% ，达到了43.6mg/L；添加8g/L烟草提取物时，辅酶Q10含量提高了12.6%，达到了39.2mg/L。 Production of Coenzyme- Q10 (CoQ10) by fermentation is considered as a process with broad prospects.Quantitative Analysis of CoQ10 in the culture of microbe by TLC—UV spectrophotometry was developed, by using this method we got the strain Agrobacterium radiobacter,which was isolated from forest soil of southwest of China. The effect of the single factor on CoQ10-production ability of the strain was examined by liquid cultured, and its best optimum cultivation conditions were established by orthogonal method. The results showed that the optimum fermentation conditions were as following: carbon sources glucose 20g/L,sucrose 40g/L; nitrongen sources (NH4)2SO4 10g/L,maize liquid 30g/L;yeast extract 3g; K2HPO4 3g/L,MgSO4.7H2O 1g/L; initial pH was 7 and volume of medium(medium volume vs flask volume) was 50mL/500mL, incubating for 120h on a rotary shaker at 220 rpm and 28℃.Under these conditions, the biomass and CoQ10 concentration reached 50g/L and 20mg/L respectively. According to the biosynthesis mechanism of CoQ10 and breeding theory, CoQ10 over-production strains were screened by UV--NTG. mutation using Agrobacterium radiobacter No.50 as parent strain. A microbe-juice resistant mutant ARMTVS-32, which also could resist tobacco-juice, VK3 and streptomycin, was screened out from an agar plate. The CoQ10 content of ARMTVS-32 reached 36.8mg/L, which was 77% higher than the initial strain. In addition, We discussed the effects of some organic substrates on the synthesis of CoQ10 in ARMTVS-32. The results showed that solanesol, orange juice D, carrot juice E and tobacco juice could promote the CoQ10 accumulation in the cells. The CoQ10 content of ARMTVS-32 reached 40.7mg/L when added 0.2g/L solanesol,it reached 39.6mg/L when added 1.2g/L orange juice D，it reached 43.6mg/L when added 0.5g/L carrot juice E. it reached 39.2mg/L when added 8g/L tobacco juice.

一株掷孢酵母利用红薯淀粉酶解液积累油脂研究

本论文以红薯淀粉的双酶法水解液为碳源，从19 株红色酵母中筛选出一株油脂含量较高的菌株掷孢酵母（Sporobolomyces reseus）As.2.618。为了提高掷孢酵母（S.reseus）As.2.618 的油脂产量，考察了培养基组成对该菌生长情况及油脂积累的影响。用均匀设计法对培养基组成进行了优化，由DPS软件得出的优化结果为：还原糖103g/L、酵母粉11.5g/L、磷酸二氢钾0.3g/L、硫酸镁0.15g/L。生物量可达19.23 g/L,油脂含量为3.875 g/L。研究了添加二价离子对该菌的生长及油脂积累的影响,结果表明Zn2+对该菌生长和油脂积累都有显著促进作用。研究了发酵条件以及添加氧载体正十二烷对该菌发酵的影响，表明添加正十二烷有利用于该菌生长与油脂积累。得出最佳发酵条件是：在还原糖103g/L、酵母粉11.5g/L、磷酸二氢钾0.3g/L、硫酸镁0.15g/L。添加30mg/L 硫酸锌,接种量为5％，在24h 后添加2g/L 的碳酸钙和2%(v/v)正十二烷，pH6.0 培养温度为27℃，转速为200r/min，培养时间为7 天的条件下，该菌生物量干重可达35.05g/L,油脂含量也达11.98g/L。Lipid is one of the basic material for life-sustaining activities andimportant industrial materials. As lipid resources mainly come from the animal andthe plant, the problem of lipid lack is encountered at times. The lipid frommicroorganisms is the substitute and superior to the above lipid with a short period ofproduction and much cheaper fermentation materials such as agricultural and sidelineproducts or wastes of crop.Thus large scale production and broad application ofmicrobial lipid will be efficient not only in substitute of the animal and the plant lipidfor food and industrial field , but also inducing a new way leading to solve the energyproblem.For the purpose of exploring the characteristics of lipid production of redyeasts from sweet potato starch hydrolysates. 19 red yeasts are screened for thecapability of lipid producing and one strain Sporobolomyces reseus As.2.618 withsuperior performance is sellected.To improve the Sporobolomyces reseus As.2.618’s capability of lipidaccumulation , the components of the medium, which may influence the growth of thestrain and the lipid yield have been studied. To get the optimum mediumcomponents ,the “uniform design” was used .The DPS software gave the optimummedium component is: reducing sugar 103 g/L、yeast extract 11.5 g/L、KH2PO4 0.3g/L、MgSO4 0.15 g/L. The biomass could reach up to 19.23 g/L and lipid yield 3.87g/L with the above composition of fermentation medium.Furthermore the fermentation conditions , addition of the divalent metal ionsand the oxygen vector to increase the strain’s lipid producing capability are tested.The optimum condition is : reducing sugar 103 g/L、yeast extract 11.5 g/L、KH2PO40.3 g/L、MgSO4 0.15 g/L，Adding 30mg/L ZnSO4,and adding 2g/L CaCO3 2％(v/v)n-dodecane after 24h’s fermentation. the optimal fermentation condition were asfollow :30ml medium in the 500ml flask with initial pH 6.0,the flasks with 5%inoculation volume were at 200r/min shaking speed for 7d’s fermentation at27 .Under this kind of condition the high biom ¡æ ass which reach to 35.05 g/L could begot ,the yield of lipid also could reach to 11.98g/L.

