Benzene electro-oxidation in a PEMFC for phenol and electricity cogeneration

In the present investigation, the electrochemically-assisted oxidation of benzene in a H-2-O-2 proton exchange membrane fuel cell (PEMFC) for electricity and phenol cogeneration is studied. Experiments were carried out in a PEMFC electrochemical reactor using Pd black as cathode electrocatalyst at 60 and 80 degrees C, respectively and 1 atm back pressure. Indeed, it was found that the only product detected under the examined experimental conditions was phenol. The online GC product analysis revealed that it is impossible to produce phenol when the fuel cell circuit is open (I = 0) under all the examined experimental conditions. When the fuel cell circuit was closed, however, the phenol yield was found to follow a volcano-type dependence on the cur-rent of the external circuit. It was found that the maximum phenol yield was 0.35% at 100 mA/cm(2) at 80 degrees C. At the same time, the PEMFC performance was also investigated during the phenol generation process. Furthermore, experiments with the rotating ring disc electrode (RRDE) technique showed that the intermediate oxidation product, i.e. H2O2 existed during the oxygen electro-reduction process. The cyclic voltammograms showed that benzene was strongly adsorbed on the Pd surface, leading to a degradation of the PEMFC performance. (c) 2005 Elsevier B.V. All rights reserved.

低损耗193nm反射膜的设计

采用1/4规整膜系,从电场强度、吸收损耗及散射损耗的分布几个方面,对影响193 nm反射膜性能的因素进行了分析。以分析结果为基础,对低损耗193 nm反射膜的设计进行了探讨。结果表明:在空气侧的外膜层中电场强度较大,随着层数向内过渡,电场强度迅速减小;高折射率材料膜层的吸收损耗明显高于低折射率材料膜层的吸收损耗,而且靠近空气侧最外层的高折射率膜层的吸收损耗最大;按由外层向内层过渡的方向,吸收损耗迅速减小,减小的速度与高低折射率材料折射率的比值相关;表面散射损耗与两种材料的折射率比值成正比,但折射率比值减小后只能通过增加膜层数来获得一定的反射率,而这样又会使表面粗糙度增加,并且引入其它的损耗。因此,选择折射率差值适当大一些的材料对降低散射损耗是有利的。设计了27层膜堆的193 nm反射膜,设计反射率在98%以上。

Reliable concentrated photovoltaic system with compound concentrator

Concentrated photovoltaic systems (CPVSs) draw more and more attention because of high photovoltaic conversion efficiency, low consumption of solar cell, and low cost of power generation. However, the fallibility of the tracker in such systems has hindered their practical application for more than twenty years. The tracker is indispensable for a CPVS since only normal-incident sunlight can be focused on the solar cell chips, even a slight deviation of incident light will result in a significant loss of solar radiation, and hence a distinct decrease in electricity output. Generally, the more accurate the tracker is, the more reliable the system is. However, it is not exactly the case for a CPVS reliability, because the more accurate the tracker is, the better environment it demands. A CPVS is usually has to subjected to harsh environmental conditions, such as strong wind, heavy rain or snow, and huge changes of temperature, which leads to the invalidation of the system's high-accuracy tracker. Hence, the reliability of a CPVS cannot be improved only by enhancing the tracker's accuracy. In this paper, a novel compound concentrator, combination of Fresnel lens and photo-funnel, has been adopted in a prototype CPVS. Test results show that the compound concentrator can relax the angle tolerance from one tenth to five degrees of arc at 400 suns, which can help a CPVS endure serious environment and remain its reliability over long period. The CPVS with compound concentrator is attractive for commercial application.

双面太阳电池垂直安装发电性能的测试

双面太阳电池是一种非常规太阳电池。本文通过建立光伏组件-控制器-蓄电池-负载试验系统，对日立公司双面受光单晶硅太阳电池组件分别在东西和南北朝向情况下垂直地面安装时的功率输出特性进行了测试和分析。根据应用测试结果，总结了双面受光太阳电池的应用优缺点和可能的应用方式。

生物质气化与废弃物焚烧联合发电的技术经济分析

介绍了生物质气化与废弃物焚烧联合发电技术项目，确定了该项目经济效益的评价指标，定量计算了项目的投资回收期、净现值和内部收益率。同时还对燃料费用、上网电价和固定资产变化引起的敏感性进行分析。结果表明，该联合发电技术的动态投资回收期为9.05a，净现值为2770万元，内部收益率为15.82％，三个经济指标均符合行业标准。从经济角度看是完全可行的。

广东实施电力移峰填谷战略的计策

广东实施电力移峰填谷战略的计策GangDong Enforce the Device of Strategy for Displace Electricity Peakto Valey郭开华舒碧芬刘彦华（中科院广州能源研究所）（广东省制冷学会）（一）广东电力现状我省电力...

