Catalytic Cracking and Heat Sink Capacity of Aviation Kerosene Under Supercritical Conditions

Catalytic cracking of China no. 3 aviation kerosene using a zeolite catalyst was investigated under supercritical conditions. A three-stage heating/cracking system was specially designed to be capable of heating 0.8 kg kerosene to a temperature of 1050 K and pressure of 7.0 MPa with maximum mass flow rate of 80 g/s. Sonic nozzles of different diameters were used to calibrate and monitor the mass flow rate of the cracked fuel mixture. With proper experiment arrangements, the mass flow rate per unit throat area of the cracked fuel mixture was found to well correlate with the extent of fuel conversion. The gaseous products obtained from fuel cracking under different conditions were also analyzed using gas chromatography. Composition analysis showed that the average molecular weight of the resulting gaseous products and the fuel mass conversion percentage were a strong function of the fuel temperature and were only slightly affected by the fuel pressure. The fuel conversion was also shown to depend on the fuel residence time in the reactor, as expected. Furthermore, the heat sink levels due to sensible heating and endothermic cracking were determined and compared at varying test conditions. It was found that at a fuel temperature of similar to 1050 K, the total heat sink reached similar to 3.4 MJ/kg, in which chemical heat sink accounted for similar to 1.5 MJ/kg.

Thermal cracking of aviation kerosene for scramjet applications

Thermal cracking of China No.3 aviation kerosene was studied experimentally and analytically under supercritical conditions relevant to regenerative cooling system for Mach-6 scramjet applications. A two-stage heated tube system with cracked products collection/analysis was used and it can achieve a fuel temperature range of 700-1100 K, a pressure range of 3.5-4.5 MPa and a residence time of approximately 0.5-1.3 s. Compositions of the cracked gaseous products and mass flow rate of the kerosene flow at varied temperatures and pressures were obtained experimentally. A one-step lumped model was developed with the cracked mixtures grouped into three categories: unreacted kerosene, gaseous products and residuals including liquid products and carbon deposits. Based on the model, fuel conversion on the mass basis, the reaction rate and the residence time were estimated as functions of temperature. Meanwhile, a sonic nozzle was used for the control of the mass flow rate of the cracked kerosene, and correlation of the mass flow rate gives a good agreement with the measurements.

农牧交错区主要植物的氮素利用效率

Berendse&Aerts (1987)认为氮素利用效率(nitrogen use efficiency，NUE)可以分为两部分的乘积，即：①氮素生产力(nitrogen productivity，NP)，②氮素的平均滞留时间(mean residencetime，MRT)。本文利用这一概念对处于我国北方农牧交错带的内蒙古自治区多伦县典型植物的氮素利用策略进行了研究。研究假设：植物在贫瘠生境上所采取的氮素适应策略主要是提高对所吸收氮素的保持能力(较长的MRT)，而不是提高NUE。 在不同土壤生境上，属于不同生活型的不同物种其NP和MRT之间存在负相关关系。在不同生境、生活型和物种之间，作为NP与MRT乘积的NUE比NP、MRT的变化相对要小，结果表明植物主要通过延长MRT来适应氮素贫瘠的生境。因为NP与MRT相反的方向变化，二者不能同时增加或减少，所以NP与MRT之间存在相互协调(trade-off)的关系。 在群落和生态系统水平上，NP与MRT之间也存在相互协调关系，不同水平上的NUE之间也存在一定的联系。除了在种间存在这种关系外，通过对多伦县和十三里滩两种针茅（大针茅、克氏针茅）的氮素利用特征的研究，发现在种内，NP与MRT之间也存在这种相互协调关系。NUE与土壤供氮能力有关，随着土壤供氮能力的下降，NUE呈上升趋势。植物的NUE不仅与土壤的供氮能力有关，其它因素如土壤水分供应状况也会对植物的NUE产生影响，例如，与生长在河岸上的植物相比，生长在河滩湿地上的植物具有较高的NP，但MRT却较低。在群落中，不同植物个体的NUE及其组成参数NP和MRT也存在较大的差异，较大的植株具有较高的NP和MRT，因而NUE也高于个体较小的植株。本文研究结果表明，植物的NUE与氮素回收转移特性密切相关，植物提高氮素回收效率(nitrogen resorption efficiency，NRE)可以延长MRT，从而提高NUE。

