Flow Rate Measurement in Multiphase Flow Using Turbine Flow-meter

对涡轮流量传感器进行了理论分析,给出了涡轮流量计仪表常数的计算方法,讨论了获得较大固有仪表常数K_0时涡轮传感器结构参数（如叶片数、涡轮半径、口径等）的优化组合问题,通过多相流动实验,总结出K_0与流动密度之间的实验关系,由此给出用涡轮流量计测量多相流的半理论半经验公式,并在油井多相流量测量中得到了实际应用,符合较好。

Experimental Study Of Multi-Hole Cooling For Integrally-Woven, Ceramic Matrix Composite Walls For Gas Turbine Applications

In this paper, multi-hole cooling is studied for an oxide/oxide ceramic specimen with normal injection holes and for a SiC/SiC ceramic specimen with oblique injection holes. A special purpose heat transfer tunnel was designed and built, which can provide a wide range of Reynolds numbers (10(5)similar to 10(7)) and a large temperature ratio of the primary flow to the coolant (up to 2.5). Cooling effectiveness determined by the measured surface temperature for the two types of ceramic specimens is investigated. It is found that the multi-hole cooling system for both specimens has a high cooling efficiency and it is higher for the SiC/SiC specimen than for the oxide/oxide specimen. Effects on the cooling effectiveness of parameters including blowing ratio, Reynolds number and temperature ratio, are studied. In addition, profiles of the mean velocity and temperature above the cooling surface are measured to provide further understanding of the cooling process. Duplication of the key parameters for multi-hole cooling, for a representative combustor flow condition (without radiation effects), is achieved with parameter scaling and the results show the high efficiency of multi-hole cooling for the oblique hole, SiC/SiC specimen. (C) 2008 Elsevier Ltd. All rights reserved.

基于LabVIEW和声卡的数据采集系统

本文提出了一种基于LabVIEW和声卡的数据采集系统．该方法实现简单、性价比高。生成的采集软件交互性好．操作方便．并且可以根据用户的需求进行功能扩充．为低成本下构建数据采集系统提供了一种思路。

Thermal performance of a micro-combustor for micro-gas turbine system

Premixed combustion of hydrogen gas and air was performed in a stainless steel based micro-annular combustor for a micro-gas turbine system. Micro-scale combustion has proved to be stable in the micro-combustor with a gap of 2 mm. The operating range of the micro-combustor was measured, and the maximum excess air ratio is up to 4.5. The distribution of the outer wall temperature and the temperature of exhaust gas of the micro-conbustor with excess air ratio were obtained, and the wall temperature of the micro-combustor reaches its maximum value at the excess air ratio of 0.9 instead of 1 (stoichiometric ratio). The heat loss of the micro-combustor to the environment was calculated and even exceeds 70% of the total thermal power computed from the consumed hydrogen mass flow rate. Moreover, radiant hunt transfer covers a large fraction of the total heat loss. Measures used to reduce the heat loss were proposed to improve the thermal performance of the micro-combustor. The optimal operating status of the micro-combustor and micro-gas turbine is analyzed and proposed by analyzing the relationship of the temperature of the exhaust gas of the micro-combustor with thermal power and excess air ratio. The investigation of the thermal performance of the micro-combustor is helpful to design an improved microcombustor.

基于Labview开发统计过程控制软件

统计过程控制是质量管理的重要内容,介绍了SPC的原理,并用Labview软件实现了SPC软件。这种开发方法应用了Labview软件提供的统计过程控制模块,方便了程序的开发,很容易被质量人员掌握,设备改动或软件应用于别的设备时,只需简单地修改参数,大大方便了统计过程控制的普及,提高企业的质量水平。

基于LabVIEW的自组织网络的实现与应用

文章介绍了自组织神经网络在故障诊断方面的应用原理,针对自组织神经网络实现问题提出了一种通过在LabVIEW调用MATLAB应用程序实现自组织神经网络的方法。并通过轴承故障诊断的实例,证明了这种方法的有效性。

基于labview的变速箱振动测试分析系统

文章介绍了一个基于虚拟仪器技术开发的变速箱振动测试与分析系统。该系统实现了汽车变速箱振动信号的检测、分析、处理和显示存储,满足对测试过程高精度、自动化、智能化等各项测试要求。