结晶性间同立构1,2-聚丁二烯的单晶结构

近十几年来,结晶性间同立构1,2-聚丁二烯引起人们的广泛关注,但绝大多数研究工作集中在聚合物的制备、物理性质和应用方面[1～3],对于其结晶行为和晶体结构则未见报道 .原因是间同立构1,2-聚丁二烯分子侧链含有大量的双键,在较高温度下很容易交联 ,特别是高间规度的聚合物 ,由于其熔融温度高 (>200℃ )则更易产生交联,这给结晶行为和结构研究带来很大困难.结晶性间同立构1,2-聚丁二烯的晶体结构为平面锯齿链正交堆砌,Pacm空间群[4].我们曾报道了结晶性间同立构1,2-聚丁二烯的合成和溶液浇铸膜的板条状结构[5],本文采用薄膜熔体结晶的方法第一次成功地获得了间同立构1,2-聚丁二烯的单晶,并通过电子显微学和电子衍射技术确定了其晶体结构.1 实验部分1.1间同立构1,2-聚丁二烯的制备采用乙酰基丙酮铁 [Fe(acac) ]3、三异丁基铝 [Al(i-Bu)3]和氢化亚磷酸二乙酯 (DEP)的新催化体系制备间同立构1,2-聚丁二烯,具体合成路线参见文献 [5].本文所选用聚合物的1,2单元含量为 89.3 % ,间规度为 ...

Operational characteristics of a 1.2-MW biomass gasification and power generation plant

In this study, we analyzed the operational characteristics of a 1.2-MW rice husk gasification and power generation plant located in Changxing, Zhejiang province, China. The influences of gasification temperature, equivalence ratio (ER), feeding rate and rice husk water content on the gasification characteristics in a fluidized bed gasifier were investigated. The axial temperature profile in the dense phase of the gasifier showed that inadequate fluidization occurred inside the bed, and that the temperature was closely related to changes in ER and feeding rate. The bed temperature increased linearly with increasing ER when the feeding rate was kept constant, while a higher feeding rate corresponded to a lower bed temperature at fixed ER. The gas heating value decreased with increasing temperature, while the feeding rate had little effect. When the gasification temperature was 700-800C, the gas heating value ranged from 5450-6400kJ/Nm3. The water content of the rice husk had an obvious influence on the operation of the gasifier: increases in water content up to 15% resulted in increasing ER and gas yield, while water contents above 15% caused aberrant temperature fluctuations. The problems in this plant are discussed in the light of operational experience of MW-scale biomass gasification and power generation plants.

Microstructures, mechanical properties and corrosion behavior of high-pressure die-cast Mg-4Al-0.4Mn-xPr (x=1, 2, 4, 6) alloys

Mg-4Al-0.4Mn-xPr (x = 1, 2, 4 and 6 wt.%) magnesium alloys were prepared successfully by the high-pressure die-casting technique. The microstructures, mechanical properties, corrosion behavior as well as strengthening mechanism were investigated. The die-cast alloys were mainly composed of small equiaxed dendrites and the matrix. The fine rigid skin region was related to the high cooling rate and the aggregation of alloying elements, such as Pr. With the Pr content increasing, the alpha-Mg grain sizes were reduced gradually and the amounts of the Al2Pr phase and All, Pr-3 phase which mainly concentrated along the grain boundaries were increased and the relative volume ratio of above two phases was changed. Considering the performance-price ratio, the Pr content added around 4 wt.% was suitable to obtain the optimal mechanical properties which can keep well until 200 degrees C as well as good corrosion resistance. The outstanding mechanical properties were mainly attributed to the rigid casting surface layer, grain refinement, grain boundary strengthening obtained by an amount of precipitates as well as solid solution strengthening.