Budgets and dynamics of nitrogen and phosphorus in a shallow, hypereutrophic lake in China

Budgets and dynamics of nitrogen and phosphorus in Lake Donghu were investigated from Oct. 1997 to Sept. 1999. The water residence time was estimated to be 89 days in 1997-1998 and 124 days in 1998-1999. The total external loadings were 53 g N m(-2) yr(-1) and 3.2 g P m(-2) yr(-1) in 1997-1998, and 42 g N m(-2) yr(-1) and 3.1 g P m(-2) yr(-1) in 1998-1999. On average, about 80% of nitrogen and phosphorus input was from sewage outlets, while the rest was from land runoff and precipitation. Ammonium ion was the most abundant form of inorganic nitrogen in the sewage. The nutrient output was mainly through water outflow and fish catch. The percentages of nutrients in fish were estimated to be 7.8%-11.2% for nitrogen and 47.6%- 49.6% for phosphorus. Lake Donghu has a very high nutrient retention (63% for nitrogen and 79% for phosphorus) mainly due to its closure and long water residence time. Sedimentation is an important nutrient retention mechanism in this lake. Using mass balance method, we estimated that denitrification of Lake Donghu involves about 50% of the retained nitrogen. Lake Donghu is rich in inorganic nitrogen and phosphorus and showed great seasonal variation.

Development of a self-thermal insulation miniature combustor

A novel miniature cylindrical combustor, whose chamber wall is made of porous material, has been designed and experimented for reducing heat loss and enhancing flame stability. The combustor has the function of reducing wall heat loss, extending residence time and avoiding radical chemical quenching with a self-thermal insulation concept in which heat loss reduction is obtained by the opposite flow directions between thermal energy transfer and mass flow. The methane/air mixture flames formed in the chamber are blue and tubular in shape. Between the flames and the porous wall, there is a thin unburned film that plays a significant role in reducing the flames' heat loss and keeping the flames stable. The porous wall temperature was 150-400 degrees C when the temperatures of the flames and exhaust gas were more than 1200 degrees C. When the equivalence ratio phi < 1.0, the methane conversion ratio was above 95%; the combustion efficiency was near 90%; and the overall sidewall heat loss was less than 15% in the 1.53 cm(3) chamber. Moreover, its combustion efficiency is stable in a wider combustion load (input power) range.

The design and operation of a new clapboard-type internal circulating fluidized-bed gasifier

The design and operation of a new clapboard-type internal circulating fluidized-bed gasifier is proposed in this article. By arranging the clapboard in the bed, the gasifier is thus divided into two regions, which are characterized by different fluidization velocities. The bed structure is designed so that it can guide the circulating flow passing through the two regions, and therefore the feedstock particles entrained in the flow experience longer residence time. The experimental results based on the present new design, operating in the temperature range of 790 degrees C-850 degrees C, indicate that the gas yield is from 1.6-1.9 Nm(3)/kg feedstock, the gas enthalpies are 5,345 kJ/Nm(3) for wood chip and 4,875 kJ/m(3) for rice husk, and a gasification efficiency up to 75% can be obtained.

