Measurement of respiratory acoustic impedance in children by a modified forced oscillation method

An introduction to a modified forced oscillation method, square-wave excitation technique, including fundamentals and methods, as used in respiratory function examination. On the basis of experimental results and theoretical predictions, we suggest that Respiratory Acoustic Impedance (RAI) measurement by spectral analysis can significantly improve estimation of contribution to RAI from different part of respiratory tract. The outcome is of considerable interest in the study of lung disease, such as COPD and asthma in young children.

Low-amplitude BSRs and gas hydrate concentration on the northern margin of the South China Sea

The passive northern continental margin of the South China Sea is rich in gas hydrates, as inferred from the occurrence of bottom-simulating reflectors (BSR) and from well logging data at Ocean Drilling Program (ODP) drill sites. Nonetheless, BSRs on new 2D multichannel seismic reflection data from the area around the Dongsha Islands (the Dongsha Rise) are not ubiquitous. They are confined to complex diapiric structures and active fault zones located between the Dongsha Rise and the surrounding depressions, implying that gas hydrate occurrence is likewise limited to these areas. Most of the BSRs have low amplitude and are therefore not clearly recognizable. Acoustic impedance provides information on rock properties and has been used to estimate gas hydrate concentration. Gas hydrate-bearing sediments have acoustic impedance that is higher than that of the surrounding sediments devoid of hydrates. Based on well logging data, the relationship between acoustic impedance and porosity can be obtained by a linear regression, and the degree of gas hydrate saturation can be determined using Archie's equation. By applying these methods to multichannel seismic data and well logging data from the northern South China Sea, the gas hydrate concentration is found to be 3-25% of the pore space at ODP Site 1148 depending on sub-surface depth, and is estimated to be less than values of 5% estimated along seismic profile 0101. Our results suggest that saturation of gas hydrate in the northern South China Sea is higher than that estimated from well resistivity log data in the gas hydrate stability zone, but that free gas is scarce beneath this zone. It is probably the scarcity of free gas that is responsible for the low amplitudes of the BSRs.

Estimation of gas hydrate saturation using constrained sparse spike inversion: Case study from the northern South China Sea

Bottom-simulating reflectors (BSRs) were observed beneath the seafloor in the northern continental margin of the South China Sea (SCS). Acoustic impedance profile was derived by Constrained Sparse Spike Inversion (CSSI) method to provide information on rock properties and to estimate gas hydrate or free gas saturations in the sediments where BSRs are present. In general, gas hydrate-bearing sediments have positive impedance anomalies and free gas-bearing sediments have negative impedance anomalies. Based on well log data and Archie's equation, gas hydrate saturation can be estimated. But in regions where well log data is not available, a quantitative estimate of gas hydrate or free gas saturation is inferred by fitting the theoretical acoustic impedance to sediment impedance obtained by CSSI. Our study suggests that gas hydrate saturation in the Taixinan Basin is about 10 - 20% of the pore space, with the highest value of 50%, and free gas saturation below BSR is about 2 - 3% of the pore space, that can rise to 8 - 10% at a topographic high. The free gas is non-continuous and has low content in the southeastern slope of the Dongsha Islands. Moreover, BSR in the northern continental margin of the SCS is related to the presence of free gas. BSR is strong where free gas occurs.

叠前叠后联合反演技术及其在QHD32-6油田的应用研究

What geophysical inversion studied includes the common mathematics physical property of inversion and the constitution and appraisal method of solution in geophysics domain, i.e. using observed physical phenomenon from the earth surface to infer space changing and physical property structure of medium within the earth. Seismic inversion is a branch of geophysical inversion. The basic purpose of seismic inversion is to utilizing seismic wave propagating law in the medium underground to infer stratum structure and space distribution of physical property according to data acquisition, processing and interpretation, and then offer the vital foundation for exploratory development. Poststack inversion is convenient and swift, its acoustic impedance inversion product can reflect reservoir interior changing rule to a certain degree, but poststack data lack abundant amplitude and travel time information included in prestack data because of multiple superimpose and weaken the sensitiveness which reflecting reservoir property. Compared with poststack seismic inversion, prestack seismic inversion has better fidelity and more adequate information. Prestack seismic inversion, including waveform inversion, not only suitable for thin strata physical property inversion, it can also inverse reservoir oil-bearing ability. Prestack seismic inversion and prestack elastic impedance inversion maintain avo information, sufficiently applying seismic gathering data with different incident angle, partial angle stack, gradient and intercept seismic data cube. Prestack inversion and poststack inversion technology were studied in this dissertation. A joint inversion method which synthesize prestack elastic wave waveform inversion, prestack elastic impedance inversion and poststack inversion was proposed by making fully use of prestack inversion multiple information and relatively fast and steady characteristic of poststack inversion. Using the proposed method to extract rock physics attribute cube with clear physical significance and reflecting reservoir characterization, such as P-wave and S-wave impedance, P-wave and S-wave velocity, velocity ratio, density, Poisson ratio and Lame’s constant. Regarding loose sand reservoir in lower member of Minghuazhen formation, 32-6 south districts in Qinhuangdao,as the research object, be aimed at the different between shallow layer loose sand and deep layer tight sand, first of all, acquire physical property parameters suitable for this kind of heavy oil pool according to experimental study, establishing initial pressure and shear wave relational model; Afterwards, performing prestack elastic wave forward and inversion research, summarizing rules under the guidance of theoretical research and numerical simulation, performing elastic impedance inversion, calculating rock physics attributes; Finally, predicting sand body distribution according to rock physics parameters, and predicting favorable oil area combine well-logging materials and made good results.