两株耐碱性木聚糖酶产生菌的筛选及产酶条件研究

本文主要研究了从造纸厂碱性土壤中筛选得到的，能够产生耐碱木聚糖酶的两株放线菌X24-14和X15-17。通过16 S rRNA基因序列分析并结合菌株的形态特征以及生理生化特性，初步认为菌株X15-17为拟诺卡氏菌属（Nocardiopsis）的一个潜在新种；菌株X24-14为纤维化纤维菌（Cellulosimicrobium cellulans）。 在此基础上探索了菌株X24-14和菌株X15-17所产木聚糖酶的基本酶学性质。研究发现，两株菌所产的木聚糖酶的耐碱性均较强： 1）菌株X24-14所产的木聚糖酶，在pH 4.2～9.4的范围内能维持较高的活力，pH 9.4条件下，仍能保持80％的酶活力；2）菌株X15-17所产的木聚糖酶在pH 4.0～9.0的范围内能维持较高的活力，pH 9.0条件下，仍能保持80％的酶活力；3）两株菌所产的木聚糖酶均具有较好的pH稳定性，在pH 2.0～11.0范围内稳定，pH 11.0、4 ℃条件下处理24 h仍具有75％的活力。 本文还重点研究了菌株X24-14在不同培养基成分及不同培养条件下的产酶情况，确定了其适宜的产酶条件。结果显示，菌株X24-14的最适碳源为麸皮；最适氮源为蛋白胨；最适产酶pH为pH 8.5。菌株X24-14适宜的产酶条件为：麸皮60 g/L，蛋白胨10 g/L，K2HPO4 7.0 g/L，pH 8.5，接种量为5％，37 ℃，200 r/min发酵培养108 h。 Two strains of actinomycetes, X24-14 and X15-17, which produced alkali-tolerant xylanase were screened from the soil samples collected from a pulp mill in china. Based on the morphological, physiochemical characteristics and 16S rRNA sequence, X24-14 was priminarily identified as cellulosimicrobium cellulans ; X15-17 was priminarily identified as a new species of Nocardiopsis. The investigation examined the enzyme activities which produced by X24-14 and X15-17 under different pH and different temperatures. The results showed that : 1）The xylanase from X24-14 had characteristic of alkali-tolerance: It remains 80% relative activity at pH ranges between pH 4.2 and pH 9.4 under 50℃. 2)The xylanase from X15-17 also showed characteristic of alkali-tolerance, it remains 80% relative activity at pH ranges between pH 4.0and pH 9.0 under 50℃. 3）The xylanase from the two strains showed alkali-stable characteristics. They were stable at pH ranges between pH 2.0 and pH 11.0, showing 75% of its maximal activity remaining under 24 hours of treatment at 4℃. We also studied the effect of different growth conditions: carbon source, nitrogen sources, inoculum size, and initial pH on the production of xylanase of strain X24-14. The results showed that :The optimal carbon source was wheat bran; The optima nitrogen source was peptone; The maximum xylanase activity was achieved in the medium containing 60 g/L wheat bran, 10 g/L peptone, 7 g/L K2HPO4, inoculum size 5% and pH 8.5, under 37℃ in 108 h.

