Improvement of Aircraft Rolling Power by Use of Piezoelectric Actuators

Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection and the model without aileron (fictitious control surface, FCS) is studied. The analytical results show that these two cases are substantial different. In aileron deflection case, the aeroelastic effect is disadvantageous, so the structural stiffness should be high until the electrical voltage is not necessary. But in the case of FCS,the aeroelastic effect is advantageous and it means that lower structural stiffness can lead to lower voltage. Compared with aileron project, the FCS project can save structure weight.

A numerical investigation on the flow physics of koi carp (Cyprinus carpio koi) burst-and-coast swimming

Abstract—Burst-and-coast is the most common locomotion type in freely routine swimming of koi carps (Cyprinus carpio koi), which consists of a burst phase and a coast phase in each cycle and mostly leads to a straight-line trajectory. Combining with the tracking experiment, the flow physics of koi carp’s burst-andcoast swimming is investigated using a novel integrated CFD method solving the body-fluid interaction problem. The dynamical equations of a deforming body are formulated. Following that, the loose-coupled equations of the body dynamics and the fluid dynamics are numerically solved with the integrated method. The two burst modes, MT (Multiple Tail-beat) and HT (Half Tail-beat), which have been reported by the experiments, are investigated by numerical simulations in this paper. The body kinematics is predicted and the flow physics is visualized, which are in good agreement with the corresponding experiments. Furthermore, the optimization on the energy cost and several critical control mechanisms in burst-and-coast swimming of koi carps are explored, by varying the parameters in its selfpropelled swimming. In this paper, energetics is measured by the two mechanical quantities, total output power CP and Froude efficiency Fr. Results and discussion show that from the standpoint of mechanical energy, burst-and-coast swimming does not actually save energy comparing with steady swimming at the same average speed, in that frequently changing of speed leads to decrease of efficiency.

Population status, threats and conservation of the Yangtze finless porpoise

The Yangtze finless porpoise (Neophocaena phocaenoides asiaeorientalis) is currently limited to the middle and lower reaches of the Yangtze River from Yichang to Shanghai, China, and the adjoining Poyang and Dongting Lakes. Its population size has decreased remarkably during the last several decades due to the heavy impact of human activities, including overfishing of prey species, water development projects that cause attendant habitat loss and degradation, water pollution, and accidental deaths caused by harmful fishing gear and collisions with motorized vessels. It was estimated that the number of remaining individuals was down to approximately 1800 in 2006, a number that is decreasing at a rate as high as 5% per year. Three conservation measures - in situ and ex situ conservation and captive breeding have been applied to the protection of this unique porpoise since the early 1990s. Seven natural and two "semi-natural" reserves have so far been established. Since 1996, a small group of finless porpoises has been successfully reared in a facility at the Institute of Hydrobiology of the Chinese Academy of Sciences; three babies were born in captivity on July 5, 2005, June 2, 2007 and July 5, 2008. These are the first freshwater cetaceans ever born in captivity in the world. Several groups of these porpoises caught in the main stream of the Yangtze River, or rescued, have been introduced into the Tian'e-Zhou Semi-natural Reserve since 1990. These efforts have proven that, not only can these animals survive in the area, they are also to reproduce naturally and successfully. More than 30 calves had been born in the reserve since then, with one to three born each year. Taking deaths and transfers into account, there were approximately 30 individuals living in the reserve as of the end of 2007. Among eight mature females captured in April 2008, five were confirmed pregnant. This effort represents the first successful attempt at off-site protection of a cetacean species in the world, and establishes a solid base for conservation of the Yangtze finless porpoise. A lesson must be drawn from the tragedy of Chinese River Dolphin (Lipotes vexillifer), which has already been declared likely extinct. Strong, effective and appropriate protective measures must be carried out quickly to prevent the Yangtze finless porpoise from becoming a second Chinese River Dolphin, and save the biodiversity of the Yangtze River as a whole.