整合多尺度地球物理数据建立高分辨率储层模型的方法及应用

Most of the fields in China are in the middle-late development phase or are mature fields. It becomes more and more difficult to develop the remaining oil/gas. Therefore, it is import to enhance oil/gas recovery in order to maintain the production. Fine scale modeling is a key to improve the recovery. Incorporation of geological, seismic and well log data to 3D earth modeling is essential to build such models. In Ken71 field, well log, cross-well seismic and 3D seismic data are available. A key issue is to build 3D earth model with these multi-scales data for oil field development.In this dissertation, studies on sequential Gaussian-Bayesian simulation have been conducted. Its comparison with cokriging and sequential Gaussian simulation has been performed. The realizations generated by sequential Gaussian-Bayesian simulation have higher vertical resolution than those generated by other methods. Less differences between these realization and true case are observed. With field data, it is proved that incorporating well log, cross-well seismic and 3D seismic into 3D fine scale model is reliable. In addition, the advantages of sequential Gaussian-Bayesian simulation and conditions for input data are demonstrated. In Ken71 field, the impedance difference between sandstone and shale is small. It would be difficult to identify sandstone in the reservoir with traditional impedance inversion. After comparisons of different inversion techniques, stochastic hillclimbing inversion was applied. With this method, shale content inversion is performed using 3D seismic data. Then, the inverted results of shale content and well log data are incorporated into 3D models. This demonstrates a procedure to build fine scale models using multi scale seismic data, especially 3D seismic amplitude volume.The models generated through sequential Gaussian-Bayesian simulation have several advantages including: (1) higher vertical resolution compared with 3D inverted acoustic impedance (AI); (2) consistency of lateral variation as 3D inverted AI; (3) more reliability due to integration cross-well seismic data. It is observed that the precision of the model depends on the 3D inversion.

奇异性分析方法及其在储层预测中的应用研究

In research field of oil geophysical prospecting, reservoir prediction is refers to forecasting physical properties of petroleum reservoir by using data of seismic and well logging, it is a research which can guide oil field development. Singularities of seismic and logging data are caused by the heterogeneity of reservoir physical property. It's one of important methods that using singularity characteristics of seismic and logging data to study the reservoir physical property in recently. Among them, realization of reservoir quantitative prediction by analyzing singularity of the data and enhancing transition description of data is difficulty in method research. Based on wavelet transform and the fractal theory, the paper studied the singularity judgment criterion for seismic and logging data, not only analyzed quantitative relation between singularity data and reservoir physical property, but also applied it in practical reservoir prediction. The main achievements are: 1. A new method which provides singular points and their strength information estimation at only one single scale is proposed by Herrmann (1999). Based on that, the dissertation proposed modified algorithm which realized singularity polarity detection. 2. The dissertation introduced onset function to generalize the traditional geologic boundaries variations model which used singularity characteristics to represent the abruptness of the lithologic velocity transition. We show that singularity analysis reveals generic singularity information conducted from velocity or acoustic impedance to seismogram based on the convolution seismic-model theory. Theory and applications indicated that singularity information calculated from seismic data was a natural attribute for delineating stratigraphy boundaries due to its excellent ability in detecting detailed geologic features. We demonstrated that singularity analysis was a powerful tool to delineate stratigraphy boundaries and inverse acoustic impedance and velocity. 3. The geologic significances of logging data singularity information were also presented. According to our analysis, the positions of singularities indicate the sequence stratigraphic boundary, and there is subtle relationship between the singularity strength and sedimentary environment, meanwhile the singularity polarity used to recognize stratigraphic base-level cycle. Based on all those above, a new method which provided sedimentary cycle analysis based on the singularity information of logging data in multiple scales was proposed in this dissertation. This method provided a quantitative tool for judging interface of stratum sequence and achieved good results in the actual application.

