Study on the Mechanical Properties of the Tetrahydrofuran Hydrate Deposit

Pure tetrahydrofuran hydrate and tetrahydrofuran hydrate deposits with different materials as the skeleton are synthesized in our laboratory. A series of experiments are carried out to study the mechanical properties. The stress-strain curve, strength of pure tetrahydrofuran hydrate and hydrate deposit are obtained. Some phenomenon is explained.

Influence of 5A-Type Zeolite Powder on Tetrahydrofuran Hydrate Formation and Dissociation Process

Visual observations of tetrahydrofuran (THF) hydrate formation and dissociation processes with 5A-type zeolite powder were made at normal atmospheric conditions and below zero temperature by microscope. Results indicate that 5A-type zeolite powder can promote THF hydrate growth. At the same time, in the presence of 5A-type zeolite, agglomerated crystals and vein-like crystals of THF hydrate were also formed. SA-type zeolite powder increases the crystallization temperature and decreases the dissociation temperature. The particle size distribution of 5A-type zeolite powder influences THF hydrate formation and its dissociation characteristics significantly.

Influence of 3A molecular sieve to tetrahydrofuran(THF) hydrate formation

Visual observation of the THF hydrate formation process in the presence of a 3A molecular sieve has been made at normal atmosphere and below a temperature of zero by microscopy. The results indicate that a 3A molecular sieve can induce the nucleation of the THF hydrate and promote the THF hydrate growth. With the existence of a 3A molecular sieve, the growth rate of THF hydrate is between 0.01 and 0.05 mu m/s. In comparison with the system without any 3A molecular sieve, the growth rate increases about 4 nm/s. After the THF hydrate grows into megacryst, the crystals will recombine and partially change under the same condition.

Crystallization and intriguing morphologies of compatible mixtures of tetrahydrofuran-methyl methacrylate diblock copolymer with poly(tetrahydrofuran)

The crystallization and unusual crystalline morphologies of compatible mixtures of tetrahydrofuran-methyl methacrylate diblock copolymer with tetrahydrofuran homopolymer were studied. It is shown that the PTHF [poly(tetrahydrofuran)] block of the copolymer cocrystalizes with the PTHF homopolymer in the PTHF microphase of the blend. However, the degree of crystallinity of the PTHF block is always lower than that of the PTHF homopolymer in the PTHF microphase. The crystallizability of the PTHF microphase increases appreciably with increasing PTHF microphase size and PTHF homopolymer weight fraction in the microphase. The morphology study of the blends shows that the crystalline morphology is strongly dependent on blend composition, copolymer composition and PTHF block length, as well as crystallization temperature. When alternating PTHF and PMMA [poly(methyl methacrylate)] lamellae are formed, the macroscopic crystalline morphology could be only observed when the thickness of the PTHF lamellae is large enough (similar to 20 nm). In the blend where PMMA spherical or cylindrical microphases are formed, the crystalline morphology changes dramatically with the change in the PTHF microdomain size and PMMA interdomain distance. Many unusual crystalline morphologies have been observed. A study of the solution-crystallized morphology of the blends at different temperatures shows that the morphology is also strongly dependent on the isothermal crystallization temperature, suggesting that the PMMA microdomains may have different effects on the morphology formation when the blend is crystallized at different rates.

Study of semicrystalline-amorphous diblock copolymers .1. Microphase separation, glass transition and crystallization of tetrahydrofuran methyl methacrylate diblock copolymers