微生物酶法拆分消旋芳香族氨基酸的研究

通过单因子和多因子摇瓶正交试验，确定了米曲霉液态发酵产氨基酰化酶的最佳发酵条件。优化发酵培养基组成（ρ/g L-1）： 葡萄糖40,蔗糖10,可溶性淀粉20,蛋白胨2.5,马铃薯液1 000mL, pH自然。培养基装量50mL/250mL三角瓶，接种量4%。培养温度30℃，转速100 rmin-1，发酵时间42h。每50mL培养物的总酶活由优化前的2627U提高到7338U，是优化前的2.79倍。 研究了米曲霉氨基酰化酶的部分酶学性质，该酶催化反应的最适pH为7.0，最适温度为40℃，低浓度的Co2+（5×10-4mol/L）对酶活激活作用显著，催化反应过程中，底物浓度大于0.2 mol/L时，存在高浓度底物抑制酶活力现象。 初步探索了包埋法固定化米曲霉氨基酰化酶的载体，在实验的五种载体中，以海藻酸钠为载体包埋固定化米曲霉氨基酰化酶酶活保留率高，且操作简单，成本低廉。对包埋法固定化米曲霉氨基酰化酶酶学性质进行了研究，较游离米曲霉氨基酰化酶，最适温度未发生改变，最适pH向碱性范围偏移至8.0，对酸碱和热的稳定性增强，最适底物浓度增大到0.4 mol/L。 根据氨基酰化酶能立体专一水解L-氨基酰化物的特点，利用米曲霉氨基酰化酶对消旋苯丙氨酸进行了拆分。在米曲霉氨基酰化酶选择性的作用于底物N-乙酰-L-苯丙氨酸，得到L-苯丙氨酸后，通过732阳离子树脂和结晶法分别将L-苯丙氨酸和N-乙酰-D-苯丙氨酸分离，N-乙酰-D-苯丙氨酸通过酸水解脱去乙酰基得到D-苯丙氨酸，拆分得到光学纯度为98%的L-苯丙氨酸（收率84.8%）和光学纯度为92.3%的D-苯丙氨酸（收率89.5%）。 separate factors tests and orthogonal experiments,the optimum fermentation conditions of aminoacylase –producing Aspergillus oryzae were determined, as follows（ρ/g L-1）,glucose 40,sucrose 10,soluble starch 20,peptone 2.5，potato juice 1000ml, inoculation volume 4%and fermentation temperature 30℃,rotation speed 100rmin-1.The highest total enzyme activity ,7338μ,was obtained after fermentation for 42 h, increased by 279% compared with the original value of 2627μbefore optimization. We dicussed partial characteristics of aminoacylase. The optimal pH and temperature of aminoacylase were 7.0 and 40℃ respectively. Low- concentration Co2+ (5×10-4mol/L）activated the aminoacylase remarkably while high-concentration substrate lowered the aminoacylase . Five vectors has been used for immobolizing the enzyme and calcium alginate showed to be the best one for it had the slightest influence on the enzyme activity, easy to operate ,and low in price, comparing with other fours. The enzymatic charateristic study showed that its optimum temperature didn’t change, but the optimum pH and substrat concentration were higher after immobilization. The stability of immobolized enzyme to acid, alkaline and heat rised as well. The aminoacylse from Aspergillus oryzae was used to resolute racemic phenylalanine to obtain D-phenylalanine. After catalyzing process, we took two methods to separate D-phenylalanine .In end,L-phenylalanine was obtained with 98% optical purity in 84.8% yield, D-phenylalanine was obtained with 92.3% optical purity in 89.5% yield.

