Photoinduced voltage shift in a three-barrier, two-well resonant tunneling structure integrated with a 1.2-mu m-thick n-type GaAs layer

By integrating a three-barrier, two-well resonant tunneling structure with a 1.2-mu m-thick, slightly doped n-GaAs layer, a photoinduced voltage shift on the order of magnitude of 100 mV in resonant current peaks has been verified at an irradiance of low light power density. The 1.2-mu m-thick, slightly doped n-GaAs layer manifests itself of playing an important role in enhancing photoelectric sensitivity. (c) 2005 Elsevier B.V. All rights reserved.

Operational characteristics of a 1.2-MW biomass gasification and power generation plant

In this study, we analyzed the operational characteristics of a 1.2-MW rice husk gasification and power generation plant located in Changxing, Zhejiang province, China. The influences of gasification temperature, equivalence ratio (ER), feeding rate and rice husk water content on the gasification characteristics in a fluidized bed gasifier were investigated. The axial temperature profile in the dense phase of the gasifier showed that inadequate fluidization occurred inside the bed, and that the temperature was closely related to changes in ER and feeding rate. The bed temperature increased linearly with increasing ER when the feeding rate was kept constant, while a higher feeding rate corresponded to a lower bed temperature at fixed ER. The gas heating value decreased with increasing temperature, while the feeding rate had little effect. When the gasification temperature was 700-800C, the gas heating value ranged from 5450-6400kJ/Nm3. The water content of the rice husk had an obvious influence on the operation of the gasifier: increases in water content up to 15% resulted in increasing ER and gas yield, while water contents above 15% caused aberrant temperature fluctuations. The problems in this plant are discussed in the light of operational experience of MW-scale biomass gasification and power generation plants.

华南沿海近100年来2月份的极端气温事件

采用IPCC AR4规定的极端天气事件划分标准，分析1908—2008年广州、香港、

Electrosynthesis and characterization of 1,2-dibenzyl C-60: A revisit

A reinvestigation of the reaction between C-60(2-) and benzyl bromide in benzonitrile containing 0.1 M tetra-n-butylammonium perchlorate (TBAP) has shown that there are more reaction products than previously reported. Use of a silica rather than a "Buckyclutcher I" column for HPLC purification led to isolation of two previously unattained products in the reaction mixture, one of which was identified as 1,2-(PhCH2)(2)C-60 by UV-vis and NMR. The earlier incorrectly assigned 1,2-(PhCH2)(2)C-60 was identified as the methanofullerene C61HPh by X-ray single-crystal diffraction. The electrochemistry of genuine 1,2-(PhCH2)(2)C-60 shows that its first reduction potential in PhCN containing 0.1 M TBAP is cathodically shifted by 100 mV with respect to E-1/2 for reduction of 1,4-(PhCH2)(2)C-60, indicating that the addition pattern significantly affects the electrochemistry of derivatized C-60. Visible and near-IR spectra of the monoanion and dianion of 1,2-(PhCH2)(2)C-60 are also reported.

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

Synthesis and properties of polyimides derived from cis- and trans-1,2,3,4-cyclohexanetetracarboxylic dianhydrides

Cis-1,2,3,4-cyclohexanetetracarboxylic dianhydride (cis-1,2,3,4-CHDA) was synthesized. It was found that under such conditions as heating or boiling in acetic anhydride, cis-1,2,3,4-CHDA could be converted to its trans-isomer. The process of thermal isomerization was monitored by H-1 NMR spectra and the mechanism of conversion was proposed. Their absolute structures of cis- and trans-1,2,3,4-CHDAs were elucidated by single crystal X-ray diffraction. The polycondensations of cis- and trans-1,2,3,4-CHDAs with aromatic diamines such as 4,4'-oxydianiline (ODA), 4,4'-methylenedianiline (MDA), 4,4'-diamino-3,3'-dimethyldiphenylmethane (DMMDA), 4,4'-bis(4-aminophenoxy)benzene (TPEQ), 2,2-bis[4-(4-aminophenoxy)phenyl] propane (BAPP) were studied. It is easy to obtain higher molecular weight polyimides from trans-1,2,3,4-CHDA using conventional one-step or two-step methods. However, higher molecular weight polyimides derived from cis-1,2,3,4-CHDA could not be prepared by the usual methods (solid content ca. 10%) owing to the trend of forming cyclic oligomers.

Crystallization and phase behavior of crystalline syndiotactic 1,2-polybutadiene/isotactic polypropylene blends in solution-cast thin films

Crystallization and phase behavior in solution-cast thin films of crystalline syndiotactic 1,2-polybutadiene (s-1,2-PB) and isotactic polypropylene (i-PP) blends have been investigated by transmission electron microscopy (TEM), atomic force microscopy (AFM) and field-emission scanning electron microscopy (FESEM) techniques. Thin films of pure s-1,2-PB consist of parallel lamellae with the c-axis perpendicular to the film plane and the lateral scale in micrometer size, while those of i-PP are composed of cross-hatched and single-crystal-like lamellae. For the blends, TEM and AFM observations show that with addition of i-PP, the s-1,2-PB long lamellae become bended and i-PP itself tends to form dispersed convex regions oil a continuous s-1,2-PB phase even when i-PP is the predominant component, which indicates a strong phase separation between the two polymers during film formation. FESEM micrographs of both lower and upper surfaces of the films reveal that the s-1,2-PB lamellae pass through i-PPconvex regions from the bottom, i.e. the dispersed i-PP regions lie on the continuous s-1,2-PB phase. The structural development is attributed to an interplay of crystallization and phase separation of the blends in the film forming process.

