Void swelling in MA956 ODS steel irradiated with 122 MeV Ne-ions at elevated temperatures

An investigation of a commercial oxide dispersion-strengthened steel (MA9561) irradiated with high energy Ne-ions to high doses at elevated temperatures is presented. Specimens of MA956 oxide dispersion strengthened steel together with a 9% Cr ferritic/martensitic steel, e.g., Grade 92 steel were irradiated simultaneously with 20Ne-ions (with 122 MeV) to successively increasing damage levels of 1, 5 and 10 dpa at the damage peak at 440 C and 570 C, respectively. Cross-sectional microstructures of the specimens were investigated with transmission electron microscopy. MA956 oxide dispersion strengthened steel showed a higher resistance to void swelling especially to void growth at the grain boundaries than the ferritic/martensitic steel, e.g., Grade 92 steel did, and thus exhibited a prominence for an application in the situation of a high He production at high temperatures. The suppression of the growth of voids especially at the grain boundaries in MA956 is ascribed to an enhanced recombination of the point defects and a trapping of Ne atoms at the interfaces of the yttrium–aluminum oxide particles and the matrix.

Void swelling in a 9Cr ferritic/martensitic steel irradiated with energetic Ne-ions at elevated temperatures

In this work the void swelling behavior of a 9Cr ferritic/martensitic steel irradiated with energetic Ne-ions is studied. Specimens of Grade 92 steel (a 9%Cr ferritic/martensitic steel) were subjected to an irradiation of Ne-20-ions (with 122 MeV) to successively increasing damage levels of 1, 5 and 10 dpa at a damage peak at 440 and 570 degrees C, respectively. And another specimen was irradiated at a temperature ramp condition (high flux condition) with the temperature increasing from 440 up to 630 degrees C during the irradiation. Cross-sectional microstructures were investigated with a transmission electron microscopy (TEM). A high concentration of cavities was observed in the peak damage region in the Grade 92 steel irradiated to 5 dpa, and higher doses. The concentration and mean size of the cavities showed a strong dependence on the dose and irradiation temperature. Enhanced growth of the cavities at the grain boundaries, especially at the grain boundary junctions, was observed. The void swelling behavior in similar 9Cr steels irradiated at different conditions are discussed by using a classic void formation theory. (c) 2008 Elsevier B.V. All rights reserved.

Structural evolution of tensile deformed high-density polyethylene at elevated temperatures: Scanning synchrotron small- and wide-angle X-ray scattering studies

The structural evolution of an ice-quenched high-density polyethylene (HDPE) subjected to uniaxial tensile deformation at elevated temperatures was examined as a function of the imposed strains by means of combined synchrotron small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS) techniques. The data show that when stretching an isotropic sample with the spherulitic structure, intralamellar slipping of crystalline blocks was activated at small deformations, followed by a stress-induced fragmentation and recrystallization process yielding lamellar crystallites with their normal parallel to the stretching direction. Stretching of an isothermally crystallized HDPE sample at 120 degrees C exhibited changes of the SAXS diagram with strain similar to that observed for quenched HDPE elongated at room temperature, implying that the thermal stability of the crystal blocks composing the lamellae is only dependent on the crystallization temperature.

The Influence of Grain Size and Temperature on the mechanical Deformation of Nanocrystalline Materials: Molecular Dynamics Simulation

Nanocrystalline (nc) materials are characterized by a typical grain size of 1-100nm. The uniaxial tensile deformation of computer-generated nc samples, with several average grain sizes ranging from 5.38 to 1.79nm, is simulated by using molecular dynamics with the Finnis-Sinclair potential. The influence of grain size and temperature on the mechanical deformation is studied in this paper. The simulated nc samples show a reverse Hall-Petch effect. Grain boundary sliding and motion, as well as grain rotation are mainly responsible for the plastic deformation. At low temperatures, partial dislocation activities play a minor role during the deformation. This role begins to occur at the strain of 5%, and is progressively remarkable with increasing average grain size. However, at elevated temperatures no dislocation activity is detected, and the diffusion of grain boundaries may come into play.

Combined Effects of Silica Filler and Its Interface in Epoxy Resin

In this paper, mechanical properties of silica-filled epoxy resin are tested. The tests show that at elevated temperatures, the material’s properties (e.g. yield stress, flow stress, etc.) vary immonotonically with filler volume fraction. Nanoindentation test results suggest that an interface region, stronger than the matrix, is formed in the materials. The formation of the interface has positive effects on the yield strengths of materials. The addition of particles in the matrix produces a large disturbance in stress distribution, leading to stress concentration in the matrix. The stress concentration has negative effects on the yield strengths of materials. The calculation demonstrates that the maximum stress in samples varies immonotonically with particulate concentration. So, the immonotonic variation of mechanical behavior of materials may be rooted in the contradictory effects of the interface region and the stress concentration caused by particulate addition.

