Structure and mechanical properties of Mg-Zn-RE system alloys

The lightest density of Mg has stimulated renewed interest in Mg based alloys for applications in the automotive, aerospace and communications industries. However, Mg in the pure form has relatively low strength, limited ductility and is susceptible to corrosion. Great efforts have been made to improve the mechanical properties of Mg alloys. Alloying Mg with other elements is one of the most important methods. An important class of Mg alloys is the Mg-Zn-RE system (RE = rare earth elements). In recent few decades, a series of new Mg-Zn-RE system alloys have been obtained, and detailed the structure and mechanical properties of the alloys. In this paper, the structure and mechanical properties of the Mg-Zn-RE alloys have been summarized. It showed that these alloys have high strength and they are prospected to be widely used in the future.

超声与磁粉强化含单宁废水生物处理研究

单宁是一种典型的有毒难降解污染物，在制革、造纸、制药、印染等行业废水中广泛存在，对水环境造成污染并且影响废水生物处理效果。本研究针对含单宁废水生物处理效率低、较高浓度时微生物受抑制且污泥容易膨胀等问题，采用超声和磁粉来强化含单宁废水生物处理，研究超声和磁粉对微生物活性、污染物去除及污泥沉降性能的影响，并对其作用机理进行了分析和探讨。 研究结果表明，活性污泥系统中单宁酸容积负荷可以达到1.8kgCOD/(m3·d)，单宁酸和COD去除率分别达到85.2%和79.6%，但如果负荷进一步增大则微生物活性迅速降低。系统在pH 5~8、温度20~35℃、DO>1 mg/L的条件下具有较好的单宁酸降解效果和处理稳定性。单宁降解动力学参数为：μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594。 磁粉对系统处理效果和污泥沉降性能有一定的促进作用，且效果要优于外磁场。适宜的磁粉粒径和投加量分别为0.05~0.15mm和1.0g/L，COD去除率比对照系统提高6.4%，SVI降低28.6%，污泥絮体结构紧密。磁粉强化主要是通过其对污泥菌胶团的凝聚、吸附作用以及对微生物活性的强化作用实现。 在适当强度（0.4W/cm2）和辐照时间（20min）的超声作用下污泥絮体和细胞膜通透性增大，酶分泌也增多，系统的COD去除率比对照提高了8.8%，单宁酶酶活提高了11%。但超声也使污泥絮体结构松散，沉降性能下降，SVI比对照系统升高9.3%。 由于污泥流失加剧导致污泥浓度相对较低，声磁联合强化系统相对于磁粉强化系统其处理效果并没有提高。但相对于单纯活性污泥系统，声磁联合作用下系统处理效果、污泥沉降性能以及系统运行稳定性都得到明显改善。本研究为难降解废水的生物处理提供了一个新的思路。 Tannins are typical refractory and toxic pollutants that commonly exist in wastewater from dye, medicine, paper and leather industries and cause many problems associated with environmental pollution and biological treatment of wastewater. Biological treatment efficiency of tannin-containing wastewater is usually low owing to its biological toxicity and low biodegradability, microbes are usually inhibited under high tannin concentration and sludge bulking frequently occurs. In this study, ultrasound and magnetic powder were used to improve the biological treatment performance of simulated tannic acid-containing wastewater. The effects of ultrasonic irradiation and magnetic powder on microbial activity, tannic acid degradation rate and sludge sedimentation were investigated. The augmentation mechanisms were analyzed and discussed. The experimental results showed that the microbes were prominently inhibited under high tannic acid concentration, but moderate degradation efficiency can be maintained under a tannic acid load of up to 1.8kgCOD/(m3·d), with the tannic acid degradation and COD removal percentage of 85.2% and 79.6% respectively. The highest degradation rates and treatment stability were achieved at pH range of 5~8, temperature range of 20~35℃ and DO concentration of above 1mg/L. The kinetic parameters were estimated, including: μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594. The microbial activity, tannic acid degradation rate and sludge sedimentation were improved by adding Fe3O4 magnetic powder, and the augmentation performance was better than external magnetic field. The appropriate particle size and dosage of magnetic powder were found to be 0.05~0.15mm and 1.0g/L, respectively, under which the COD removal percentage was improved by 6.4% and SVI value decreased by 28.6%, and compact floc structure was observed. This was mainly caused by the flocculation and adsorption effects of magnetic powder against sludge floc and the stimulation of microbial activity under appropriate magnetic field. Under appropriate ultrasonic irradiation (ultrasonic intensity 0.4W/cm2, ultrasonic irradiation time 20min), the permeability of floc and cell membrane are improved, transfer of substrate and oxygen were reinforced; meanwhile, more enzyme were produced by microbes under the slight damage caused by ultrasound. However, the floc structure became loose under ultrasonic irradiation, leading to relatively poor sedimentation, with the SVI value 9.3% higher than the control system. Although the magnetic powder-ultrasonic irradiation combined augmentation system showed no improvement in treatment performance compared with sole magnetic augmentation system owing to its relatively low sludge concentration, it guaranteed the stable operation of system, meanwhile the tannic acid degradation and sludge sedimentation were significantly improved compared with sole activated sludge system. This study gives a new idea for biological treatment of refractory wastewater.

