顺丁橡胶浓溶液流变性质与结构参数及△ML,△∑ML的关系

用RheotestⅡ型旋转粘度计,研究了Li,Co,Ni系顺丁橡胶浓溶液的流变性质与结构参数及ΔML,Δ∑ML的关系。在没有凝胶的情况下,Co系顺丁橡胶浓溶液流变行为的非牛顿性显著;Δ∑ML/ML值越大,该胶的支化程度越明显。

An efficient methodology for cryopreservation of spermatozoa of red seabream, Pagrus major, with 2-mL cryovials

The aim of this study was to optimize the cryopreservation protocols for the sperm of red seabream, Pagrus major. The 2-mL cryovials and programmable freezer were employed for cryopreservation. Six extenders, six cryoprotectants in various concentrations ranging from 6 to 20% (v/v), four cooling rates, and three thawing temperatures were evaluated by postthaw sperm motility and fertility. The ratio of sperm to egg for postthaw sperm fertilization trials was experimentally standardized and was optimal at 500:1. The best motility of postthaw sperm (79.4 +/- 4.7% to 88.6 +/- 8.0%), fertilization rates (89.6 +/- 2.9 to 95.6 +/- 1.9%), and hatching rates (85.3 +/- 5.1% to 91.4 +/- 4.3%) were achieved when Cortland extender, dimethyl sulfoxide (15, 18, and 20%) or ethylene glycol (9, 12%) as cryoprotectants, 20 C/min as the cooling rate, and 40 C as the thawing temperature were employed. Moreover, the results on embryonic development were not significantly different between cryopreserved sperm and fresh sperm during incubation process. In conclusion, these methods of cryopreservation of red seabream sperm are suitable for routine aquaculture application and preservation of genetic resources.

抗SARS人源单链抗体H12的表达及复性

从SARS免疫抗体库获得的一株抗SARS-CoV人源单链抗体H12,亟待鉴定.为了快速制备大量具有生物活性的单链抗体H12,构建了pET28a-H12原核高表达载体,表达量占菌体总蛋白质30%以上.采用稀释复性和分子筛柱复性两种方法对包涵体蛋白进行复性与纯化,结果显示两种方法都能使得单链抗体复性.与稀释复性法相比,柱复性效果更好,其抗原结合活性是稀释复性法的1.51倍.柱复性后的单链抗体亲和力测定的解离常数Kd为73.5nmol/mL.为进一步研究单链抗体H12的功能奠定了基础.

Grain Refinement at the Nanoscale Via Mechanical Twinning and Dislocation Interaction in a Nickel-Based Alloy

A nanostructured surface layer was formed on an Inconel 600 plate by subjecting it to surface mechanical attrition treatment at room temperature. Transmission electron microscopy and high-resolution transmission electron microscopy of the treated surface layer were carried out to reveal the underlying grain refinement mechanism. Experimental observations showed that the strain-induced nanocrystallization in the current sample occurred via formation of mechanical microtwins and subsequent interaction of the microtwins with dislocations in the surface layer. The development of high-density dislocation arrays inside the twin-matrix lamellae provides precursors for grain boundaries that subdivide the nanometer-thick lamellae into equiaxed, nanometer-sized grains with random orientations.

Optimal bounded control of first-passage failure of quasi-integrable Hamiltonian systems with wide-band random excitation

The optimal bounded control of quasi-integrable Hamiltonian systems with wide-band random excitation for minimizing their first-passage failure is investigated. First, a stochastic averaging method for multi-degrees-of-freedom (MDOF) strongly nonlinear quasi-integrable Hamiltonian systems with wide-band stationary random excitations using generalized harmonic functions is proposed. Then, the dynamical programming equations and their associated boundary and final time conditions for the control problems of maximizinig reliability and maximizing mean first-passage time are formulated based on the averaged It$\ddot{\rm o}$ equations by applying the dynamical programming principle. The optimal control law is derived from the dynamical programming equations and control constraints. The relationship between the dynamical programming equations and the backward Kolmogorov equation for the conditional reliability function and the Pontryagin equation for the conditional mean first-passage time of optimally controlled system is discussed. Finally, the conditional reliability function, the conditional probability density and mean of first-passage time of an optimally controlled system are obtained by solving the backward Kolmogorov equation and Pontryagin equation. The application of the proposed procedure and effectiveness of control strategy are illustrated with an example.