功能菌剂的混合发酵研究

随着化工行业的发展，大量有毒有害难降解有机物随工业废水的排放进入环境，这些物质能够在环境中长期存在、积累和扩散，通过食物链对动植物的生存及人类的健康造成不良影响。本文以苯酚、对氯硝基苯、氯苯和十六烷为模拟污染物，以前期研制的功能菌剂为对象，经过紫外线线诱变筛选出优于出发菌株的功能菌，对诱变后功能菌的理化性能进行了研究，对菌种进行了鉴定，在此基础上，就其相互之间的微生态关系进行研究，为混合发酵提供理论基础，并就其最佳发酵条件及发酵参数进行了研究，最后对发酵产品的性能进行了检测。目前，国内外有关功能菌剂的研究还存在多方面的不足，主要包括：①由于多菌种混合发酵过程较为复杂，各菌之间存在复杂的相互作用，影响因素较多，关于菌种之间的相互关系研究得很少，环境功能菌剂的发酵方法大多采用单独发酵后混合的方式。单独发酵对原材料、设备和能源的利用率较低，对于多菌种制剂发酵，在设备、能源和原材料的方面造成的浪费更大，将会大幅增加菌剂的生产成本，影响多菌种功能菌剂的发展；②功能菌剂生产过程的质量控制方面研究得较少；③功能菌剂产品的稳定性、抗冲击性能研究得较少，对环境微生物制剂的研究主要集中在菌种选育和培养条件优化方面。 通过本论文研究，得到以下主要结论。 （1）在紫外线诱变处理中，用紫外线对发生一定程度退化的出发菌株进行诱变处理后，六株具有高效降解性能的菌株被筛选出来，诱变筛选出的菌株形态和ERIC-PCR指纹图谱与出发菌株相比发生了明显改变；而且诱变后的菌株对目标难降解底物的降解能力均得到改善，其中，FPN、FCB、F14、FEm对目标底物的降解率提高了20%以上；诱变后菌株经过7次连续传代接种后，对目标难降解底物的降解率无显著变化，具有一定的遗传稳定性。并对诱变后的功能菌进行了初步的鉴定，这6株菌都分别是芽孢杆菌。 （2）对诱变后的功能菌相互之间的微生态关系进行了研究，通过抑菌实验、生长量以及基质消耗量的比较，确定它们之间的生长关系是无害共栖关系，可以进行混合发酵。 （3）对该功能菌剂进行发酵培养条件研究，结果表明发酵培养基的最佳成分（g/L）：葡萄糖 31.0g/L、玉米粉10.0g/L、磷酸氢二钾1.0g/L、硫酸铵1.1g/L、硫酸镁0.55g/L。通过研究不同的培养条件对菌体生长和降解性能的影响，确定了最佳培养条件：培养基初始pH7.5；最适温度32℃；培养基装液量125mL（250 mL三角瓶），以及培养时间对降解性能的影响，培养20 h的产物对降解最为有利。通过研究添加不同目标污染物对菌体生长和降解性能的影响，确定了添加目标污染物的最佳量以及最佳时间：苯酚投加量：1.125 g/L，对氯硝基苯投加量：0.1 g/L；最佳投加时间为发酵培养开始后4 h。 （4）以摇瓶分批发酵最优条件为基础，对FPN、F10、FCB、FNa、F14 和 FEm进行了摇瓶分批发酵试验。以摇瓶分批发酵试验数据为依据，对功能菌剂分批发酵动力学进行了研究，建立了菌体生长和基质消耗的动力学模型，拟合模型能较好的反映功能菌剂分批发酵过程。 （5）功能菌剂和活性污泥协同作用，可以提高系统的生物降解能力，功能菌剂投加量为2%，新鲜活性污泥3500 mg/L，降解24 h条件下，功能菌剂和活性污泥的协同作用对COD的去除率和对照组相比，最多的提高了36.8%。功能菌剂和活性污泥协同作用以及活性污泥的单独作用，其生物降解过程均符合一级反应动力学过程，功能菌剂和活性污泥协同作用的生物降解动力学方程为：，相关系数97%。采用SBR运行方式，引入功能菌剂的SBR系统明显能够改善和提高生物降解的效率。与仅有活性污泥的系统相比，系统对COD的平均去除率可以提高27.1%，同时，系统的耐负荷冲击以及耐毒害冲击的性能比仅有活性污泥的SBR系统强，特别是负荷冲击对引入功能菌剂的SBR系统影响很小。仅有活性污泥的SBR系统经过负荷冲击和毒害冲击之后，不能恢复到冲击之前的水平，而且系统有效作用时间的周期比引入功能菌剂的SBR系统相比大大缩短，而引入功能菌剂的SBR系统处理效果较为稳定，恢复能力很强。 Along with the development of industries, many recalcitrant organic chemicals have been discharged into natural environments together with wastewaters and can exist in waters, soil and sediments for a long time without degradation. These haz-ardous substances, their byporducts and metabolizabilities can be highly toxic, mu-tagenic and carcinogenic, thereby threatening animals, plants and human health through food chain. Consequently the removal of these compounds is of significant interest in the area of wastewater treatment. In this dissertation, the phenol, hydro-quinone, chlorobenzene and hexadecane treated as the model pollutants, the func-tional microorganism agent was used as the starting strains, they treated with ultra-violet light, and then the mutant strains with high degradation ability were screened out and identified primarily, the relationship between these stains were studied, the medium composition and fermentation conditions were optimized, the degradation ability of the fermented production was tested. The literature survey indicates that the study of the microorganism agent is far from complete and more information is re-quired on following problems. 