Applications of factor-criteria system reconstruction analysis in the reproduction research on grass carp, black carp, silver carp and bighead in the Yangtze River

The natural reproduction of grass carp, black carp, silver carp, and bighead will be affected adversely by the Three Gorges Project in the Yangtze River. One of the methods to save the fish is to regulate the water levels, keeping them suited for the species to spawn. Nine factors associated with the scale of larvae-flood of the four species are classified into five levels, and the ranges of these factors producing larvae-floods are given by using the "factor-criteria system reconstruction analysis" method. Moderate beginning water levels and flow, with high daily increases in the rate of water level and flow, and a long duration of water level rising are important for the production of a large larvae-flood.

A Complex BPF with On Chip Auto-tuning Architecture for Wireless Receivers

A 3(rd) order complex band-pass filter (BPF) with auto-tuning architecture is proposed in this paper. It is implemented in 0.18um standard CMOS technology. The complex filter is centered at 4.092MHz with bandwidth of 2.4MHz. The in-band 3(rd) order harmonic input intercept point (IIP3) is larger than 16.2dBm, with 50 Omega as the source impedance. The input referred noise is about 80uV(rms). The RC tuning is based on Binary Search Algorithm (BSA) with tuning accuracy of 3%. The chip area of the tuning system is 0.28 x 0.22 mm(2), less than 1/8 of that of the main-filter which is 0.92 x 0.59 mm(2). After tuning is completed, the tuning system will be turned off automatically to save power and to avoid interference. The complex filter consumes 2.6mA with a 1.8V power supply.

A Complex BPF with On Chip Auto-tuning Architecture for Low-IF Receivers

A 3(rd) order complex band-pass filter (BPF) with auto-tuning architecture is proposed in this paper. It is implemented in 0.18 mu m standard CMOS technology. The complex filter is centered at 4.092MHz with bandwidth of 2.4MHz. The in-band 3(rd) order harmonic input intercept point (IIP3) is larger than 19dBm, with 50 Omega as the source impedance. The input referred noise is about 80 mu V-rms. The RC tuning is based on Binary Search Algorithm (BSA) with tuning accuracy of 3%. The chip area of the tuning system is 0.28x0.22mm(2), less than 1/8 of that of the main-filter which is 0.92x0.59mm(2). After tuning is completed, the tuning system will be turned off automatically to save power and to avoid interference. The complex filter consumes 2.6mA with a 1.8V power supply.

小麦实时控制灌溉的土壤水分含量探头合理埋设深度研究

利用室内控制试验研究了根据不同深度土壤水分传感器灌溉处理对冬小麦生物学性状及水分利用率等的影响。结果显示,以10 cm探头控制灌溉最为省水,同时冬小麦生物学性状及水分利用率等最佳。由于试验冬小麦处于生育前期,随着小麦生育期延伸,当根系超过30 cm深度时,根系吸水的深度增加,探头的埋设深度需要田间试验进行更详细的研究。

A multi-standard active-RC filter with accurate tuning system

A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architec-ture is presented. It exhibits 1EEE 802. 11a/b/g (9.5 MHz) and DVB-H (3 MHz, 4 MHz) application. The filter exploits digitally-controlled polysilicon resistor banks and a phase lock loop type automatic tuning system. The novel and complex automatic frequency calibration scheme provides better than 4 comer frequency accuracy, and it can be powered down after calibration to save power and avoid digital signal interference. The filter achieves OIP3 of 26 dBm and the measured group delay variation of the receiver filter is 50 ns (WLAN mode). Its dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from a 2.85 V supply. The dissipation of calibration consumes 2 mA. The circuit has been fabricated in a 0.35μm 47 GHz SiGe BiCMOS technology; the receiver and transmitter filter occupy 0.21 mm~2 and 0.11 mm~2 (calibration circuit excluded), respectively.

Applicatioo of Pade Approximation in Simulating Photonic Crystals

To save finite-difference time-domain(FDTD) computing time, several methods are proposed to convert the time domain FDTD output into frequency domain. The Padé approximation with Baker's algorithm and the program are introduced to simulate photonic crystal structures. For a simple pole system with frequency 160THz and quality factor of 5000,the intensity spectrum obtained by the Padé approximation from a 28-item sequence output is more exact than that obtained by fast Fourier transformation from a 220-item sequence output. The mode frequencies and quality factors are calculated at different wave vectors for the photonic crystal slab from a much shorter FDTD output than that required by the FFT method,and then the band diagrams are obatined. In addition,mode frequencies and Q-factors are calculated for photonic crystal microcavity.