Study on the technology of thermal cracking of paraffin to alpha olefins

Alpha olefins are mainly produced from paraffin cracking in China, but their quality is not good because of bad quality of cracking feed and outdated technology. The technology of paraffin once-through cracking, paraffin recycle cracking of removing the heavy fraction after wax vaporizing and that of removing the heavy fraction before wax vaporizing were investigated in this paper. It was found that the technology of paraffin recycle cracking of removing the heavy fraction before wax vaporizing is new and better under the same operating conditions. Using hard paraffin (mp 54-56 degrees C) as feed, the high-quality alpha olefins products (C-5-C-21) containing more than 97 wt% of olefins and more than 88 wt% of alpha olefins are produced under optimum process conditions, which are a steam to paraffin ratio of 15 wt%, process temperature of 600 degrees C, low hydrocarbon partial pressure and residence time of 2 s. In addition, with the technology of the second injecting steam in ethylene cracking used in paraffin cracking, producing coke in paraffin cracking furnace has been markedly reduced.

Performance of supersonic model combustors with staged injections of supercritical aviation kerosene

Supersonic model combustors using two-stage injections of supercritical kerosene were experimentally investigated in both Mach 2.5 and 3.0 model combustors with stagnation temperatures of approximately 1,750 K. Supercritical kerosene of approximately 760 K was prepared and injected in the overall equivalence ratio range of 0.5-1.46. Two pairs of integrated injector/flameholder cavity modules in tandem were used to facilitate fuel-air mixing and stable combustion. For single-stage fuel injection at an upstream location, it was found that the boundary layer separation could propagate into the isolator with increasing fuel equivalence ratio due to excessive local heat release, which in turns changed the entry airflow conditions. Moving the fuel injection to a further downstream location could alleviate the problem, while it would result in a decrease in combustion efficiency due to shorter fuel residence time. With two-stage fuel injections the overall combustor performance was shown to be improved and kerosene injections at fuel rich conditions could be reached without the upstream propagation of the boundary layer separation into the isolator. Furthermore, effects of the entry Mach number and pilot hydrogen on combustion performance were also studied.