1, Because of the complexity of relationship in mixed fermentation and the complicated factors, the study is hardly to process.2, There is a lack of information on the quality control of the producing process .3, And there is a lack of information on the stability about the microorganism agent. In this dissertation, the main results of the present study could be summarized as follows: (1)The degenerate starting strains were treated with the ultraviolet light, and six mutant strains with high biodegradation ability were screened out by using the me-dium with selective pressure of model pollutants. The mutant strains had great changes in colonialmorphology and ERIC-PCR fingerprinting. And the mutant strains got obvious advantages over the starting strains in degradation ability and over 20% improvement of removal rates was achieved for FPN、FCB、F14 and FEm. The de-gradation ability of the mutant strains was stable after seven generations. After that, the mutant strains were primarily identified as bacillus respectively. (2) The relationship between these mutant strains was studied. By the compari-son of antibiosis effect, biomass and consumption of substrate, the relationships were neutralism and they could be mixed fermented. (3) The optimized cultivation conditions were as follows: glucose 31.0 g/L, corn power 10 g/L, K2HPO4 1.0 g/L, (NH4)2SO4 1.1 g/L, MgSO4 0.55 g/L, initial pH7.5, temperature 32℃, working volume 125 mL/250 mL, and cultivation time 20h (con-sidering the time effect on degradation ability), adding pollutants phenol (1.125 g/L) and hydroquinone (0.1 g/L) into the broth at 4 h after cultivation. (4) Based on the above optimum condition, the batch fermentation was per-formed with strains FPN, F10, FCB, FNa, F14 and FEm in shake flask. The batch fermentation kinetics was studied based on the experimental data. Two kinetic models were constructed which could reflect the regularity of growth and substrate consump-tion in the process of batch fermentation. (5) The co-operation of functional microorganism agent and activated sludge could raise biodegradation of system by adding some microorganism agent and 3500 mg/L fresh activated sludge. Bioaugumentation by the addition of high effective deg-radation culture enhanced the treatment effect of SBR system and the COD removal rate was increased by 20%-36.8%. Its biodegradation matched first-order dynamical reaction equation, and the reaction equation was ln0.2327.391ct=−+. The micro-organism agent had the effect of optimization to activated sludge micro-ecosystem. The SBR system adding 2% microorganism agent, the average COD removal rate of that was increased by 27.1% and stronger anti-shock ability to load and toxicant were achieved (compared with SBR system just adding activated sludge). Especially the load-shock has barely effect to the SBR system adding microorganism agent. After the load and toxicant shock, the SBR system just adding activated sludge couldn’t come back to original level and the activated sludge micro-ecosystem was frustrated. The applying of microorganism agent increased biological activity and system’s re-sistance ability to load shock and toxicant shock.