Numerical simulation of coil-helix transition processes of gelatin

Gelatin is widely used in food, pharmaceutical, and photographic industries due to the coil-helix transition, whereas the structural inhomogeneity considerably affects its essential properties closely connecting with the industrial applications. The spatially structural inhomogeneity of the gelatin caused by the uneven and unstable temperature field is analyzed by the finite element method during the cooling-induced coil-helix transition process. The helix conversion and the crosslinking density as functions of time and spatial grid are calculated by the incremental method. A length distribution density function is introduced to describe the continuous length distributions of two kinds of triple helices.

Biosynthesis of fluorescent allophycocyanin alpha-subunits by autocatalysis in Escherichia coli

APC (allophycocyanin) is widely used for fluorescence tagging and may be a promising antioxidant agent for use within the food and pharmaceutical industries. Chromophore attachment to apo-ApcA (apo-APC alpha-subunit without chromophore) can be auto-catalysed both in vitro and in vivo. In the present study, a plasmid containing genes of apo-ApcA and chromophore synthetases (HOI (ferredoxin-dependent haem oxygenase) and PcyA (phycocyanobilin:ferredoxin oxidoreductase)] was constructed and expressed in Escherichia coli. The results show that holo-ApcA (APC alpha-subunit with chromophore) can be synthesized by autocatalysis in E. coli. Recombinant holo-ApcA showed the same spectral and fluorescent properties as PC (phycocyanin) and could serve as a good substitute for native PC for fluorescent tagging. Moreover, recombinant ApcA can inhibit hydroxyl and peroxyl radicals more strongly than holo-ApcA and native APC. The EC50 values were 296.4 +/- 22.4 mu g/ml against hydroxyl radicals and 38.5 +/- 2.6 mu g/ml against peroxyl radicals.

In vitro determination of antioxidant activity of proteins from jellyfish Rhopilema esculentum

In this study, the antioxidant activity of proteins isolated from jellyfish, Rhopilema esculentum Kishinouye (R. esculentum), was determined by various antioxidant assays, including superoxide anion radical-scavenging, hydroxyl radical-scavenging, total antioxidant activity, reducing power and metal chelating activity. Butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), alpha-tocopherol, vitamin C and mannitol were used as standards in those various antioxidant activities. The crude protein (CP) and the protein fractions isolated by Sephadex chromatography, first peak (FP) and second peak (SP), had very low reductive power and metal chelating abilities compared to EDTA, but they showed strong scavenging effects on the superoxide anion radical, hydroxyl radical and varying total antioxidant activity. FP and SP exhibited stronger scavenging effects on the superoxide anion radical than BHA, BHT or a-tocopherol. The EC50 values of FP and SP were 6.12 and 0.88 mu g/ml, respectively, while values EC50 of BHA, BHT and alpha-tocopherol were 31, 61 and 88 mu g/ml, respectively. CP, FP and SP showed far higher hydroxyl radical-scavenging activities than did vitamin C or mannitol. The EC50 values of CP, FP and SP were 48.76, 45.42 and 1.52 mu g/ml, but EC50 values of vitamin C and mannitol were 1907 and 4536 mu g/ml, respectively. In a beta-carotene-linoleate system, SP and CP showed antioxidant activity, but lower than BHA. Of the three samples, SP had the strongest antioxidant activity. So, SP may have a use as a possible supplement in the food and pharmaceutical industries. (c) 2005 Elsevier Ltd. All rights reserved.