Design,Fabrication,and Testing of Single-Side Alignment of 16×0.8nm Arrayed-Waveguide Grating

A novel design of 100GHz-spaced 16channel arrayed-waveguide grating (AWG) based on silica-on-silicon chip is reported.AWG is achieved by adding a Y-branch to the AWG and arranging the input/output channel in a neat row,so the whole configuration can be aligned and packaged using only one fiber-array.This configuration can decrease the device's size,enlarge the minimum radius of curvature,save time on polishing and alignment,and reduce the chip's fabrication cost.

Simulation of micromegas detector by garfield program

In this paper, a batch file which describes the detailed structure and the corresponding physical process of Micro-Mesh Gaseous Structure (Micromegas) detector, the macro commands and the control structures based on the Garfield program has been developed. And using the Garfield program controlled by this batch file, the detector's gain and spatial resolution have been investigated under different conditions. These results obtained by the simulation program not only exhibit the influences of the mesh and drift voltage, the mixture gas proportion, the distance between the mesh cathode and the printed circuit board readout anode, and the Lines Per Inch of the mesh cathode on the gain and spatial resolution of the detector, but also are very important to optimize the design, shorten the experimental period, and save cost during the detector development. Additionally, they also indicate that the Garfield program is a powerful tool for the Micromegas detector design and optimization.

陕北丘陵沟壑区经济林果发展战略

陕北丘陵沟壑区经济林果发展 ,必须抓好建设规划 ,加强坡地经济林果的集流节水保墒和科技宣传 ,创建自己的市场 ,才能解决好植被建设和经济发展这个问题

混凝土薄壳球形水窖结构的优化设计

分析球形水窖空间结构的应力分布情况并进行几何尺寸优化,避免建设者根据经验来确定球形水窖的厚度、构造及混凝土标号,以节省建窖材料,同时防止应力不足而发生破坏。【方法】利用基于ANSYS平台新开发的窖体有限元分析软件,对实际中窖壁厚度为4和11 cm的混凝土薄壳球形水窖进行空间结构应力分析,同时以水窖耗材量最小为目标函数,以许用应力和变形量为约束条件,对其进行几何尺寸优化。【结果】计算得出窖壁厚度为4和11 cm的水窖最大拉应力分别为1 380.00和447.31 kPa,最大压应力分别为5 153.20和1 896.70 kPa;优化出空窖不利工况下容积为20,30和40 m3的球形水窖窖壁最佳厚度,即栗钙土地区分别为0.051,0.061和0.065m,黄土地区分别为0.050,0.059和0.062 m。【结论】经软件优化计算后的球形水窖结构,既能满足强度和刚度的要求,同时也最大限度地节约了材料用量;利用新开发的窖体结构优化分析软件,能够对球形水窖进行空间应力分析与结构优化,可以作为球形水窖设计软件。

一种面向无线传感器网络协同任务分配的动态联盟更新机制

在面向目标追踪等应用的无线传感器网络研究中,协同任务分配机制的研究是很重要的。基于动态联盟机制的协同任务分配方法是事件触发的,适用于任务出现频率相对较低的大规模无线传感器网络。本文在基于动态联盟机制研究的基础上,首先引入了联盟覆盖范围和休眠盟员的概念,进一步消除针对同一任务的检测传感器节点的冗余,降低系统的能量消耗;而后又给出了一种动态联盟的更新机制,以保证动态联盟执行任务时的连续性,在一定程度上保证网络的检测性能。最后通过仿真,从系统总能耗、目标捕获率和检测误差标准差等方面检验了算法的性能,并给出了缓冲带宽度等参数对能耗和网络检测性能的影响。

深水滑翔机器人耐压壳体结构优化设计

针对深水滑翔机器人耐压壳体在深水中压缩变形和海水密度随水深增大而变化等因素造成驱动浮力变化问题,利用压缩变形和密度变化对驱动浮力影响的互补特性,归纳了载体耐压壳体结构优化设计方法。保证耐压壳体抗压条件和质量最小前提下采用结构优化设计方法,降低耐压壳体压缩变形和海水密度变化对驱动浮力的影响,提高系统能源的利用率。