克拉维酸产生菌的诱变育种与发酵工艺优化研究

以克拉维酸产生菌棒状链霉菌Streptomyces clavuligerus CCRC11518（ATCC 27064）III50为出发菌株, 首先比较各种物理和化学诱变剂处理对其克拉维酸生物合成的影响, 确定了亚硝基胍为棒状链霉菌诱变育种的诱变剂及其处理剂量: 2mg/ml、40min. 经浓度为2mg/ml的亚硝基胍处理40min后, 采用新颖理性化筛选方法, 通过逐步筛选自身代谢产物抗性突变株、克拉维酸抗性突变株和链霉素抗性突变株, 最终得到一株克拉维酸高产菌VI118(效价633μg/ml), 其克拉维酸效价是出发菌株(效价377μg/ml)的167.9%. 该高产突变株在琼脂斜面培养基上连续传接10代, 克拉维酸效价保持稳定. 通过单因子和多因子摇瓶正交试验, 对高产菌株VI118的发酵条件进行了研究, 确定最佳发酵条件: 甘油60g, 水解植物蛋白 60g, KH2PO4 0.5 g, 玉米浆 7.5g, MnSO4•H2O 0.34g, MgSO4•7H2O 0.99g, FeSO4•7H2O 0.56g, 蒸馏1000ml, pH 7.0, 发酵培养基装量20ml/250ml三角瓶, 接种量10％, 培养温度28ºC, 220r/min摇床培养72h后测定效价. 在最佳发酵条件下克拉维酸效价达到651μg/ml, 同时把初始发酵培养基的昂贵成分替换为廉价的工业原料. 通过摇瓶分批补料试验, 得到最佳补料物质和补料方式：在上述最佳发酵条件下, 分别在发酵培养48h、56h、64h、72h时补加4ml无菌水, 80h发酵结束, 克拉维酸效价达到905μg/ml. 在不增加原料成本的情况下通过摇瓶补料方式克拉维酸效价为未补料的139.0％, 总产量为未补料的264％. By a novel rational screening method, mutant Streptomyces clavuligerus CCRC11518（ATCC 27064）III50（titres 377μg/ml）, as the clavulanic acid-producing parent strain, was treated by NTG (2mg/ml) for 40min, and the self-generated metabolites resistant mark, the clavulanic acid resistant mark and the streptomycin resistant mark were added step by step. Finally, the mutant VI118（titres 633μg/ml）with the three marks was obtained. The clavulanic acid productivity of this mutant was increased by 167.9% compared with the parent strain. After reproducing 10 generations on the agar medium slant, the productivity of this mutant was stable. The optimum fermentation conditions were established as followings: glycerol 60g, acid hydrolyzed vegetable protein 60g, KH2PO4 0.5g, corn steep liquor 7.5g, MnSO4•H2O 0.34g, MgSO4•7H2O 0.99g, FeSO4•7H2O 0.56g, distilled water 1 liter, pH 7.0, 20ml in 250ml shake-flask, inoculation 10%(v/v), fermentation temperature 28ºC, rotation speed 220 r/min, time 72h. The clavulanic acid productivity was 651μg/ml, while used the low-priced industrial raw materials. After studying on fed-batch in the shake-flask, the optimum fed-batch manner was obtained: under optimum fermentation conditions, at 48h, 56h, 64h and 72h, adding 4ml distilled water into each flask, fermentation ending at 80h. The clavulanic acid productivity was increased by 139% compared with no fed-batch, meanwhile the total yield was increased by 264%.

