Creep behavior of woven roving grp beam in three-point bending

The creep and relaxation behaviour of laminated glass fibre reinforced plastics (GRP) in three-point bending were studied both experimentally and analytically. Creep and relaxation experiments were carried out on eight types of specimens, consisting of glass fibre fabric reinforced epoxy beams. While the bending deflexion and creep strains were measured in the creep tests, the load and relaxation strain were recorded in the relaxation tests. Marked creep effects were seen in the tests, where the environment temperature was 50°C and the period of the measurement was 60 min. An attempt to predict the creep deflexion and relaxation behaviour was made. The transverse shear effect on creep deflexion was taken into account. The predicted results were compared with experimental ones. They were found to be in reasonable agreement, but the linearization assumption, upon which the relaxation behaviour analysis was based, appears to lead to larger inaccuracies in the results.

Transient state of chiral recognition in a binary mixture of cyclodextrins in capillary electrophoresis

The transient state (as the defined point where no enantioseparation is obtained in a dual chiral selector system) of chiral recognition of aminoglutethimide in a binary mixture of neutral cyclodextrins (CDs) was studied by capillary electrophoresis (CE). The following three dual selector systems were used: alpha-cyclodextrin (alpha-CD) and beta-cyclodextrin (beta-CD); alpha-CD and heptakis(di-O-methyl-beta-cyclodextrin) (DM-beta-CD); alpha-CD and heptakis(tri-O-methyl-beta-cyclodextrin) (TM-beta-CD). The S-(-) enantiomer of the analyte was more strongly retained in the presence of either alpha-CD or TM-beta-CD at pH 2.5, 100 mM phosphate buffer, while the R-(+) enantiomer was more strongly retained in the presence of either P-CD or DM-P-CD. In the more simple case, the elution order is invariably kept if the enantiomers have the same elution order in either one of the two hosts of the binary mixture. In contrast, the elution order may be switched by varying the concentration ratio of two hosts that produce opposite elution order for this particular analyte. In such a dual selector system, the enantioselectivity will disappear at the transient state at a certain ratio of host,:host, Moreover, the migration times of the two enantiomers with host, alone (diluted in buffer) is approximately equal to the migration times at the corresponding concentration of host, alone (diluted in buffer), where the ratio of concentrations of host,:host, is the same as in the binary mixture at the transient state. As found by nuclear magnetic resonance experiments, the analyte is forming a 1:1 complex with either one of the CDs applied. From this finding, a theoretical model based on the mobility difference of the two enantiomers was derived that was used to simulate the transient state. (C) 2000 Elsevier Science B.V. All rights reserved.

Application of laser cladding technology to improve the interface of thermal barrier coatings

The present study is focused on improvement of the adhesion properties of the interface between plasma-sprayed coatings and substrates by laser cladding technology (LCT), Within the laser-clad layer there is a gradient distribution in chemical composition and mechanical properties that has been confirmed by SEM observation and microhardness measurement. The residual stress due to mismatches in thermal and mechanical properties between coatings and substrates can be markedly reduced and smoothed out. To examine the changes of microstructure and crack propagation in the coating and interface during loading, the three-point bending test has been carried out in SEM with a loading device. Analysis of the distribution of shear stress near the interface under loading has been made using the FEM code ANSYS, The experimental results show clearly that the interface adhesion can be improved with LCT pretreatment, and the capability of the interface to withstand the shear stress as well as to resist microcracking has been enhanced.

Forced Dissociation of Selectin-ligand Complexes Using Steered Molecular Dynamics Simulation

Selectin-ligand interactions are crucial to such biological processes as inflammatory cascade or tumor metastasis. How transient formation and dissociation of selectin-ligand bonds in blood flow are coupled to molecular conformation at atomic level, however, has not been well understood. In this study, steered molecular dynamics (SMD) simulations were used to elucidate the intramolecular and intermolecular conformational evolutions involved in forced dissociation of three selectin-ligand systems: the construct consisting of P-selectin lectin (Lec) and epidermal growth factor (EGF)-like domains (P-LE) interacting with synthesized sulfoglycopeptide or SGP-3, P-LE with sialyl Lewis X (sLeX), and E-LE with sLeX. SMD simulations were based on newly built-up force field parameters including carbohydrate units and sulfated tyrosine(s) using an analogy approach. The simulations demonstrated that the complex dissociation was coupled to the molecular extension. While the intramolecular unraveling in P-LESGP-3 system mainly resulted from the destroy of the two anti-parallel sheets of EGF domain and the breakage of hydrogen-bond cluster at the Lec-EGF interface, the intermolecular dissociation was mainly determined by separation of fucose (FUC) from Ca2+ ion in all three systems. Conformational changes during forced dissociations depended on pulling velocities and forces, as well as on how the force was applied. This work provides an insight into better understanding of conformational changes and adhesive functionality of selectin-ligand interactions under external forces.

