FACTORS INFLUENCING CHLOROPHYLL A CONCENTRATION IN THE YANGTZE-CONNECTED LAKES

To determine the environmental factors influencing C, phytoplankton chlorophyll a (Ch1 a), field investigations 4 were conducted in three river-connected lakes (Dongting Lake, Poyang Lake and Shijiu Lake) of the Yangtze floodplain in 2004. Results showed that the average Chi a concentration in these lakes ranged from 2.98 to 3.65 mg m(-3). The major factors influencing Chl a in lentic and lotic regions were total phosphorus (TP) and water velocity (U), respectively. Multiple relationships including total nitrogen (log(10)TN) and water depth (log(10)Z) were established. Further analyses found that the absolute Chi a and slope of log(10)Chl a=f (log(10)TP) in the river-connected lakes were obviously lower than those in the river-isolated lakes. This suggests the river-lake connectivity can significantly modify relationship between TP and chlorophyll a concentration.

Research on various factors influencing the moisture absorption property of sodium polyacrylate

Sodium polyacrylate was synthesized with acrylic acid as the monomer, and sodium bisulfate and ammonium persulfate as the initiator, by means of aqueous solution polymerization. The factors influencing the properties of moisture absorption, such as monomer concentration, dosage of initiator, and reaction temperature were systematically investigated. The experimental results indicate that the moisture-absorbing property of this polymer was better than other traditional material, such as silica gel, and molecular sieve. The best reaction condition and formula are based on the orthogonal experiment design. The optimum moisture absorbency of sodium polyacrylate reaches 1.01 g/g. The mathematical correlation of this polymer with various factors and moisture absorbency is obtained based on the multiple regression analysis. The moisture content intuitive analysis table shows that neutralization degree has the most significant influence on moisture absorbency, followed by monomer concentration and reaction temperature, while other factors have less influence.

Factors influencing the climatological mixed layer depth in the South China Sea: numerical simulations

The mixed layer depth (MLD) in the upper ocean is an important physical parameter for describing the upper ocean mixed layer. We analyzed several major factors influencing the climatological mixed layer depth (CMLD), and established a numerical simulation in the South China Sea (SCS) using the Regional Ocean Model System (ROMS) with a high-resolution (1/12A degrees x1/12A degrees) grid nesting method and 50 vertical layers. Several ideal numerical experiments were tested by modifying the existing sea surface boundary conditions. Especially, we analyzed the sensitivity of the results simulated for the CMLD with factors of sea surface wind stress (SSWS), sea surface net heat flux (SSNHF), and the difference between evaporation and precipitation (DEP). The result shows that of the three factors that change the depth of the CMLD, SSWS is in the first place, when ignoring the impact of SSWS, CMLD will change by 26% on average, and its effect is always to deepen the CMLD; the next comes SSNHF (13%) for deepening the CMLD in October to January and shallowing the CMLD in February to September; and the DEP comes in the third (only 2%). Moreover, we analyzed the temporal and spatial characteristics of CMLD and compared the simulation result with the ARGO observational data. The results indicate that ROMS is applicable for studying CMLD in the SCS area.

Factors influencing hemolytic activity of venom from the jellyfish Rhopilema esculentum Kishinouye

In this study, hemolytic activity of venom from the jellyfish Rhopilema esculentum Kishinouye and some factors affecting it were assayed. The HU50 of R. esculentum full venom (RFV) against chicken erythrocytes was 3.40 mu g/ml and a Hill coefficient value was 1.73 suggesting at least two molecules participated in hemolytic activity. The hemolytic activity of RFV was affected by some chemical and physical factors such as divalent cations, EDTA, (NH4)(2)SO4, pH and temperature. In the presence of Mg2+, Cu2+, Zn2+, Fe2+, Ca2+ ( >= 2 mM), Mn2+ (>= 1 mM), EDTA (>= 2 mM) and (NH4)(2)SO4, the hemolytic activity of RFV was reduced. RFV had strong hemolytic activity at the pH 6-10 and the hemolytic ratios were 0.95-1.19. Hemolytic activity was temperature-sensitive and when RFV was pre-incubated at temperatures over 40 degrees C, it was sharply reduced. (c) 2007 Elsevier Ltd. All rights reserved.

Factors influencing the catalytic activity of SBA-15-supported copper nanoparticles in CO oxidation

Copper nanoparticles were deposited onto mesoporous SBA-15 support via two different routes: post-grafting method and incipient wet impregnation method. Both XRD and TEM reveal that the post-grafting can make Cu particles very small in size and highly dispersed into channels of SBA-15, while the impregnation method mainly forms large Cu particles on the external surface of SBA-15. TPR experiments show that CuO species formed by the post-grafting method is more reducible than that prepared by the impregnation method. The catalytic activity tests for CO oxidation manifests that the sample prepared by the post-grafting method has a much higher activity than that prepared by the impregnation method, with a lowering of 50 degrees C for T-50, showing a strong dependence of catalytic activity on the size and dispersion of Cu particles. Besides the preparation procedure, other factors including calcination temperature, reduction treatment, copper loading as well as the feed composition, have an important effect on the catalytic activity. The best performance was obtained when the catalyst was calcined at 500 degrees C and reduced at 550 degrees C. The calcination and reduction treatment at high temperature have been found to be necessary to completely remove the organic residue and to generate active metallic copper particles. (c) 2005 Elsevier B.V. All rights reserved.

影响纳米压入测试结果的因素

纳米硬度计,又称深度测量压入仪.该仪器在刚性压针上施加特定载荷,同时记录压入试样深度.此技术广泛应用于微纳米尺度力学性能的研究.以MTS Nano Indenter○ RXP为测试手段,参考试样熔融硅为研究对象,进行了不同压入深度的测试.结果显示,硬度和模量有随压入深度减小而增大的趋势.分析了接触零点的确定、压针尖端缺陷、试样表面的吸湿和粗糙度、弹塑性转变等因素对测试结果的影响.在压入深度为微米和亚微米量级时,上述因素对测试结果无显著影响;而在纳米量级时,有显著影响.所以,当压入深度为几十纳米时,纳米压入测试结果的可靠性值得注意.

Influences of slope gradient on soil erosion

The main factors influencing soil erosion include the net rain excess, the water depth, the velocity, the shear stress of overland flows, and the erosion-resisting capacity of soil. The laws of these factors varying with the slope gradient were investigated by using the kinematic wave theory. Furthermore, the critical slope gradient of erosion was driven. The analysis shows that the critical slope gradient of soil erosion is dependent on grain size, soil bulk density, surface roughness, runoff length, net rain excess, and the friction coefficient of soil, etc. The critical slope gradient has been estimated theoretically with its range between 41.5 degrees similar to 50 degrees.