制革废水生物强化处理及中水回用试验研究

制革行业是轻工行业中仅次于造纸业的高耗水、重污染行业，作为劳动密集型行业，在解决大量人口就业问题的同时，也对所在地区环境造成了严重污染。目前我国制革行业每年排放废水8,000~12,000万吨，废水中含铬约3,500 t，SS为1.2×105 t，COD为1.8×105 t，BOD为7×104 t，对水体污染严重。 本研究在对厌氧酸化工艺进行研究、一级好氧处理段进行工艺比选研究的基础上，获得了匀质调节—SBBR—BAF的生物处理工艺，并依托该工艺进行了生物强化处理的研究，考察了菌剂的强化运行效果及其处理水回用的可行性。 研究表明，在进水COD＞3,000 mg/L，厌氧酸化具有很好的抗冲击作用，保证了好氧工艺出水COD＜200 mg/L；在进水COD＜3,000 mg/L，可只通过好氧处理实现出水COD＜200 mg/L。厌氧酸化停留时间选择不当，会导致厌氧出水硫化物浓度升高，严重影响好氧系统，会使好氧活性污泥因中毒而解絮。 研究表明，当进水COD为2,000~2,500 mg/L，NH4+-N为130~146 mg/L时，COD、NH4+-N去除率SBBR分别为93.8%~96.6%和14.5%~55.9%，SBR分别为88.8%~94.9%和13%~50.7%，表明SBBR优于SBR。同时，研究发现SBBR污泥增长率为0.05 kgVSS/kgCOD，仅为SBR0.57 kgVSS/kgCOD的8.8%。此外，研究发现SBBR在停止运行后经3个运行周期可回复原油能力，而SBR池经9个周期培养也不能恢复，说明SBBR恢复能力明显优于SBR。 研究表明，以匀质调节—SBBR—BAF为主的制革废水处理工艺，出水水质稳定，进水COD 801~2,834 mg/L、NH4+-N 87~203 mg/L，出水COD＜80 mg/L、NH4+-N＜10 mg/L，基本达到中水回用标准；操作简单灵活，没有污泥回流系统，污泥产率低，污泥处理费用低；工艺基本不需要添加化学药剂，既节约成本、又避免了二次污染；两级生物膜使得该工艺具有很强的耐冲击负荷能力，特别适合制革废水水质水量波动大的特点。 研究表明，高效菌对系统的启动具有一定的促进作用，强化系统生物膜6天可以成熟，对照系统生物膜9天可以成熟。同时高效菌能加速COD降解，缩短停留时间，强化系统6~8 h可使COD＜200 mg/L，对照系统8~10 h可使COD＜200 mg/L。长期运行表明，强化系统的SBBR在COD和NH4+-N的去除率都优于对照系统的SBBR。最终出水COD强化系统平均为53 mg/L、对照系统为74 mg/L。在模拟循环过程中，强化系统均有更高的稳定性。可实现8次理论循环，而对照系统只能实现4次理论循环。 研究表明，通过合理的工艺设计，可以实现猪皮制革废水达到《污水综合排放标准GB8976-1996》一级标准，同时满足工厂部分用水要求。通过添加高效微生物，可提高生物处理系统处理能力，使处理水能够满足工厂的多次回用。 As a labour-intensive industry, tanning has created large amount of working opportunities as well as caused severe contamination to environment. And it is one of the highest water-consuming and polluting industry, only second to manufacturing. At present time, Chinese leather industry emits wastewater about 80,000,000~120,000,000 t annually, which contains chromium about 3,500 t, SS 1.2×105 t, COD 1.8×105 t, BOD 7×104 t and ambient riverhead has been polluted greatly. Based on the research of anaerobic acidification and comparison of SBBR and SBR, biotreatment process (Homogenization—SBBR—BAF) had been established to amend the disadvantages of traditional sewage treatment such as too much sludge, high cost of advanced treatment and NH4+-N can not reach the emission standard. Research on the bioaugmentation was also been carried out. Researches showed, when COD of influent was beyond 3,000 mg/L, anaerobic acidification could resist strong impact, thus COD of effluent was less than 200 mg/L; when COD of influent was less than 3,000 mg/L, only throughout aerobic sewage treatment could COD of effluent beless than 200 mg/L. False residence tiome of anaerobic acidification would lead to the higher effluent concentration of sulfide and disintegration of aerobic activated sludge. Researches showed SBBR worked a better than SBR: when influent between 2,000 and 2,500 mg/L, NH4+-N between 130 mg/L and 146 mg/L, COD, NH4+-N removal rate of SBBR was 93.3%~96.6%, 14.5%~55.9% respectively while COD, NH4+-N removal rate of SBR was 88.8%~94.9%, 13%~50.7% respectively. Sludge growth rate of SBBR was 8.8% of that of 0.05 kgVSS/kgCOD. Besides, SBBR could recovered after 3 operating periods while SBR worked no better after 9 operating periods.Therefore, SBBR excelled SBR. Researches showed, effluent quantity of tannery wastewater treatment process (Homogenization—SBBR—BAF) was stable. When COD of influent was between 801 and 2,834 mg/L, NH4+-N was between 87 mg/L and 203 mg/L, COD of effluent was less than 80 mg/L, NH4+-N was less than 10 mg/L, which achieved the standard of reuse. This biotreatment was featured in low cost, easy and flexible management, less sludge, no inverse sludge system. Besides, this technique required no chemical, which could lower the cost and avoid secondary pollution. Great resistant of impact due to two membranes and was suitable for tannery wastewater which was featured by fluctuation of influent quality and quantity. Researches showed effective microorganisms promotes the startup of the process.Biofilm in the bioaugmentation process matured with 6 days while biofilm in normal process matured with 9 days. Effective microorganisms could accelerate the degradation of COD and shorten the residence time. Aggrandizement system could make COD<200 mg/L with 6 to8 hours while cntrolling system could make COD<200 mg/L with 8 to 10 hours. Long-term operating shows that SBBR in the bioaugmentation system worked better than the normal system in the treatment of COD and NH4+-N. The average COC of effluent in bioaugmentation system was 53 mg/L, normal system was 74 mg/L. In the simulative circulation process,aggrandizement process, which could fulfill 8 times theoretical circulation, works more stably than controlling process which could only fulfill 4 times theoretical circulation. Researches showed that reasonable design could make the wastewater meet the first grade of discharging standard of National Integrated Wastewater Discharge Standard (GB8976-1996), and partially meet the demand of water using of the factory. Adding effective microorganisms could enhance the biotreatment and make the effluents reuse many times.