MOCVD growth and properties of ZnO thin films on LiNbO3 substrates

ZnO thin films were grown on (0001)LiNbO3 substrates by the MOCVD technique. The substrate temperatures during growth were changed from 400 to 600 degrees C. The X-ray diffraction (XRD) pattern of the ZnO film showed a strong [002] reflection peak, and the peak intensity was dependent on substrate temperature. The ZnO columnar grains were highly oriented along the (002) direction when the film processing temperature was 600 degrees C. The optical transmission and PL results also indicated that highest crystalline quality of the ZnO films could be obtained at elevated temperatures. (c) 2005 Elsevier B.V. All rights reserved.

Kinetically controlled InN nucleation on GaN templates by metalorganic chemical vapour deposition

This paper presents a study on the nucleation and initial growth kinetics of InN on GaN, especially their dependence on metalorganic chemical vapour deposition conditions. It is found that the density and size of separated InN nano-scale islands can be adjusted and well controlled by changing the V/III ratio and growth temperature. InN nuclei density increases for several orders of magnitude with decreasing growth temperature between 525 and 375 degrees C. At lower growth temperatures, InN thin films take the form of small and closely packed islands with diameters less than 100 nm, whereas at elevated temperatures the InN islands grow larger and become well separated, approaching an equilibrium hexagonal shape due to enhanced surface diffusion of adatoms. The temperature dependence of InN island density gives two activation energies of InN nucleation behaviour, which is attributed to two different kinetic processes related to In adatom surface diffusion and desorption, respectively.

The influence of growth temperature and input V/III ratio on the initial nucleation and material properties of InN on GaN by MOCVD

The effects of growth temperature and V/III ratio on the InN initial nucleation of islands on the GaN (0 0 0 1) surface were investigated. It is found that InN nuclei density increases with decreasing growth temperature between 375 and 525 degrees C. At lower growth temperatures, InN thin films take the form of small and closely packed islands with diameters of less than 100 nm, whereas at elevated temperatures the InN islands can grow larger and well separated, approaching an equilibrium hexagonal shape due to enhanced surface diffusion of adatoms. At a given growth temperature of 500 degrees C, a controllable density and size of separated InN islands can be achieved by adjusting the V/III ratio. The larger islands lead to fewer defects when they are coalesced. Comparatively, the electrical properties of the films grown under higher V/III ratio are improved.

Measurement of threading dislocation densities in GaN by wet chemical etching

We demonstrate a technique based on wet chemical etching that enables quick and accurate evaluation of edge- and screw/mixed-type threading dislocations (TDs) in GaN. Large and small etch pits are formed by phosphoric acid on the etched surfaces. The large etch pits are attributed to screw/mixed TDs and the small ones to edge TDs, according to their locations on the surface and Burgers vectors of TDs. Additionally, the origin of small etch pits is confirmed by a transmission electron microscopy. The difference in the size of etch pits is discussed in view of their origin and merging. Overetching at elevated temperatures or for a long time may result in merging of individual etch pits and underestimating of the density of TDs. Wet chemical etching has also been proved efficient in revealing the distribution of TDs in epitaxial lateral overgrowth GaN.