重离子辐照粘红酵母诱变育种及其产油条件的优化

本论文以在微生物油脂生产中较具潜力的粘红酵母为材料，利用兰州近代物理研究所重离子研究装置（HIRFL）产生的80 MeV/u碳离子束对产油菌株粘红酵母进行辐照诱变, 采用含有脂肪酸合成酶抑制剂cerulenin的培养基进行高产油脂突变株的初选, 并通过磷酸香草醛反应和氯仿甲醇抽提法对初筛菌株油脂含量进行分析，复选出油脂产量和质量都有较大提高的突变菌株，并对其产油条件进行优化，以期获得一些其它诱变方法难以获得的高产油脂微生物突变株，大力开发离子束辐照技术在解决能源危机中的应用。通过本论文的实验研究，得到了以下初步结果 ： 1．液体培养基中，粘红酵母菌在接种后的40h－80h处于对数生长期，此时菌体的生长繁殖比较旺盛，活力最佳，为辐照诱变的最适时期。辐照后，不同来源的菌株对重离子辐射的敏感性有所不同，然而其存活趋势却大致相当。菌体的存活率都呈现出随辐照剂量的增加先减小后增加，再减小的马鞍型剂量－效应曲线。 2．cerulenin对酵母细胞的生长具有较好的抑制作用，浓度为8.96×10-6 mol/L时，抑制率达98%以上，可作为高产油脂粘红酵母菌的筛选浓度。通过磷酸香草醛反应法和氯仿－甲醇抽提法对初筛菌体油脂含量进行定量分析，结果表明初筛菌株的正突变率达66%以上。该方法快速方便，是一种较为理想的高产油脂酵母菌的筛选方法。通过这些方法，筛选出了2株油脂含量明显高于对照的突变株。 3．经实验发现，菌体培养物与磷酸香草醛试剂反应后在530nm的光吸收与氯仿－甲醇抽提法所测得的菌体油脂含量成正比，其标准曲线方程为y=38.2257x+0.67314，R2为0.995，从而建立起一种方便快捷的油脂定量测量方法，有望实现自动化分析。 4．通过对影响粘红酵母菌生长和油脂合成的几个主要因素(葡萄糖浓度、碳氮比、接种量、培养时间、温度、PH值)的初步探讨研究，得出了粘红酵母突变株的最佳产脂条件为: 葡萄糖浓度10％，碳氮比40:1，接种量10%，温度28℃，PH=5.0，培养时间为6天

Visualization of dust explosion under microgravity conditions

The objective of this work was to apply visualization methods to the experimental study of cornstarch dust-air mixture combustion in a closed vessel volume under microgravity conditions. A dispersion system with a small scale of turbulence was used in the experiments. A gas igniter initiated combustion of the dust-air mixture in the central or top part of the vessel. Flame propagation through the quiescent mixture was recorded by a high-speed video camera. Experiments showed a very irregular flame front and irregular distribution of the regions with local reactions of re-burning behind the flame front. at a later stage of combustion. Heat transfer from the hot combustion products to the walls is shown to have an important role in the combustion development. The maximum pressure and maximum rate of pressure rise were higher for flame propagation from the vessel center than for flame developed from the top pan of the vessel. The reason for smaller increase of the rate of pressure rise, for the flame developed from the top of the vessel. in comparison with that developed from the vessel center, was much faster increase of the contact surface of the combustion gases with the vessel walls. It was found that in dust flames only small part of hear was released at the flame front, the remaining part being released far behind it.