Experimental study of the beta-delayed proton decays of Er-145,Er-147

The beta-delayed proton decays of Er-145,Er-147 have been studied experimentally using the Ni-58 + Mo-92 reaction at beam energy of 383 MeV. On the basis of a He-jet apparatus coupled with a tape transport system, the beta-delayed proton radioactivities both from the nu s(1/2) ground state and the nu h(11/2) isomer in Er-145,Er-147 were observed by proton-gamma coincidence measurements. By analyzing the time distributions of the 4(+) -> 2(gamma)(+) transitions in the granddaughter nuclei Dy-144,Dy-146, the half-lives of 1.0 +/- 0.3 s and 1.6 +/- 0.2 s have been deduced for the nu h(11/2) isomers in Er-145,Er-147, respectively.

Relationships between precipitation, soil water and groundwater at Chongling catchment with the typical vegetation cover in the Taihang mountainous region, China

Vegetation cover plays an important role in the process of evaporation and infiltration. To explore the relationships between precipitation, soil water and groundwater in Taihang mountainous region, China, precipitation, soil water and water table were observed from 2004 to 2006, and precipitation, soil water and groundwater were sampled in 2004 and 2005 for oxygen-18 and deuterium analysis at Chongling catchment. The soil water was sampled at three sites covered by grass (Carex humilis and Carex lanceolata), acacia and arborvitae respectively. Precipitation is mainly concentrated in rainy seasons and has no significant spatial variance in study area. The stable isotopic compositions are enriched in precipitation and soil water due to the evaporation. The analysis of soil water potential and isotopic profiles shows that evaporation of soil water under arborvitae cover is weaker than under grass and acacia, while soil water evaporation under grass and acacia showed no significant difference. Both delta O-18 profiles and soil water potential dynamics reveal that the soil under acacia allows the most rapid infiltration rate, which may be related to preferential flow. In the process of infiltration after a rainstorm, antecedent water still takes up over 30% of water in the topsoil. The soil water between depths of 0-115 cm under grass has a residence time of about 20 days in the rainy season. Groundwater recharge from precipitation mainly occurs in the rainy season, especially when rainstorms or successive heavy rain events happen.

Chain propagation kinetics on melt grafting reaction

Graft copolymerization in the molten state is of fundamental importance as a probe of chemical modification and reactive compatibilization. However, few grafting kinetic studies on reactive extrusion have been carried out because of the inherent difficulties, as expected. In this work, we have studied chain propagation kinetics on melt grafting using pre-irradiated linear low density polyethylene (LLDPE) and three monomers, acrylic acid (AA), methacrylic acid (MAA), and methyl methacrylate (MMA), as the model system. We measured the apparent chain propagation rate coefficients of grafting (k(p,g)) and homopolymerization (k(p,h)) at an initial stage for the melt grafting by FT-IR spectroscopy and electron spin resonance spectroscopy. It was observed that the convective mixing affected the rate coefficients. The magnitude of k(p,h) and k(p,g) were in the same order, but k(p,h) was slightly larger than k(p,g) The k(p,g) of the three grafting systems increased in the order: LLDPE/MMA < LLDPE/MAA < LLDPE/AA. These results are explained in terms of phase separation, solubility, and inherent reactivity of the monomer.

