YAP：Ce闪烁晶体的光致激发荧光衰减常数测量

用波长为266nm的激光激发不同尺寸、不同掺Ce^3＋浓度的YAP：Ce闪烁晶体，测量其光致激光荧光衰减常数，测量结果表明：YAP：Ce闪烁晶体的光致荧光衰减常数约为18．2ns，且与实验晶体厚度及Ce^3＋掺杂浓度（0．1％～0．6％原子分数）无关。

国产YAP：Ce闪烁晶体的相对探测能力测量

为适应在n、γ昆合脉冲辐射场中对低强度快脉冲y辐射测量的需要，近年国内新研制出实用型YAlO3：Ce（YAP：Ce）快响应无机闪烁晶体。我们使用脉冲线性电流大于1．5A的光电倍增管，分别配置这种晶体以及CeF3、NaI等晶体构成闪烁探测器，在放射性标准源场中，对晶体的相对探测能力进行测量。测量结果表明：国产新型YAP：Ce无机晶体对这1．25MeV射线的探测能力比同体积的CeF3平均高一个量级，是同体积NaI的40％左右；当晶体厚度小于2mm时，YAP：Ce与CeF2、NaI的输出比值分别大于16和44％，说明厚度越薄晶体的相对探测能力越强。

红外飞秒激光诱导Ce^3＋掺杂闪烁晶体的上转换发光研究

本文研究了红外飞秒激光照射下Ce^3＋ 掺杂的YAP和LSO两种闪烁晶体的上转换发光现象.实验发现在飞秒激光泵浦下,这两种晶体的荧光均来自于Ce^3＋离子的5d-4f跃迁.荧光强度与泵浦光功率之间的依赖关系揭示了Ce^3＋：YAP和Ce^3＋：LSO晶体的上转换过程皆由三光子吸收过程所主导.分析表明,Ce^3＋：YAP和Ce^3＋：LSO晶体中的三光子吸收是三光子同时吸收.

Spectroscopic properties of Ce : YAP scintillation crystal grown by temperature gradient technique

Spectroscopic properties of Ce-doped yttrium orthoaluminate (Ce:YAlO3 or Ce:YAP) crystals grown by temperature gradient technique (TGT) were investigated, and the effects of the growth conditions on the properties were analyzed.. Methods of optical absorption (OA), photoluminescence (PL), photoluminescence decay (PLD), X-ray excited luminescence (XL) and cathodeluminescence (CL) were used in these investigations. The results showed that the absorption band peak at 202, 394 and 532 nm originated from F and F+ color center induced by the weak reducing growth atmosphere, green emission band near 500 ran derived from Ce3+ -Ce3+ pairs and band at 650 similar to 850 run from some unintentional impurity in crystals.

Ce：YAP晶体中的孪晶缺陷

The twin defects in Ce:YAP were investigated by using synchrotron radiation topography and etch figures. The results show that the twins are {101} and {121} types, and the exchange of neighboring lattice parameters is considered to be the intrinsic factor for twining. Based on such analysis, the twin structure model was established. Otherwise, the growth experiment results show that the abrupt change of growth rate during shoulder formation tends to cause twining.

Effects of annealing on the color, absorption spectra, and light yield of Ce : YAlO3 single crystal grown by the temperature gradient technique

YAlO3 single crystal doped with Ce3+ at concentration 1% was grown by the temperature gradient technique. The as-grown crystal was pink. After H-2 annealing or air annealing at 1400degreesC for 20 h, the crystal was turned into colorless. We concluded there were two kinds of color centers in the as-grown crystal. One is F+ center attributed to absorption band peaking at about 530 nm, the other is O- center attributed to absorption band peaking at about 390 nm. This color centers model can be applied in explaining the experiment phenomena including the color changes, the absorption spectra changes, and the light yield changes of Ce:YAP crystals before and after annealing. (C) 2004 American Institute of Physics.

Indentation Creep Behavior in Ce-Based Bulk Metallic Glasses at Room Temperature

The room temperature creep behaviors of Ce-based bulk metallic glasses were examined by the use of nanoindentation. The creep rate and creep rate sensitivity of Ce-based BMGs were derived from indentation creep curves. The low creep rate sensitivity of Ce-based BMGs indicates that the room temperature creep is dominated by localized shear flow. The experimental creep curves can be described by a generalized Kelvin model. Furthermore, the creep retardation spectrum is calculated for the Ce-based metallic glasses. The results showed that creep retardation spectrum consists of two relatively separated peaks with the well defined characteristic relaxation times.

Strain Rate Dependence of Plastic Flow in Ce-based Bulk Metallic Glass During Nanoindentation

The strain rate dependence of plastic deformation of Ce60Al15CU10Ni15 bulk metallic glass was studied by nanoindentation. Even though the ratio of room temperature to the glass transition temperature was very high (0.72) for this alloy, the plastic deformation was dominated by shear banding under nanoindentation. The alloy exhibited a critical loading rate dependent serrated flow feature. That is, with increasing loading rate, the alloy exhibited a transition from less prominent serrated flow to pronounced serrated flow during continuous loading but from serrated to smoother flow during stepped loading.

An Improved Ce/Se Scheme And Its Application To Detonation Propagation

An improved two-dimensional space-time conservation element and solution element ( CE/ SE) method with second-order accuracy is proposed, examined and extended to simulate the detonation propagations using detailed chemical reaction models. The numerical results of planar and cellular detonation are compared with corresponding results by the Chapman-Jouguet theory and experiments, and prove that the method is a new reliable way for numerical simulations of detonation propagation.

Plastic deformation in Ce-based bulk metallic glasses during depth-sensing indentation

The deformation behavior and the effect of the loading rate on the plastic deformation features in (numbers indicate at.%) Ce60Al15Cu10Ni15, Ce65Al10Cu10Ni10Nb5, Ce68Al10Cu20Nb2, and Ce70Al10Cu20 bulk metallic glasses (BMGs) were investigated through nanoindentation. The load-displacement (P-h) curves of Ce65Al10Cu10Ni10Nb5, Ce68Al10Cu2, and Ce70Al10Cu20 BMGs exhibited a continuous plastic deformation at all studied loading rate. Whereas, the P-h curves of Ce60Al15Cu10Ni15 BMG showed a quite unique feature, i.e. homogeneous plastic deformation at low loading rates, and a distinct serrated flow at high strain rates. Moreover, a creep deformation during the load holding segment was observed for the four Ce-based BMGs at room temperature. The mechanism for the appearance of the "anomalous" plastic deformation behavior in the Ce-based BMGs was discussed. (c) 2006 Elsevier B.V. All rights reserved.

Simple phenomenological determination of contact stiffness and elastic modulus of Ce-based bulk metallic glasses through nanoindentation

The viscoelastic deformation of Ce-based bulk metallic glasses (BMGs) with low glass transition temperature is investigated at room temperature. Contact stiffness and elastic modulus of Ce-based BMGs cannot be derived using the conventional Oliver-Pharr method [W. C. Oliver and G. M. Pharr, J. Mater. Res. 7, 1564 (1992)]. The present work shows that the time dependent displacement of unloading segments can be described well by a generalized Kelvin model. Thus, a modified Oliver-Pharr method is proposed to evaluate the contact stiffness and elastic modulus, which does, in fact, reproduce the values obtained via uniaxial compression tests. (c) 2007 American Institute of Physics.