青杨(Populus cathayana Rehd.)雌雄植株对干旱胁迫的生理生态响应差异

随着全球气候变暖和温室效应加剧，干旱和荒漠化成为威胁人类生存和发展的主要 灾害，许多被子植物对干旱胁迫的生理、生态和生化响应已逐步得以报道，但很少有开 展干旱胁迫对雌雄异株植物的影响方面的研究。由于这类植物在长期进化过程中已经在 生长、性比、生殖格局、空间分布、资源配置和生物量分配等方面形成了明显的性别差 异，因此，干旱胁迫必将对其雌雄植株产生不同的生理生态影响。本研究以青杨为模式 植物，采用植物生态、生理及生物化学等研究方法，系统研究青杨雌雄植株在常温、增 温以及喷施外源脱落酸的条件下对干旱胁迫的响应，揭示其在生长形态、生物量分配、 光合作用、用水效率和生理生化等方面的性别间差异。主要研究结果如下： 1. 青杨雌雄植株对干旱胁迫的综合响应。 与较好水分条件相比，干旱胁迫显著降低了青杨雌雄植株的光合作用和生长发育， 影响了许多生理生化过程，并导致雌雄植株在生长发育、气体交换、用水效率、膜脂抗 氧化和抗氧化系统酶活性方面表现出显著的性别间差异。在较好水分条件下，雌雄植株 之间在株高、基径、生物量、净光合速率、蒸腾速率、用水效率以及丙二醛、脱落酸和 游离脯氨酸等生化物质含量方面均无显著差异。但在干旱胁迫下，雄株在生长发育、气 体交换、水分利用效率、膜脂过氧化保护和抗氧化系统酶活性方面均显著高于雌株，表 现出比雌株更高的株高、基径、叶面积、总叶片数、总生物量、总色素含量、类胡萝卜 素含量、净光合速率、蒸腾速率、羧化效率、光系统II最大光化学效率、内在水分利用 效率、碳同位素组分、过氧化氢酶和过氧化物酶活性等，而在CO2补偿点、比叶面积、 叶绿素a/b、丙二醛、脱落酸和超氧化物歧化酶活性等指标上显著低于雌株。与雌株相比， 雄株表现出更高的干旱胁迫适应能力，而雌株的生长发育和生理生化过程更易遭受干旱 胁迫的影响。 2. 干旱胁迫下的青杨雌雄植株对增温处理的综合响应 与环境温度相比，增温在干旱胁迫前后均显著促进了雌雄植株的生长发育、气体交 换，降低水分利用效率，影响生化物质含量，并促使青杨雌雄植株之间在干旱胁迫下表 现出显著的差异。在较好水分条件下，增温导致雌株的株高、基径、叶面积、总叶片数、 总生物量和超氧化物歧化酶活性显著高于雄株，而用水效率、丙二醛、脱落酸和游离脯 氨酸、抗坏血酸过氧化物酶和过氧化物酶活性低于雄株。在干旱胁迫下，增温将导致雄 株的株高、基径、叶面积、总生物量、净光合速率、蒸腾速率、气孔导度、总色素含量、 相对含水量、过氧化氢酶和抗坏血酸过氧化物酶活性等显著高于雌株，而光系统II 最大 光化学效率、内在水分利用效率、碳同位素组分、丙二醛、脱落酸、游离脯氨酸和超氧 化物歧化酶活性显著低于雌株。与雄株相比，水分较好条件下的增温有利于促进雌株的 生长发育，并在生理生态特征上优于雄株。而干旱胁迫下的增温则加剧了水分胁迫强度， 致使雌株的生长发育遭受比雄株更多的负面影响。 3. 干旱胁迫下的青杨雌雄植株对喷施外源脱落酸处理的综合响应 与对照相比，在干旱胁迫下喷施外源脱落酸可显著增加青杨雌雄植株的生长发育、 气体交换、降低水分利用效率，影响了生化物质含量，并导致青杨雌雄植株之间在干旱 胁迫下表现出显著的生理生态差异。在干旱胁迫下，喷施外源脱落酸致使雌株的株高、 叶面积、叶干重、细根干重、总生物量、净光合速率、蒸腾速率、气孔导度、光系统II 最大光化学效率、非光化学淬灭系数、相对含水量、总光合色素、类胡萝卜素、脱落酸、 超氧化物歧化酶和过氧化物酶活性的增加量显著高于雄株，而根重比、根冠比、细根/ 总根、比叶面积、内在水分利用效率、碳同位素组分、丙二醛、脯氨酸、过氧化氢酶和 抗坏血酸过氧化物酶活性等指标的减少量上显著低于雄株。与对照相比，干旱胁迫下的 喷施外源脱落酸则一定程度能减缓植株遭受胁迫的压力，促进植株生长和气体交换，减 少了植株体内的过剩自由基数量，并促使雌株的生长发育和光合能力显著提高，增强其 抗干旱胁迫能力。 With development of global warming and greenhouse effect, drought and desertification have been became main natural disasteres in resent years. Studies on ecophysiological responses of most angiosperm species to environmental stress have been reported, but little is known about dioecious plant responses to drought stress. Since significant differences on growth, survival, reproductive patterns, spatial distribution, as well as resource allocation between males and females of dioecious plant have been formed during evolutionary process, sexual different ecophysiological responses should be caused by drought stress. In this experiment, Populus cathayana Rehd. was used as model plant to study the sex-related responses to drought by using the ecological, physiological and biochemical methods under normal atmospheric temperature, elevated temperatures and exogenous abscisic acid (ABA) application treatment respectively, and to expose the sexual differences in growth, biomass allocation, photosynthesis, water use efficiency and some biochemical material contents in the males and females of dioecious plant. The results are follows: 1. A large set of parallel responses of males and females of P. cathayana to drought stress Compared with well-watered treatment, drought significantly decreased growth and photosynthesis of P. cathayana individuals, affected some physiological and biochemical processes, and induced males and females to exhibit obvious sexual differences in growth, gas exchange, water use efficiency, lipid peroxidation protection and antioxidant defenses enzyme system. Under well-watered treatment, there were no significant sexual differences in height growth (HG), basal diameter (BD), dry matter accumulation (DMA), net photosynthesis rate (A), transpiration (E), water use efficiency (WUE), and malondialdehyde (MDA), abscisic acid (ABA) and praline (Pro). However, under drought stress, males were found to exhibit higher HG, BD, leaf area (LA), total leaf number (TLA), DMA, total chlorophyll contents (TC), carotenoids content (Caro), A, E, carboxylation efficiency (CE), the maximum efficiency of PSII (Fv/Fm), intrinsic water use efficiency (WUE ), carbon isotope composition (δ13C), catalase (CAT), peroxidase (POD) and lower CO2 compensation point (Γ), specific leaf area (SLA), chlorophyll a/b ratio (Chla/Chlb), MDA, ABA and superoxide dismutase (SOD) than females. The results suggest that males possess greater drought resistance than do females and females suffer more negative effect on growth and development, physiological and biochemical processes than males under drought stress. 2. A large set of parallel responses of drought-stressed males and females of P. cathayana to elevated temperatures Compared with environmental temperature, elevated temperature treatment significant increased growth and gas exchange, decreased water use efficiency, changed some biochemical material contents of P. cathayana individuals, and induced males and females to exhibit obvious differences under drought stress. Under good water condition, elevated temperature treatment caused females to show significant higher HG, BD, LA, TLN, DMA, SOD activity, and great lower WUE, MDA, ABA, Pro, ascorbate peroxidase (APX) and POD than do males. On contrary, under drought condition, elevated temperature treatment induced males to exhibit higher HG, BD, LA, DMA, A, E, stomatal conductance (gs), relative water content (RWC), CAT, APX activity but lower Fv/Fm, WUE, δ13C, MDA, ABA, Pro, SOD activity than do females. The results suggest that females will benefit from elevating temperature under good water condition by possessing better ecophysiological processes than that of males, but will suffer from greater negative effects than do males when grown under drought stress with elevated temperature treatment. 3. A large set of parallel responses of drought-stressed males and females of P. cathayana to exogenous ABA application Compared with controls, exogenous ABA application under drought greatly increased growth and gas exchange, decreased water use efficiency, changed some biochemical material contents in P. cathayana individuals, and induced males and females to exhibit obvious sexual differences under drought. Under drought stress, exogenous ABA application induced females to exhibit more increases in HG, LA, leaf weight (LW), fine root weight (FRW), DMA, A, E, g, Fv/Fm, non-photochemical quenching coefficient (qN), RWC, TC, Caro, ABA, SOD, POD s activity than males, but to show lower decreases in root/weight ratio (RWR), root mass/foliage area ratio (RF), fine root/total root ratio (FT), SLA, WUE, δ13C, MDA, Pro, CAT, APX than males. The results suggest that exogenous ABA application under drought stress will eliminate negative damages caused by drought stress at a certain extent，promote the growth and gas exchange of plant and decrease the number of superfluous 1O2 in plant cells of males and females of P. cathayana. Furthermore, exogenous ABA application promoted more drought resistance in females than in males by increasing more growth and photosynthetic capacity in females under drought stress.