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

Synthesis and properties of polyimides derived from cis- and trans-1,2,3,4-cyclohexanetetracarboxylic dianhydrides

Cis-1,2,3,4-cyclohexanetetracarboxylic dianhydride (cis-1,2,3,4-CHDA) was synthesized. It was found that under such conditions as heating or boiling in acetic anhydride, cis-1,2,3,4-CHDA could be converted to its trans-isomer. The process of thermal isomerization was monitored by H-1 NMR spectra and the mechanism of conversion was proposed. Their absolute structures of cis- and trans-1,2,3,4-CHDAs were elucidated by single crystal X-ray diffraction. The polycondensations of cis- and trans-1,2,3,4-CHDAs with aromatic diamines such as 4,4'-oxydianiline (ODA), 4,4'-methylenedianiline (MDA), 4,4'-diamino-3,3'-dimethyldiphenylmethane (DMMDA), 4,4'-bis(4-aminophenoxy)benzene (TPEQ), 2,2-bis[4-(4-aminophenoxy)phenyl] propane (BAPP) were studied. It is easy to obtain higher molecular weight polyimides from trans-1,2,3,4-CHDA using conventional one-step or two-step methods. However, higher molecular weight polyimides derived from cis-1,2,3,4-CHDA could not be prepared by the usual methods (solid content ca. 10%) owing to the trend of forming cyclic oligomers.

Crystallization and phase behavior of crystalline syndiotactic 1,2-polybutadiene/isotactic polypropylene blends in solution-cast thin films

Crystallization and phase behavior in solution-cast thin films of crystalline syndiotactic 1,2-polybutadiene (s-1,2-PB) and isotactic polypropylene (i-PP) blends have been investigated by transmission electron microscopy (TEM), atomic force microscopy (AFM) and field-emission scanning electron microscopy (FESEM) techniques. Thin films of pure s-1,2-PB consist of parallel lamellae with the c-axis perpendicular to the film plane and the lateral scale in micrometer size, while those of i-PP are composed of cross-hatched and single-crystal-like lamellae. For the blends, TEM and AFM observations show that with addition of i-PP, the s-1,2-PB long lamellae become bended and i-PP itself tends to form dispersed convex regions oil a continuous s-1,2-PB phase even when i-PP is the predominant component, which indicates a strong phase separation between the two polymers during film formation. FESEM micrographs of both lower and upper surfaces of the films reveal that the s-1,2-PB lamellae pass through i-PPconvex regions from the bottom, i.e. the dispersed i-PP regions lie on the continuous s-1,2-PB phase. The structural development is attributed to an interplay of crystallization and phase separation of the blends in the film forming process.

Synthesis and structure of iron complex with 1,2-dithiolate-1,2-dicarba-closo-dodecaborane [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)]

The crystal of complex [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)] 3 belongs to monoclinic, space group P2(1) with a = 11.964(2), b = 16.527(3), c = 12.554(3) Angstrom,beta = 108.70(3)degrees, V= 2351.3(8) Angstrom(3), Z = 2, M-r = 835.95, D-c = 1.181 g/cm(3), mu (MoKalpha) = 5.30 cm(-1), f(000) = '874, R = 0.0622 and Rw 0.1538 for 1641 observed reflections with I > 2sigma(I). The ionic complex,of 3 contains the square pyramidal anion of [Fe(S2C2B10H10)(2)(THF)](-) and the tetrahedral cation of [Li(THF)(4)](+). The iron is 5-coordinated and located in the square pyramidal configuration. The iron atom and the four sulfur atoms are almost coplanar. The Lithium atom is coordinated with four oxygen atoms of four THF molecules and located in a tetrahedral configuration.