A study on the economic efficiency of hydrogen production from biomass residues in China

As part of Pilot Project of KIP of CAS, a feasibility study of hydrogen production system using biomass residues is conducted. This study is based on a process of oxygen-rich air gasification of biomass in a downdraft gasifier plus CO-shift. The capacity of this system is 6.4 t biomass/d. Applying this system, it is expected that an annual production of 480 billion N m(3) H-2 will be generated for domestic supply in China. The capital cost of the plant used in this study is 1328$/(N m(3)/h) H-2 out, and product supply cost is 0.15$/N m(3) H-2. The cost sensitivity analysis on this system tells that electricity and catalyst cost are the two most important factors to influence hydrogen production cost.

The cost estimate for a novel cheap solar cell

The estimate for the lowest cost of SODL (silicon on defect layer) solar cell is made according to the price standard of present market. The estimate shows that the PV (photovoltaics) energy costs can be reduced from today's 25-30 cents/(kW h) to 7-8 cents/(kW h) which is comparable with the present cost of electricity generated by traditional energy sources such as fossil and petroleum fuels. The PV energy costs could be reduced to a value lower than 7-8 cents(kW h) by developing SODL technology. The SODL solar cell manufacture featuring simple processes is suitable to large scale automated assembly lines with high yield of large area cells. Some new ideas are suggested, favoring the further reduction in the cost of commercial solar cells.

无介体双室微生物燃料电池产电性能初步研究

本文对无介体双室微生物燃料电池的产电性能进行了初步研究，并根据不同运行阶段产电性能的优劣，对其中微生物的差异性进行了比较分析。全文分为两个部分： 第一部分：以乙酸钠为阳极原料构建双室微生物燃料电池（MFC），研究不同阴极受体、外接电阻、乙酸钠浓度和pH等因素对电池产电性能的影响，研究结果表明：在500mL的阴阳极反应体系中，选用乙酸钠作为阳极底物，质量浓度为6.46 g/L， pH 7.0，接入500Ω外电阻，阴极电子受体选择高锰酸钾的情况下，微生物燃料电池产电性能最好，最大电功率密度达到294.72 mW/m2，库伦效率能达到25.87%。在确定最适外接电阻阻值的同时对MFC内阻进行测定，阻值为871.87Ω。 第二部分：微生物燃料电池运行中，比较以厌氧污泥作为接种源的第一阶段和只接入附着有大量微生物电极的第二阶段的产电性能，得出第二阶段产电性能优于第一阶段，最大电功率密度达到353.57mW/m2，比第一阶段提高58.85 mW/m2；库伦效率为39.35%，增幅达52％左右；针对微生物燃料电池运行过程中，底物CH3COONa可能存在其它的代谢途径，本实验进行了第二阶段产电性能与CH3COONa消耗率关系以及阳极液面上方气体成分和含量的研究，发现第二阶段50h前CH3COONa的大量消耗主要用于微生物的生长，在整个运行过程中，阳极液面上方含有CH4和CO2；对气体测定的同时还发现，振荡能增强电功率密度的输出；通过对电极上和污泥中微生物差异性分析得出，δ-变形菌纲、β-变形菌纲和拟杆菌门的菌种更适应微生物燃料电池的运行环境，能在电极上大量富集，提高电池的产电性能，只接入附着有大量微生物的电极能有效降低热袍菌纲的菌种数量，降低了CH3COONa的无为消耗，有效提高了电池的库伦效率。 Electricity production in the mediator-less two-chambered microbial fuel cell(MFC) was researched. Based on the result in the different operation phase in the MFC, the microbial diversity was analysed. The paper involved two parts: Part 1: A two-chambered microbial fuel cell (MFC) was constructed with high-concentration sodium acetate as fuel in the anode. The influence of different electron acceptors in the cathode, external resistance value, pH value and concentration of sodium acetate on electricity generation in MFC was investigated. The result showed that the maximum power density of 294.72 mW/m2 and the coulombic efficiency of 25.87% was achieved at sodium acetate concentration of 6.46 g/L, pH 7.0, external resistance 500Ωin the anode and when using potassium permanganate as electron acceptor in the cathode. While decided the value of resistor, we found that shaking has effect on electricity production in the MFC. Part 2: Comparing the electricity production in different operation phases when using anaerobic sludge as inoculum in the first phase and microbes in the anodic electrode as inoculum in the second phase, the result showed that electricity production in the second phase was more than that in the first phase, the maximum power density of 353.57 mW/m2 and the coulombic efficiency of 39.35% was achieved, 58.85 mW/m2 and 52％ more than that in the first phase, respectively. According to the fact that CH3COONa might be metabolized in other pathway in the running process in the MFC, we determining the relationship between electricity production and CH3COONa consumption, and the gas content in the anode, we found that CH3COONa was mainly used for microbe growth before 50h, and the anode contained CH4 and CO2. At the same time, we found that shaking could improve power density. The analysis on diversity of microbe in the anodic electrode and anaerobic sludge showed that δ-proteobacterium, β-proteobacterium and Bacteroidetes adapted themselves to the running environment of MFC. The anode could enrich them to improve the electricity production while reduced the quantity of Thermotogales, which were obligately anaerobic organotrophs with a fermentative metabolism, to increase the coulombic efficiency effectively.