Radical scavenging activity of protein from tentacles of jellyfish Rhopilema esculentum

In this study, radical scavenging activity of protein from tentacles of jellyfish Rhopilema esculentum (R. esculentum) was assayed including superoxide anion radical and hydroxyl radical scavenging. The protein samples showed strong scavenging activity on superoxide anion radical and values EC50 of full protein (FP), first fraction (IFF), second fraction (SF), and 30% (NH4)(2)SO4 precipitate (Fr-1) were 2.65, 7.28, 1.10, and 22.51 mu g/mL, respectively, while values EC50 of BHA, BHT, and alpha-tocopherol were 31, 6 1, and 88 pg/mL, respectively. Also, the protein samples had strong scavenging effect on hydroxyl radical and the values EC50 of FP, FF, SF, Fr-1, and Fr-2 were 48.91, 27.72, 1.82, 16.36, and 160.93 mu g/mL, but values EC50 of Vc and mannitol were 1907 and 4536 mu g/mL, respectively. Of the five protein samples, SF had the strongest radical scavenging activity and may have a use as a possible supplement in the food and pharmaceutical industries. The radical scavenging activity was stable at high temperature so that R. esculentum may be used as a kind of natural functional food. (c) 2005 Elsevier Ltd. All rights reserved.

连续生产过程CIMS的研究

比较了连续生产过程与离散生产过程的不同特点,提出了适合连续生产过程CIMS的体系结构.并从参考模型,开发工具和集成平台等三个方面探讨了实现CIMS如何走工程化和产业化道路的问题。