Studies on the structure of tricyclohexyltin-2-(1,2-dithioethylene)methylene-3-oxo-5-aryl-4-pentenicate

Three title compounds were prepared and the structure of title compound 2 was characterized by IR, H-1 NMR, C-13 NMR, Sn-119 NMR spectroscopy and the crystal structure of compound 2a was determined by X-ray analysis with the final R indices[I >2 sigma (I)] R-1 = 0.0350 and R-2,R-omega = 0.0888. The crystal of compound 2a belongs to triclinic system, space group P1 with a = 1.0598(6) nm, b = 1.307 4(10) nm, c = 1.378 6(10) nm, alpha = 62.666(7)degrees, beta = 72.530(2)degrees, gamma = 80. 680(2)degrees, V = 1.618 0 nm(3), D-x = 1. 444 g (.) cm(-3), Z = 1, F (000) = 728. The bond length of Sn1-O1 is 0. 2076 nm and Sn1 . . . O2 distance is 0.301 3 nm. The coordination about the tin atom can be considered as a distorted tetrahedral. The detail values of H-1 NMR, C-13 NMR, Sn-119 NMR, (2)J(119Sn-1H) and J(119Sn-13C) were obtained. delta (119Sn) = 23.836, (2)J(119Sn-1H) = 88.0 Hz, (1)J(119Sn-13C) = 347.1 Hz, (2)J(119Sn-13C) = 45.6 Hz.

(Z)-1[2-(苯基二溴化锡基)乙烯基]-1-环己醇的合成及晶体结构

报道了标题化合物〔C14H18Br2OSn〕的合成及晶体结构。该晶体属于单斜晶系，空间点群为P21/c，晶胞参数a=11.711(2)，b=9．114（2），c=16．864（3）A，β=102.94（1）°，V=1604.55（0）A3，Mr=480．78，Z=4，Dc=1．99g／cm3，u=65．20cm－1，F（000）=919，R=0．050，Rw=0．050．晶体结构由直接法解出。标题化合物分子中的锡原子被配体的2个碳、2个溴和1个氧原子配位，配位原子呈畸变的三角双锥构型，环已基为椅式构象，五员杂环为信封构象。

Synthesis and. crystal structure of N '-(4-fluorobenzylidene)-2-(1H-1,2,4-triazole-1-yl) acetohydrazide

N'-(4-fluorobenzylidene)-2-(1H-1 2,4-triazole-1-yl) acetohydrazide was synthesized by the reaction of 4-fluorobenzaldehyde with 2-(1H-1 2,4-triazole-1-yl) acetohydrazide. The structure was confirmed via elemental analysis, MS, H-1 NMR, IR, and X-ray diffraction. It crystallized in a monoclinic system with space group P2 (1) a = 0.4905 (1) nm, b = 0.8160 (2) nm, c = 1.4105 (3) nm, beta = 93.33 (3)degrees, Z = 2, V = 0.5636 (2) nm(3), D-c = 1.457 Mg/m(3), mu = 0.112 mm(-1), F(000) = 256, and final R-1 = 0.0685. Several intermolecular hydrogen-bond interactions existed in the crystal structure, facilitating the stabilization of the compound.

1-（2-萘基）-3-甲基-5-吡唑啉酮衍生试剂的制备及其在高效液相色谱-质谱法测定糖类化合物中的应用

以1-（2-萘基）-3-甲基-5-吡唑啉酮（NMP）作为柱前衍生试剂,建立了简单、灵敏的糖类组分的反相高效液相色谱测定方法。NMP与糖在氨为催化剂的条件下,于70℃下反应可获得稳定的衍生产物。在HypersilODS2反相色谱柱上,实现了8种单糖的基线分离。衍生物线性相关系数均大于0.9985,检出限为0.58-1.1pmol。利用柱后在线串联质谱的电喷雾电离正离子模式监测,获得了各组分的质谱定性及裂解规律,特别是m/z473的特征碎片离子可作为单糖NMP衍生物的判定依据。与1-苯基-3-甲基-5-吡唑啉酮（PMP）相比,NMP对糖的衍生化具有灵敏、简单、质谱裂解规律性强、重现性好等优点。该方法用于测定油菜花粉多糖中的单糖组成,结果令人满意。