Fabrication of a miniature twin-fuel-cell on silicon wafer

The fabrication and performance evaluation of a miniature twin-fuel-cell on silicon wafers are presented in this paper. The miniature twin-fuel-cell was fabricated in series using two membrane-electrode-assemblies sandwiched between two silicon substrates in which electric current, reactant, and product flow. The novel structure of the miniature twin-fuel-cell is that the electricity interconnect from the cathode of one cell to the anode of another cell is made on the same plane. The interconnect was fabricated by sputtering a layer of copper over a layer of gold on the top of the silicon wafer. Silicon dioxide was deposited on the silicon wafer adjacent to the copper layer to prevent short-circuiting between the twin cells. The feed holes and channels in the silicon wafers were prepared by anisotropic silicon etching from the back and front of the wafer with silicon dioxide acting as intrinsic etch-stop layer. Operating on dry H-2/O-2 at 25 degreesC and atmospheric pressure, the measured peak power density was 190.4 mW/cm(2) at 270 mA/cm(2) for the miniature twin-fuel-cell using a Nafion 112 membrane. Based on the polarization curves of the twin-fuel-cell and the two single cells, the interconnect resistance between the twin cells was calculated to be in the range from 0.0113 Omega (at 10 mA/cm(2)) to 0.0150 Omega (at 300 mA/cm(2)), which is relatively low. (C) 2003 Elsevier Science Ltd. All rights reserved.

Dye-Sensitized Solar Cells with a High Absorptivity Ruthenium Sensitizer Featuring a 2-(Hexylthio)thiophene Conjugated Bipyridine

We conjugated 2-(hexylthio)thiophene with bipyridine to construct a new heteroleptic polypyridyl ruthenium sensitizer exhibiting a charge-transfer band at 550 nm with a molar extinction coefficient of 18.7 x 10(3) M-1 cm(-1). In contrast to its analogues Z907 and C101, a mesoporous titania film stained with this new sensitizer featured a short light absorption length, allowing for the use of a thin photoactive layer for efficient light-harvesting and conversion of solar energy to electricity. With a preliminary testing, we have reached 11.4% overall power conversion efficiency measured at the air mass 1.5 global conditions. Transient photoelectrical decays and electrical impedance spectra were analyzed to picture the intrinsic physics of temperature-dependent photovoltage and photocurrent.

A biofuel cell harvesting energy from glucose-air and fruit juice-air

The membraneless biofuel cell (BFC) is facile prepared based on glucose oxidase and laccase as anodic and cathodic catalyst, respectively, by using 1,1'-dicarboxyferrocene as the mediators of both anode and cathode. The BFC can work by taking glucose as fuel in air-saturated solution, in which air serves as the oxidizer of the cathode. More interestingly, the fruit juice containing glucose, e.g. grape, banana or orange juice as the fuels substituting for glucose can make the BFC work. The BFC shows several advantages which have not been reported to our knowledge: (1) it is membraneless BFC which can work with same mediator on both anode and cathode; (2) fruit juice can act as fuels of BFCs substituting for usually used glucose; (3) especially, the orange juice can greatly enhance the power output rather than that of glucose, grape or banana juice. Besides, the facile and simple preparation procedure and easy accessibility of fruit juice as well as air being whenever and everywhere imply that our system has promising potential for the development and practical application of BFCs.