Plastic stress-strain fields and blunting effects during large deformations

Plastic stress-strain fields of two types of steel specimens loaded to large deformations are studied. Computational results demonstrate that, owing to the fact that the hardening exponent of the material varies as strain enlarges and the blunting of the crack tip, the well known HRR stress field in the plane strain model can only hold for the stage of a small plastic strain. Plastic dilatancy is shown to have substantial effects on strain distributions and blunting. To justify the constitutive equations used for analysis and to check the precision of computations, the load-deflection of a three-point bend beam and the load-elongation of an axisymmetric bar notched by a V-shaped cut were tested and recorded. The computed curves are in good accordance with experimental data.

Effect of grain size on slow fatigue crack propagation and plastic deformation near crack tip

Fatigue crack growth and its threshold are investigated at a stress ratio of 0.5 for the three-point bend specimen made of Austenitic stainless steel. The effect of grain size on the crack tip plastic deformation is investigated. The results show that the threshold value Δkth increases linearly with the square root of grain size d and the growth rate is slower for materials with larger grain size. The plastic zone size and ratio for different grain sizes are different at the threshold. The maximum stress intensity factor is kmax and σys is the yield strength. At the same time, the characteristics of the plastic deformation development is discontinuous and anti-symmetric as the growth rate is increased from 2·10—8 to 10−7 mm/cycle.

The concentration-jump coefficient in a rarefied binary gas-mixture

The results presented are obtained from sound velocity measurements, uniaxial compression tests, Brazilian tests and three-point bending tests. The density of microcracks in the heated rock is studied by means of optical microscopy, SEM and differential strain analysis (DSA).

氢对锆基块体非晶合金形变和开裂的影响

通过充氢和未充氢缺口拉伸试样和三点弯曲试样在SEM下的原位加载,研究了氢对Zr65Al7.5Ni10Cu17．5块体非晶合金形变和开裂过程的影响．结果表明,无论是否有氢,块体非晶的剪切带发展到临界尺寸,剪切裂纹就沿剪切带形核、扩展,它一旦张开就导致快速的断裂．断口边缘观察到的无特征区是剪切带,而不是剪切裂纹断口;剪切断口形貌和拉伸断口形貌没有本质区别．只有当长时间充氢才能形成氢鼓泡,如鼓泡很小或尚未形成,则氢对剪切带以及裂纹的形核、扩展没有明显影响;如存在较大的氢鼓泡,则当剪切带尚未充分发展时微裂纹就形核,导致低应力脆断．

微薄梁三点弯曲的尺度效应研究

应用高灵敏度的力传感器以及时间序列电子散斑干涉法,同时测出了不同厚度纯镍薄片三点弯曲试件的抗力与变形,得到薄梁中心点处的载荷与挠度曲线.应用Fleck和Hutchinson的偶应力理论,结合平面应变弯曲模型,建立了薄梁处于弹性状态和弹塑性状态的控制方程,应用Runge-Kutta法进行数值求解,并将计算得到的载荷-挠度曲线以及无量纲化弯矩-表面应变曲线和实验结果进行了比较.在理论计算过程中,没有拟合任何材料参数,所有的材料参数均来自实验测量的结果,材料特征尺度也是根据Stolken和Evans的工作给出的.结果表明:应用偶应力理论预测的结果和实验结果符合良好,而经典理论的预测结果与实验不相符合.

Numerical-Value Perturbation Method with Application of Solving Convective-Diffusion Integral Equation

The convective--diffusion equation is of primary importance in such fields as fluid dynamics and heat transfer hi the numerical methods solving the convective-diffusion equation, the finite volume method can use conveniently diversified grids (structured and unstructured grids) and is suitable for very complex geometry The disadvantage of FV methods compared to the finite difference method is that FV-methods of order higher than second are more difficult to develop in three-dimensional cases. The second-order central scheme (2cs) offers a good compromise among accuracy, simplicity and efficiency, however, it will produce oscillatory solutions when the grid Reynolds numbers are large and then very fine grids are required to obtain accurate solution. The simplest first-order upwind (IUW) scheme satisfies the convective boundedness criteria, however. Its numerical diffusion is large. The power-law scheme, QMCK and second-order upwind (2UW) schemes are also often used in some commercial codes. Their numerical accurate are roughly consistent with that of ZCS. Therefore, it is meaningful to offer higher-accurate three point FV scheme. In this paper, the numerical-value perturbational method suggested by Zhi Gao is used to develop an upwind and mixed FV scheme using any higher-order interpolation and second-order integration approximations, which is called perturbational finite volume (PFV) scheme. The PFV scheme uses the least nodes similar to the standard three-point schemes, namely, the number of the nodes needed equals to unity plus the face-number of the control volume. For instanc6, in the two-dimensional (2-D) case, only four nodes for the triangle grids and five nodes for the Cartesian grids are utilized, respectively. The PFV scheme is applied on a number of 1-D problems, 2~Dand 3-D flow model equations. Comparing with other standard three-point schemes, The PFV scheme has much smaller numerical diffusion than the first-order upwind (IUW) scheme, its numerical accuracy are also higher than the second-order central scheme (2CS), the power-law scheme (PLS), the QUICK scheme and the second-order upwind(ZUW) scheme.