A study of the suppression of the high-temperature helium embrittlement in an oxide-particle dispersion strengthened alloy

In this paper, an investigation on the micro-structure of an Fe-base oxide-dispersion-strengthened (ODS) alloy irradiated with high-energy Ne-20 ions to different doses at a temperature around 0.5T(m) (T-m is the melting point of the alloy) is presented. Investigation with the transmission electron microscopy found that the accelerated growth of voids at grain-boundaries, which is usually a concern in conventional Fe-base alloys under conditions of inert-gas implantation, was not observed in the ODS alloy irradiated even to the highest dose (12000 at.ppm Ne). The reason is ascribed to the enhanced recombination of point defects and strong trapping of Ne atoms at the interfaces of the nano-scale oxide particles in grains. The study showed that ODS alloys have good resistance to the high-temperature inter-granular embrittlement due to inert-gas accumulation, exhibiting prominence of application in harsh situations of considerable helium production at elevated temperatures like in a fusion reactor.

Effect of Zn concentration on the microstructures and mechanical properties of extruded Mg-7Y-4Gd-0.4Zr alloys

Microstructures and mechanical properties of the Mg-7Y-4Gd-xZn-0.4Zr (x = 0.5, 1.5, 3, and 5 wt.%) alloys in the as-cast, as-extruded, and peak-aged conditions have been investigated by using optical microscopy, scanning electron microscope, X-ray diffraction, and transmission electron microscopy. It is found that the peak-aged Mg-7Y-4Gd-1.5Zn-0.4Zr alloys have the highest strength after aging at 220 A degrees C. The highest ultimate tensile strength and yield tensile strength are 418 and 320 MPa, respectively. The addition of 1.5 wt.% Zn to the based alloys results in a greater aging effect and better mechanical properties at both room and elevated temperatures. The improved mechanical properties are mainly ascribed to both a fine beta' phase and a long periodic stacking-ordered structure, which coexist together in the peak-aged alloys.