A method to determine fracture toughness using cube-corner indentation

For the cube-corner indenter, an approximate linear relationship between the ratio of hardness (H) to reduced modulus (E-r) and the ratio of unloading work (W-u) to total loading work (W-t) is confirmed by finite-element calculations and by experiments. Based on this relationship a convenient method to determine the fracture toughness (K-IC) of brittle materials, especially for those at small scale, using cube-corner indentations is proposed. Finally, the method is calibrated by indentation experiments on a set of brittle materials. (C) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Simultaneous three-photon-excited violet upconversion luminescence of Ce3+: Lu2Si2O7 single crystals by femtosecond laser irradiation

We found that Ce3+:Lu2Si2O7 single crystals could be excited at 800 nm by using a femtosecond Ti:sapphire laser. The emission spectra of Ce3+:Lu2Si2O7 crystals were the same for one-photon excitation at 267 nm as for excitation at 800 nm. The emission intensity of Ce3+: Lu2Si2O7 crystals was found to depend on the cube of the laser power at 800 nm, consistent with simultaneous absorption of three 800 nm photons. The measured value of the three-photon absorption cross section is sigma'(3) = 2.44 x 10(-77) cm(6) s(2). (c) 2006 Optical Society of America.

Pressure-induced Raman-active radial breathing mode transition in single-wall carbon nanotubes

Using classical constant-pressure molecular dynamics simulations and the force constants model, radial breathing mode (RBM) transition of single-wall carbon nanotubes under hydrostatic pressure is reported. With the pressure increased, the RBM shifts linearly toward higher frequency, and the RBM transition occurs at the same critical pressure as the structural transition. The group theory indicates that the RBMs are all Raman-active; however, due to the effect of the frequency transition and the electronic structure change for tube radial deformation, the Raman intensity of the modes becomes so weak as not to be experimentally detected, which is in agreement with a recent experiment by S. Lebedkin [Phys. Rev. B 73, 094109 (2006)]. Furthermore, the calculated RBM transition pressure is well fitted to the cube of diameter (similar to 1/d(3)).

Modelling and simulation of the second-order Doppler error of a laser dual-frequency interferometer

Only the first- order Doppler frequency shift is considered in current laser dual- frequency interferometers; however; the second- order Doppler frequency shift should be considered when the measurement corner cube ( MCC) moves at high velocity or variable velocity because it can cause considerable error. The influence of the second- order Doppler frequency shift on interferometer error is studied in this paper, and a model of the second- order Doppler error is put forward. Moreover, the model has been simulated with both high velocity and variable velocity motion. The simulated results show that the second- order Doppler error is proportional to the velocity of the MCC when it moves with uniform motion and the measured displacement is certain. When the MCC moves with variable motion, the second- order Doppler error concerns not only velocity but also acceleration. When muzzle velocity is zero the second- order Doppler error caused by an acceleration of 0.6g can be up to 2.5 nm in 0.4 s, which is not negligible in nanometric measurement. Moreover, when the muzzle velocity is nonzero, the accelerated motion may result in a greater error and decelerated motion may result in a smaller error.

Nonpolarizing beam splitter designed by frustrated total internal reflection inside a glass cube

A method for the design of an all-dielectric nonpolarizing prism beam splitter utilizing the principle of frustrated total internal reflection is reported. The nonpolarizing condition for a prism beam splitter is discussed, and some single layer design examples are elaborated. The concept can be applied to a wide range of wavelengths and arbitrary transmittance values, and with the help of a computer design program examples of 400-700 nm, T-p = T-p = 0.5 +/- 0.01, with incident angles of 45 degrees and 62 degrees are given. In addition, the sensitivity and application of the design are also discussed. (c) 2006 Optical Society of America.

Novel moving-corner-cube-pair interferometer

A novel type of moving-corner-cube-pair interferometer is presented, and its principle and properties are studied. It consists of two moving corner cubes fixed together back to back as a single moving part (the moving-corner-cube-pair), four fixed plane mirrors and one beamsplitter. The optical path difference (OPD) is created by the straight reciprocating motion of the moving-corner-cube-pair, and the OPD value is eight times the physical shift value of the moving-corner-cube-pair. This novel type of interferometer has no tilt and shearing problems. It is almost ideal for the very-high-resolution infrared spectrometers.