地震资料叠前储层预测综合研究--以辽中凹陷东二下段浊积扇气藏为例

Reservoir prediction techniques from prestack seismic are among the most important ones for exploration of lithologic hydrocarbon reservoir. In this paper, we set the turbidite fan sandstone reservoir in Liao-Zhong depress as our researching target, and aims to solve the apllication difficulties on pre-stack inversion in the area, where the drilling data is scarce and the reservoir is lateral varied. Meanwhile, AVO analysis and pre-stack inversion for gas-bearing detection is systematically researched. The seismic reflection characters of gas-bearing sandstone in turbidite fan with different fluid content are defined, after analyzing results from AVO seismic simulation and porous fluid replacement of real log data, and under the guides of the seismic characters from classical gas-bearing sandstone reservoir and numerical simulation for complicate gas-bearing sandstone. It is confirmed that detecting gas-bearing sandstone in turbidite fan via AVO technologies is feasible. In terms of AVO analysis, two AVO characters, fluid detection factor and product of intercept and gradient, can effectively identify top and bottom boundaries and lateral range of tuibidite gas sand by comparing real drilling data. Cross-plotting of near and far angle stack data could avoid the correlation existing in P-G analysis. After comparing the acoustic impedance inversions with routine stacked data and AVO intercept, impedance derived from AVO intercept attribute could reduce the acoustic impedance estimating error which is caused by AVO. On the aspect of elastic impedance inversion, the AVO information in the pre-stack gathers is properly reserved by creating partial angle stack data. By the far angle elastic impedance alone, the gas sand, with abnormally low range of values, can be identified from the background rocks. The boundary of gas sand can also be clearly determined by cross-plotting of near and far angle elastic impedances. The accuracy of far angle elastic impedance is very sensitive to the parameter K, and by taking the statistical average of Vp/Vs on the targeted section in key wells, the accuracy of low frequency trends is gurranteed; the intensive absorsion within the area of the gas sand, which tends to push the spectral of seismic data to the lower end, will cause errors on the inversion result of elastic impedance. The solution is to confine the inversion on the interested area by improving the wavelet. On the aspect of prestack AVA simultaneous inversion, the constraint of local rock-physical trends between velocities of P-wave、S-wave and density successfully removes the instability of inversion, thus improves the precision of the resulting elastic parameters. Plenty of data on rock properties are derived via AVO analysis and prestack seismic data inversion. Based on them, the fluid anomaly is analysized and lithological interpretation are conducted. The distribution of gas sand can be consistently determined via various of ways, such as cross-plotting of P and G attributes, near and far partial angle stack data, near and far angle elastic impedances, λρ and Vp/Vs, etc. The shear modulo and density are also reliable enough to be used for lithological interpretation. We successfully applied the AVO analysis and pre-stack inversion techniques to gas detecting for turbidite fan sand reservoir in Liao-Zhong depression.

泥岩裂缝储层地震识别的理论和方法

During the exploration of fractured reservoirs, worldwide difficult problems will be encountered: how to locate the fractured zones, how to quantitatively determine the azimuth, density, and distribution of the fractures, and how to compute the permeability and porosity of the fractures. In an endeavor to solve these problems, the fractured shale reservoir in SiKou area of ShengLi oil field was chosen as a study area. A study of seismic predictive theory and methods for solving problems encountered in fractured reservoir exploration are examined herein. Building on widely used current fractured reservoir exploration techniques, new seismic theories and methods focusing on wave propagation principles in anisotropic medium are proposed. Additionally, integrated new seismic data acquisition and processing methods are proposed. Based on research and application of RVA and WA methods from earlier research, a new method of acoustic impedance varying with azimuth (IPVA) creatively is put forth. Lastly combining drilling data, well log data, and geologic data, an integrated seismic predictive method for cracked reservoir bed was formed. A summary of the six parts of research work of this paper is outlined below. In part one, conventional geologic and geophysical prediction methods etc. for cracked reservoir exploration are examined, and the weaknesses of these approaches discussed. In part two, seismic wave propagation principles in cracked reservoirs are studied. The wave equation of seismic velocity and attenuation factor in three kinds of fracture mediums is induced, and the azimuth anisotropy of velocity and attenuation in fracture mediums is determined. In part three, building on the research and application of AVA and WA methods by a former researcher, a new method of acoustic impedance creatively varying with azimuth (IPVA) is introduced. A practical software package utilizing this technique is also introduced. In part four, Base on previously discussed theory, first a large full azimuth 3d seismic data (70km~2) was designed and acquired. Next, the volume was processed with conventional processing sequence. Then AVA, WA, and IPVA processing was applied, and finally the azimuth and density of the fractures were quantitatively determined by an integrated method. Predictions were supported by well data that indicate the approach is highly reliable. in part five, geological conditions contributing to cracked reservoir bed formation are analyzed in the LuoJia area resulting in the discovery that the main fractured zones are related to fault distribution in the basin, that also control the accumulation of the oil and gas, the generation mechanisms and types of fractured shale reservoirs are studied. Lastly, by using full 3D seismic attributes, azimuth and density of cracked reservoir zones are successfully quantitative predicted. Using an integrated approach that incorporates seismic, geologic and well log data, the best two fractured oil prospects in LouJia area are proposed. These results herein represent a break through in seismic technology, integrated seismic predictive theory, and production technology for fractured reservoirs. The approach fills a void that can be applied both inside China, and internationally. Importantly, this technique opens a new exploration play in the ShengLi oil field that while difficult has substantial potential. Properly applied, this approach could play an important role toward stabilizing the oil field' production. In addition, this technique could be extended fracture exploration in other oil fields producing substantial economic reward.