The microphase separation, glass transition and crystallization of two series of tetrahydrofuran-methyl methacrylate diblock copolymers (PTHF-b-PMMA), one with a given PTHF block of M(n) = 5100 and the other with a given PTHF block of (M) over bar(n) = 7000, were studied in this present work. In the case of solution-cast materials, the microphase separation of the copolymer takes place first, with crystallization then gradually starting in the formed PTHF microphase. The T-g of the PMMA microphase shows a strong dependence on the molecular weight of the PMMA block, while the T-g of the PTHF microphase shows a strong dependence on the copolymer composition. The non-isothermal crystallization temperature (T-c) of the diblock copolymer decreases rapidly and continuously with the increase in the amorphous PMMA weight fraction; the lowest T-c of the copolymer is ca. 35 K lower than the T-c of the PTHF homopolymer. There also exists a T-c dependence on the molecular weight of the PTHF block. In addition, when the major component of the copolymer is PMMA, a strong dependence of the crystallizability of the copolymer on the molecular weight of the PTHF block is observed; the higher the molecular weight, then the stronger its crystallizability. The melting temperature of the block copolymer is dependent on the copolymer composition and the molecular weight of its crystallizable block. Copyright (C) 1996 Elsevier Science Ltd.

COMPATIBILITY AND CRYSTALLIZATION OF TETRAHYDROFURAN-METHYL METHACRYLATE DIBLOCK COPOLYMER/POLYTETRAHYDROFURAN BLENDS

The compatibility and crystallization of tetrahydrofuran-methyl methacrylate diblock copolymer (PTHF-b-PMMA)/tetrahydrofuran homopolymer (PTHF) blends were studied. Our results showed that the crystallization and morphology of compatible PTHF-b-PMMA/PTHF

TRIS(TERT-BUTYLCYCLOPENTADIENYL)NEODYMIUM-MU-CHLORO-TRIS(TETRAHYDROFURAN)LITHIUM, [ND(ETA(5)-(T)BUCP)3(MU-CL)LI(THF)3]

The title complex, tris[2(eta5)-tert-butylcyclopentadi-enyl]-mu-chloro-1:2kappa2Cl-tris(tetrahydrofuran-1kappaO)lithiumneodymium, [Nd(C9H13)3(mu-Cl)Li(C4H8O)3], consists of the neutral moiety ((t)BuCp)3Nd linked to the cation [Li(thf)3]+ by a mu-Cl bridge

Crystallization Behavior of Poly(tetrahydrofuran-b-methyl methacrylate) Diblock Copolymer

Crystallization behavior of a series of newly synthesized poly (tetrahydrofuran-b-methyl methacrylate) diblock copolymer has been studied by differential scanning calorimetry (DSC) and X-ray scattering and diffraction techniques. The results show that the

RING-OPENING POLYMERIZATION OF TETRAHYDROFURAN WITH RARE EARTH-CONTAINED CATALYSTS

Rare earth trifluoroacetates, Ln(CF3CO2)(3) (Ln = thirteen rare earth elements), combined with R(n)AlH(3-n) (R = methyl, octyl, n = 3; R = ethyl, i-Butyl, n = 2, 3) were used as catalysts for the polymerization of tetrahydrofuran (THF). The activity increased by adding propylene oxide (PO), as a promoter, to the polymerization system, producing high molecular weight polytetrahydrofuran (PTHF). The effects of Ln, PO/Ln, and Al/Ln, and others on the polymerization of THF were also studied. (C) 1993 John Wiley & Sons, Inc.

THE COMPATIBILITY AND CRYSTALLIZATION OF THE MIXTURES OF POLY (TETRAHYDROFURAN-b-METHYL METHACRYLATE) DIBLOCK COPOLYMER WITH POLYVINYL CHLORIDE HOMOPOLYMER

The compatibility and crystallization behaviour of the mixtures of poly (tetrahydrofuran-methyl methacrylate) diblock copolymer (PTHF-b-PMMA) with polyvinyl chloride has been studied. We found that the compatibility of these blends, in which there is special interaction between the homopolymer and the PMMA block of the copolymer, is much better than that of the AB/A type blends; and that the crystallization rate and crystallinity of PTHF microdomain changed greatly due to the swollen by PVC homopolymer. In this paper, these changes in cryatallization are well explained according to the theories of block copolymer blends and the density gradient model presented by JIANG Ming.