An evaluation of gadolinium polyoxornetalates as possible MRI contrast agent

Two gadolinium polyoxometalates, K9GdW10O36 and K-11 [Gd(PW11O39)(2)], have been evaluated both in vivo and in vitro as candidates for tissue-specific MRI contrast agents. T-1-relaxivities of 6.89 mM(-1) . s(-1) for K9GdW10O36 and 5.27 mM(-1) . s(-1) for K-11[Gd(PW11O39)(2)] are slightly higher than that of the commercial MRI contrast agent (Gd-DTPA). Both compounds bind with bovine serum albumin and human serum transferrin and favorable liver-specific contrast enhancement in in vivo MRI with Sprague-Dawley rats after i.v. administration has been demonstrated. Imaging studies demonstrate that the two agents have a long residence time, showing MR signal enhancement in the liver for more than 40 min, longer than commercially available contrast agents. In vivo and in vitro assays showed that GdW10 and Gd(PW11)(2) are promising liver-specific MRI contrast agents and GdW10 may be used in the diagnosis of the pathological state. However, with the higher acute toxicity, the two gadolinium polyoxometalates need to be modified and studied further before clinical use.

Efforts to decrease crosslinking extent of polyethylene in a reactive extrusion grafting process

Grafting of acrylic acid and glycidyl methacrylate onto low density polyethylene (LDPE) was performed by using a corotating twin-screw extruder. The effects of residence time and concentration of initiator and monomers on degree of grafting and gel content of grafting LDPE were studied systematically. Paraffin, styrene, p-benzoquinone, triphenyl phosphite, tetrachloromethane, and oleic acid were added to try to decrease the extent of crosslinking of LDPE. 4-hydroxyl-2,2,6,6-tetramethyl-1-piperidinyloxy (4-hydroxyl-TEMPO) and dipentamethylenethiuram tetrasulfide were also tried to inhibit crosslinking reaction of LDPE during its extruding grafting process. It was found that p-benzoquinone, triphenyl phosphite and tetrachloromethane were good inhibitors for crosslinking of LDPE. (C) 2000 John Wiley & Sons, Inc.

Periodical mixing of MORB magmas near East Pacific Rise 13N: evidence from modeling and zoned plagioclase phenocrysts

Thirty-six basalt samples from near East Pacific Rise 13N are analyzed for major and trace elements. Different types of zoned plagioclase phenocrysts in basalts are also backscatter imaged, and major element profiles scanned and analyzed for microprobe. Basalts dredged from a restricted area have evolved to different extents (MgO=9.38wt%-6.76wt%). High MgO basalts are modeled for crystallization to MgO of about 7wt%, and resulted in the Ni contents (28 ppm) that are generally lower than that in observed basalts (> 60 ppm). It suggests that low MgO basalts may have experienced more intensive magma mixing. High MgO (9.38wt%) basalt is modeled for self-"mixing-crystallization", and the high Ni contents in low MgO basalts can be generated in small scale and periodical self-mixing of new magma (high MgO). "Mixing-crystallization" processes that low MgO magmas experienced accord with recent 226Ra/230Th disequilibria studies for magma residence time, in which low MgO magmas have experienced more circles of "mixing-crystallization" in relatively longer residence time. Magma mixing is not homogeneous in magma chamber, however, low MgO magmas are closer to stable composition produced by periodical "mixing-crystallization", which is also an important reason for magma diversity in East Pacific Rise. Zoned plagioclase phenocrysts can be divided into two types: with and without high An# cores, both of which have multiple reversed An# zones, suggesting periodical mixing of their host magmas. Cores of zoned plagioclase in low MgO (7.45wt%) basalt differ significantly with their mantle in An#, but are similar in An# with microlite cores (products of equilibrium crystallization) in high MgO (9.38wt%) basalt, which further shows that plagioclase phenocryst cores in low MgO basalts may have formed in their parental magmas before entering into the magma chamber.