Magnetron Sputtering Growth of InAs0.3Sb0.7 Films on (100) GaAs Substrates: Strong Effect of Growth Conditions on Film Structure

The growth of highly lattice-mismatched InAs0.3Sb0.7 films on (100) GaAs Substrates by magnetron Sputtering has been investigated and even epitaxial lnAs(0.3)Sb(0.7) films have been successfully obtained. A strong effect of the growth conditions on the film structure was observed, revealing that there was a growth mechanism transition from three-dimensional nucleation growth to epitaxial layer-by-layer growth mode when increasing the substrate temperature. A qualitative explanation for that transition was proposed and the critical conditions for the epitaxial layer-by-layer growth mode were also discussed.

Influence of the Processing Conditions on the Characteristics of the Clad Layers Produced with Laminar Plasma Technology

Laminar plasma technology was used to produce ceramic hardened layers of Al2O3-40% mass Ni composite powders on stainless steel substrates. In order to investigate the influences of processing conditions on the morphologies of the surface modified layers, two different powder-feeding methods were tested, one with carrier gas called the powder injection method, and the other without carrier gas called powder transfers method. The microscopic investigations demonstrate that the cross-section of the clad layers consists of two distinct microstructural regions, in which the Al2O3 phases exhibit different growth mechanisms. When the powder transfers method is adopted, the number density and volume fraction of the Al2O3 particles increase considerably and their distributions exhibit zonal periodical characteristics. When the powder-feeding rate increases, the microstructure of the Al2O3 phases changes from a small globular to a long needle shape. Finite element simulations show that the transient thermo-physical features of the pool substances, such as solidification rate and cooling rate, influence strongly the mechanisms of the nucleation and the directional growth of the Al2O3 phases in the thermal processing.

Determination of Proper Processing Conditions of Material Surface Heat Treatment Through Finite Element Method

A two-dimensional model has been developed based on the experimental results of stainless steel remelting with the laminar plasma technology to investigate the transient thermo-physical characteristics of the melt pool liquids. The influence of the temperature field, temperature gradient, solidification rate and cooling rate on the processing conditions has been investigated numerically. Not only have the appropriate processing conditions been determined according to the calculations, but also they have been predicted with a criterion established based on the concept of equivalent temperature area density (ETAD) that is actually a function of the processing parameters and material properties. The comparison between the resulting conditions shows that the ETAD method can better predict the optimum condition.

Concentration distribution in solution crystal growth: effect of moving interface conditions

The linear diffusion-reaction theory with finite interface kinetics is employed to describe the dissolution and the growth processes. The results show that it is imperative to consider the effect of the moving interfaces on the concentration distribution at the growth interface for some cases. For small aspect ratio and small gravity magnitude, the dissolution and the growth interfaces must be treated as the moving boundaries within an angle range of 0 degrees < gamma < 50 degrees in this work. For large aspect ratio or large gravity magnitude, the effect of the moving interfaces on the concentration distribution at the growth interface can be neglected except for gamma < - 50 degrees.

Experimental study on two-phase gas-liquid flow patterns at normal and reduced gravity conditions

Experimental studies have been performed for horizontal two-phase air-water flows at normal and reduced gravity conditions in a square cross-section channel. The experiments at reduced gravity are conducted on board the Russian IL-76 reduced gravity airplane. Four flow patterns, namely bubble, slug, slug-annular transition and annular flows, are observed depending on the liquid and gas superficial velocities at both conditions. Semi-theoretical Weber number model is developed to include the shape influence on the slug-annular transition. It is shown that its prediction is in reasonable agreement with the experimental slug-annular transition under both conditions. For the case of two-phase gas-liquid flow with large value of the Froude number, the drift-flux model can predict well the observed boundary between bubble and slug flows.