Acoustic Emission Experiments of Rock Failure under Load Simulating the Hypocenter Condition

A series of acoustic emission (AE) experiments of rock failure have been conducted under cyclic load in tri-axial stress tests. To simulate the hypocenter condition the specimens are loaded by the combined action of a constant stress, intended to simulate

Analytical Interaction of the Acoustic Wave and Turbulent Flame

A modified resonance model of a weakly turbulent flame in a high-frequency acoustic wave is derived analytically. Under the mechanism of Darrieus-Landau instability, the amplitude of flame wrinkles, which is as functions of the expansion coefficient and the perturbation wave number, increases greatly independent of the 'stationary' turbulence. The high perturbation wave number makes the resonance easier to be triggered but weakened with respect to the extra acoustic wave. In a closed burning chamber with the acoustic wave induced by the flame itself, the high perturbation wave number is to restrain the resonance for a realistic flame.

Study of the Adsorption of Fibrinogen on Gold-Coated Silicon Wafer by an Impedance Method

In 0.1 mol/l KH2PO4–Na2HPO4 (pH 7.80) buffer solution, the potential of zero charge (PZC) and the open circuit potential of gold-coated silicon were determined to be about −0.6 and +0.10 V (vs SCE), respectively. The open circuit potential was higher than the PZC, which indicated that the surface of the gold-coated electrode had a positive charge. The ellipsometry experiment showed that the adsorption of fibrinogen onto the gold-coated silicon wafer surface arrived at a saturated state when the adsorption time exceeded 50 min. The percentage of surface without adsorbed protein, θ, was about 63%. This means that the proportion of surface actually occupied by fibrinogen was only about 37% after the adsorption arrived at saturation. The solution/protein capacitance value was determined in an impulse state around −0.59 V (vs SCE) and was stable (4.2×10−5 F) at other potentials.

Moment Tensor Analysis of the Acoustic Emission Source in the Rock Damage Process

To further investigate the mechanism of acoustic emission (AE) in the rock fracture experiment, moment tensor analysis was carried out. The AE sources characterized by crack sizes, orientations and fracture modes, are represented by a time-dependent momen

Electrochemical Impedance Spectroscopy Of Peo Coating On Aluminum Alloy In Nacl Solution

Various Plasma Electrolytic Oxidation (PEO) ceramic coatings were prepared on LY12 aluminum alloy by adjusting the concentration of sodium silicate solution. Optical microscope (OM), XRD and EIS were used to study their morphology, composition and anti corrosion behavior in NaCl solution. Increasing concentration of sodium silicate leads to the increase of the total coating thickness while too high and too low concentration lead to the decrease of inner dense layer. The main composition of PEO coatings prepared in 20, 40 and above 60g/L concentration solution are correspondingly alumina, alumina with mullite, and amorphous phase. The corrosion resistance is determined by the inner dense layer. Increasing the thickness of inner dense layer can improve the anti-corrosion performance. PEO coating's corrosion resistance in acidic, alkaline and neutral NaCl solution is proved and the corrosion mechanism involved is also discussed.

VISUALIZATION RESULTS OF AXISYMMETRICAL WAKE FLOW WITH/WITHOUT ACOUSTIC EXCITATION

Visualization results demonstrate the evolution of Kelvin-Helmholtz unstable waves into vortex pairing in a separated shear layer of a blunf circular. The results with acoustic excitation are quite different from that without acoustic excitation, and the phenomenon with excitation in a separated shear layer follows the rule of Devil s staircase, which always occurs in a non-linear dynamical system of two coupling vibrators.

Acoustic Calculation for Supersonic Turbulent Boundary Layer Flow

An approach which combines direct numerical simulation (DNS) with the Lighthill acoustic analogy theory is used to study the potential noise sources during the transition process of a Mach 2.25 flat plate boundary layer. The quadrupole sound sources due to the flow fluctuations and the dipole sound sources due to the fluctuating surface stress are obtained. Numerical results suggest that formation of the high shear layers leads to a dramatic amplification of amplitude of the fluctuating quadrupole sound sources. Compared with the quadrupole sound source, the energy of dipole sound source is concentrated in the relatively low frequency range.