Investigation on Depth of Heat Affected Zone of Discharge Spot by High Repetitive Rate YAG Laser-Induced Discharge Texturing

It is known that the press formability and the elongation of laser textured sheet are improved, and the service life of textured roll is longer than that of the un-textured roll due to hardening of the treated surface. One of the goals to develop high repetitive rate YAG laser-induced discharge texturing (LIDT) is to get deeper hardening zone. By observing and measuring cross-section of LIDT spots in different discharge conditions, it is found that the single-crater, which is formed by the discharge conditions of anode, which is covered by an oil film and with rectangular current waveform, has the most depth of heat affected zone (HAZ) comparing with other crater shapes when discharge energy is the same. The depth of HAZ is mainly depends on pulse duration when the discharge spot is single-crater. The results are analyzed.

A finite element method for cracked components of structures

In this paper, a method is developed for determining the effective stiffness of the cracked component. The stiffness matrix of the cracked component is integrated into the global stiffness matrix of the finite element model of the global platform for the FE calculation of the structure in any environmental conditions. The stiffness matrix equation of the cracked component is derived by use of the finite variation principle and fracture mechanics. The equivalent parameters defining the element that simulates the cracked component are mathematically presented, and can be easily used for the FE calculation of large scale cracked structures together with any finite element program. The theories developed are validated by both lab tests and numerical calculations, and applied to the evaluation of crack effect on the strength of a fixed platform and a self-elevating drilling rig.

NaCl对液-液扩散法生长溶菌酶晶体的影响

用动态光散射法研究了不同浓度NaCl对液—液扩散法生长溶菌酶晶体的影响，并测量了晶体生长前后体系的Zeta电势．结果表明，NaCl浓度较高时，在溶菌酶溶液—凝胶界面处会发生液液分层现象，溶液中一直存在较大的聚集体，生长出的晶体质量较差．而在合适的NaCl浓度下，随着溶液Zeta电势降低，溶液中溶菌酶的大的聚集体发生解聚集，生长出的晶体质量较高．

牛血清蛋白在亲水硅片表面吸附的原子力显微成像

本文用原子力显微术（AFM）研究了牛血清白蛋白（BSA）在亲水硅片表面的吸附，硅片表面经亲水处理后，将牛血清蛋白（BSA）吸附在表面，采用轻敲模式，可获得清晰的AFM图像，牛血清蛋白（BSA）的AFM图像表明：BSA在亲水硅片表面是单分子，水平吸附在硅片表面，且吸颗粒状；1mg/ml的BSA在吸附30min后为饱和吸附。BSA到达硅表面后，蛋白中可移动的带正电荷的基团可以趋向亲水表面，使BSA与硅表面的静电相互作用由斥力变为吸引力，BSA可以稳定地吸附在亲水硅片表面。

Application of Optical Protein-chip in Detecting Phage M13KO7

Abstract: Avidin layer was bound on the substrate surface of Silicon wafer modified with aldehyde. The interaction between avidin and biotin was adopted for the immobilization of mouse monoclonal biotin-anti-M13 (antibody GP3)-labeled biotin. The surface was incubated in a solution containing phage M13KO7, which was trapped by the antibody GP3 with the interaction between phage M13KO7 and antibody GP3, resulting in a variation of layer thickness that was detected by imaging ellipsometry. The results showed a saturated layer of antibody GP3 with a thickness about 6.9 nm on the surface of the silicon wafer. The specific interaction between phage M13KO7 and antibody GP3 resulted in a variation of layer thickness. The layer of phage M13KO7 bound with antibody GP3 was 17.5 nm in the concentration of 1.1×1010 pfu/mL. Each variation of the layer thickness corresponded to a concentration of phage M13KO7 in the range of 0.1×1010–2.5×1010 pfu/mL, with the sensitivity of 109 pfu/mL. Compared with other methods, the optical protein-chip, requiring only short measurement time, label free, is a quantitative test, and can be visualized. This study could be significant on the interactions between the antibody and the virus, showing potential in the early diagnosis of virosis.