Study on fatigue crack nucleation of electrodeposited nanocrystalline nickel

The mechanism of fatigue crack nucleation for nanocrystalline (nc) nickel was experimentally investigated in this paper. The samples of electrodeposited ne nickel were loaded cyclically by using a three point bending instrument at first. Then, atomic force microscopy (AFM) was used to scanning the sample surface after fatigue testing. The results indicated that, after fatigue testing, there are vortex-like cells with an average size of 108nm appeared along the crack on nc nickel sample. And, the roughness of sample surface increased with the maximum stress at the surface.

复振幅光瞳滤波器的三维超分辨性能研究

超分辨技术中现有的纯振幅型或纯相位型光瞳滤波器，大部分只能实现轴向或横向超分辨而不能实现三维超分辨，三维超分辨在三维成像系统中有着重要的作用。因此为提高成像系统中的三维分辨能力，设计了一种复振幅光瞳滤波器，并对其三维超分辨性能进行了研究。详细分析了该光瞳滤波器的第一区半径和透射率对施特雷尔比、轴向和横向超分辨因子以及旁瓣能量的影响。通过一系列的模拟证明，借助于复振幅光瞳滤波器可以实现三维超分辨。该滤波器的优点是容易实现三维超分辨，且有比较高的施特雷尔比，缺点是三维超分辨的实现总是伴随着旁瓣能量的增加，但可

Gene mapping of a new coat mutation in mouse

Gene mapping of a mouse coat mutation has been investigated. First, 100 10-bp random primers were used to amplify DNA, but the mutation could not be located by this method because there were no correlation between the amplified products and coat phenotypes. Second, by using Idh1, Car2, Mup1, Pgb1, Hbb, Es10, Es1, Mod1, Gdc1, Ce2, Es3 as genetic markers, linkage test crosses (two-point test) consisting of intercrossing uncovered BALB/c mice (homozygotes) to CBA/N and C57BL/6 mice with normal hair and backcrossing the heterozygotes of the F1 to the uncovered BALB/c mice were made. It was soon evident that the mutation was linked to Es3 on chromosome 11. Furthermore, three-point test was made by using Es3 and D11Mit8 (a microsatellite DNA) as genetic markers. The result showed that the mutation was linked to Es3 with the percentage recombination of (7.89 +/- 2.19)%, and linked to D11Mit8 with the percentage recombination of (26.38 +/- 3.57)%. The percentage recombination between Es3 and D11Mit8 was (32.90 +/- 3.81)%. The mutation was named Uncovered, with the symbol Uncv. According to the recombinations, the loci order was D11Mit8-26.30 +/- 3.57- Uncv-7.89 +/- 2.19-Es3. From the location on the chromosome, it was concluded that the mutation was a new mutation which affected the skin and hair structure of mouse. The Uncv has entered MGD (Mouse Genome Database).

Shear transformation zone volume determining ductile–brittle transition of bulk metallic glasses

Three-point bending experiments were performed on as-cast and annealed samples of Zr52.5Cu17.9Ni14.6Al10Ti5 (Vit105) bulk metallic glasses over a wide range of temperatures varying from room temperature (293 K) to liquid nitrogen temperature (77 K). The results demonstrated that the free volume decrease due to annealing and/or cryogenic temperature can reduce the propensity for the formation of multiple shear bands and hence deteriorate plastic deformation ability. We clearly observed a sharp ductile-to-brittle transition (DBT), across which microscopic fracture feature transfers from micro-scale vein patterns to nano-scale periodic corrugations. Macroscopically, the corresponding fracture mode changes from ductile shear fracture to brittle tensile fracture. The shear transformation zone volume, taking into account free volume, temperature and strain rate, is proposed to quantitatively characterize the DBT behavior in fracture of metallic glasses.

热喷涂涂层界面断裂韧性的反向三点弯曲法试验

以热喷涂NiCrBSi涂层/钢基体为材料模型,利用将涂层置于受压侧的反向三点弯曲法试验,对热喷涂涂层界面断裂现象进行分析并建立相应的界面断裂韧性计算模型.结果表明,界面裂纹起始于三点弯曲试样中部,对应于加载压头与涂层接触区域正下方的界面上,并向两侧扩展,伴随涂层屈曲,形成分层屈曲的破坏形貌.根据分层屈曲形貌建立计算模型,通过分层屈曲几何参数与屈曲临界应力、涂层内真实应力以及界面断裂韧性的关系,获得界面断裂韧性值.