Fe(2-EHA)(3)/Al(i-Bu)(3)/hydrogen phosphite catalyst for preparing syndiotactic 1,2-polybutadiene

Polymerizing 1,3-butadiene into syndiotactic 1,2-polybutadiene with art iron(III) catalyst system has been investigated. Activity of the catalyst was affected by the type of cocatalyst alkylaluminum and the phosphorus compound as an electron donor, molar ratio of catalyst components, and their aging sequence and aging time of the catalyst. The microstructure and configuration of the polymer was decided by the catalyst components, the higher [Al]/[Fe] molar ratio tending to yield syndiotactic 1,2-polybutadiene, while the higher [P]/[Fe] molar ratio favors the formation of amorphous 1,2-polybutadiene.

Synthesis and structure of iron complex with 1,2-dithiolate-1,2-dicarba-closo-dodecaborane [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)]

The crystal of complex [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)] 3 belongs to monoclinic, space group P2(1) with a = 11.964(2), b = 16.527(3), c = 12.554(3) Angstrom,beta = 108.70(3)degrees, V= 2351.3(8) Angstrom(3), Z = 2, M-r = 835.95, D-c = 1.181 g/cm(3), mu (MoKalpha) = 5.30 cm(-1), f(000) = '874, R = 0.0622 and Rw 0.1538 for 1641 observed reflections with I > 2sigma(I). The ionic complex,of 3 contains the square pyramidal anion of [Fe(S2C2B10H10)(2)(THF)](-) and the tetrahedral cation of [Li(THF)(4)](+). The iron is 5-coordinated and located in the square pyramidal configuration. The iron atom and the four sulfur atoms are almost coplanar. The Lithium atom is coordinated with four oxygen atoms of four THF molecules and located in a tetrahedral configuration.

Studies on the structure of tricyclohexyltin-2-(1,2-dithioethylene)methylene-3-oxo-5-aryl-4-pentenicate

Three title compounds were prepared and the structure of title compound 2 was characterized by IR, H-1 NMR, C-13 NMR, Sn-119 NMR spectroscopy and the crystal structure of compound 2a was determined by X-ray analysis with the final R indices[I >2 sigma (I)] R-1 = 0.0350 and R-2,R-omega = 0.0888. The crystal of compound 2a belongs to triclinic system, space group P1 with a = 1.0598(6) nm, b = 1.307 4(10) nm, c = 1.378 6(10) nm, alpha = 62.666(7)degrees, beta = 72.530(2)degrees, gamma = 80. 680(2)degrees, V = 1.618 0 nm(3), D-x = 1. 444 g (.) cm(-3), Z = 1, F (000) = 728. The bond length of Sn1-O1 is 0. 2076 nm and Sn1 . . . O2 distance is 0.301 3 nm. The coordination about the tin atom can be considered as a distorted tetrahedral. The detail values of H-1 NMR, C-13 NMR, Sn-119 NMR, (2)J(119Sn-1H) and J(119Sn-13C) were obtained. delta (119Sn) = 23.836, (2)J(119Sn-1H) = 88.0 Hz, (1)J(119Sn-13C) = 347.1 Hz, (2)J(119Sn-13C) = 45.6 Hz.

(Z)-1[2-(苯基二溴化锡基)乙烯基]-1-环己醇的合成及晶体结构

报道了标题化合物〔C14H18Br2OSn〕的合成及晶体结构。该晶体属于单斜晶系，空间点群为P21/c，晶胞参数a=11.711(2)，b=9．114（2），c=16．864（3）A，β=102.94（1）°，V=1604.55（0）A3，Mr=480．78，Z=4，Dc=1．99g／cm3，u=65．20cm－1，F（000）=919，R=0．050，Rw=0．050．晶体结构由直接法解出。标题化合物分子中的锡原子被配体的2个碳、2个溴和1个氧原子配位，配位原子呈畸变的三角双锥构型，环已基为椅式构象，五员杂环为信封构象。

塑炼1,2-聚丁二烯的无扰尺寸

利用测得(?)和[η]数据,由Stockmayer-Fixman-Burchard、Stockmayer-Kurata-Roig和Inagaki-Suzuki-Kurata方程外推,估算了塑炼过程中不同1,2-链节含量的1,2-聚丁二烯(1,2-PB)的无扰尺寸变化规律。1,2-链节含量分别为40％和87.2％时,随薄通次数的增加,无扰尺寸降低;但前者薄通50次后变化很小,后者薄通100次后仍有波动。1,2-链节含量为87.2％的1,2-PB,薄通后放置30d,其无扰尺寸随薄通次数的增加而降低的程度,均大于当日测定的结果。

钼系1,2-聚丁二烯橡胶扩大试验

以钼系化合物为主催化剂,有机铝为助催化剂,烯丙基溴为分子量调节剂,加氢汽油为溶剂,在30 L连续聚合装置上进行了 1,2-聚丁二烯橡胶合成试验。首釜聚台温度 60—80℃,2~#、3~# 釜聚合温度70—80℃。胶液用热水凝聚,湿胶经螺杆挤压机脱水干燥。所得产品性能为:[η]=2.08—2.77dL/g,ML_(1+4)100℃=57—69,分子量分散指数1.3—2.2,1,2-链节含量为 81.4—90％。聚合经 1 500 h连续运转,无挂胶和凝胶。同时对产品的充油及其与 BR、NR共混进行了试验。