两种超微细矿物粉体材料的制备及应用研究

Superfine mineral materials are mainly resulted from the pulverization of natural mineral resources, and are a type of new materials that can replace traditional materials and enjoy the most extensive application and the highest degree of consumption in the present day market. As a result, superfine mineral materials have a very broad and promising prospect in terms of market potential. Superfine pulverization technology is the only way for the in-depth processing of most of the traditional materials, and is also one of the major means for which mineral materials can realize their application. China is rich in natural resources such as heavy calcite, kaolin, wollastonite, etc., which enjoy a very wide market of application in paper making, rubber, plastics, painting, coating, medicine, environment-friendly recycle paper and fine chemical industries, for example. However, because the processing of these resources is generally at the low level, economic benefit and scale for the processing of these resources have not been realized to their full potential even up to now. Big difference in product indices and superfine processing equipment and technologies between China and advanced western countries still exists. Based on resource assessment and market potential analysis, an in-depth study was carried out in this paper about the superfine pulverization technology and superfine pulverized mineral materials from the point of mineralogical features, determination of processing technologies, analytical methods and applications, by utilizing a variety of modern analytical methods in mineralogy, superfine pulverization technology, macromolecular chemistry, material science and physical chemistry together with computer technology and so on. The focus was placed on the innovative study about the in-depth processing technology and the processing apparatus for kaolin and heavy calcite as well as the application of superfine products. The main contents and the major achievements of this study are listed as follows: 1. Superfine pulverization processing of mineral materials shall be integrated with the study of their crystal structures and chemical composition. And special attention shall be put on the post-processing technologies, rather than on the indices for particle size, of these materials, based on their fields of application. Both technical feasibility and economic feasibility shall be taken into account for the study about superfine pulverization technologies, since these two kinds of feasibilities serve as the premise for the industrialized application of superfine pulverized mineral materials. Based on this principle, preposed chemical treatment method, technology of synchronized superfine pulverization and gradation, processing technology and apparatus of integrated modification and depolymerization were utilized in this study, and narrow distribution in terms of particle size, good dispersibility, good application effects, low consumption as well as high effectiveness of superfine products were achieved in this study. Heavy calcite and kaolin are two kinds of superfine mineral materials that enjoy the highest consumption in the industry. Heavy calcite is mainly applied in paper making, coating and plastics industries, the hard kaolin in northern China is mainly used in macromolecular materials and chemical industries, while the soft kaolin in southern China is mainly used for paper making. On the other hand, superfine pulverized heavy calcite and kaolin can both be used as the functional additives to cement, a kind of material that enjoys the biggest consumption in the world. A variety of analytical methods and instruments such as transmission and scanning electron microscopy, X-ray diffraction analysis, infrared analysis, laser particle size analysis and so on were applied for the elucidation of the properties and the mechanisms for the functions of superfine mineral materials as used in plastics and high-performance cement. Detection of superfine mineral materials is closely related to the post-processing and application of these materials. Traditional detection and analytical methods for superfine mineral materials include optical microscopy, infrared spectral analysis and a series of microbeam techniques such as transmission and scanning electron microscopy, X-ray diffraction analysis, and so on. In addition to these traditional methods, super-weak luminescent photon detection technology of high precision, high sensitivity and high signal to noise ratio was also utilized by the author for the first time in the study of superfine mineral materials, in an attempt to explore a completely new method and means for the study of the characterization of superfine materials. The experimental results are really exciting! The innovation of this study is represented in the following aspects: 1. In this study, preposed chemical treatment method, technology of synchronized superfine pulverization and gradation, processing technology and apparatus of integrated modification and depolymerization were utilized in an innovative way, and narrow distribution in terms of particle size, good dispersibility, good application effects, low consumption as well as high effectiveness of superfine products were achieved in the industrialized production process*. Moreover, a new modification technology and related directions for producing the chemicals were invented, and the modification technology was even awarded a patent. 2. The detection technology of super-weak luminescent photon of high precision, high sensitivity and high signal to noise ratio was utilized for the first time in this study to explore the superfine mineral materials, and the experimental results can be compared with those acquired with scanning electron microscopy and has demonstrated its unique advantages. It can be expected that further study may possibly help to result in a completely new method and means for the characterization of superfine materials. 3. During the heating of kaolinite and its decomposition into pianlinite, the diffraction peaks disappear gradually. First comes the disappearance of the reflection of the basal plane (001), and then comes the slow disappearance of the (hkl) diffraction peaks. And this was first discovered during the experiments by the author, and it has never before reported by other scholars. 4. The first discovery of the functions that superfine mineral materials can be used as dispersants in plastics, and the first discovery of the comprehensive functions that superfine mineral materials can also be used as activators, water-reducing agents and aggregates in high-performance cement were made in this study, together with a detailed discussion. This study was jointly supported by two key grants from Guangdong Province for Scientific and Technological Research in the 10th Five-year Plan Period (1,200,000 yuan for Preparation technology, apparatus and post-processing research by using sub-micron superfine pulverization machinery method, and 300,000 yuan for Method and instruments for biological photon technology in the characterization of nanometer materials), and two grants from Guangdong Province for 100 projects for scientific and technological innovation (700,000 yuan for Pilot experimentation of superfine and modified heavy calcite used in paper-making, rubber and plastics industry, and 400,000 yuan for Study of superfine, modified wollastonite of large length-to-diameter ratio).

动漫行业创业者胜任特征研究

Venture has become an important force for the sustainable economic growth of China, However, research on entrepreneurs is far failed to meet the actual needs, Animation and Comic Industry is an important component of the state-led Cultural and Creative Industries. Entrepreneurship is the rapid growth of population, but the empirical research on the Animation and Comic Industry entrepreneurs’ Competent Characteristic Model is rarely heard. As a manager of a national incubator which major in Cultural and Creative Industry, study these entrepreneurs competent characteristics is my responsibility. As an exploration, the study uses Competent Characteristic Model of classical design methods and behavior events interview method, and selects entrepreneurs which of animation and comic industry business start-up period as the objects. Through coding analysis of 31 entrepreneurs’ interview information, completed the amendment to the dictionary coding, and ultimately construct the animation and comic industry entrepreneurs need to have the threshold competence model and differentiating competence model. Differentiating competence model includes six competencies: tolerance and optimism, cooperation, creative innovation, pool talents, vision, decision-making and tempo control. Threshold competence model includes twenty features, divided into three dimensions: personal characteristics, knowledge quality, capacity of the quality. Knowledge and capacity of the quality are closely related to the core work of entrepreneurs, Personal characteristics concern the deep-seated motivation of the entrepreneurs. The study also analyses and discusses the characteristics of the entrepreneurs on the demographic variables.