从60MeV/u~(18)O离子辐照过的钍中分离Ra

对以212Pb, 133Ba和224Ra作示踪剂,(NH4)2H2EDTA为淋洗剂,用阳离子交换法从Pb、Ba中分离Ra的工艺条件做了研究。提出了一个从60 MeV/u 18O离子辐照过的ThO2靶中分离Ra的放射化学流程。实验结果表明,该流程对主要反应产物,特别是Ba的去污较好,Ra的产额可达70%以上。

Production cross-section of Ra-230 in the reaction of 60 MeV/u O-18 ions with U-238

A thick natural uranium target was bombarded with a 60 MeV/u O-18 beam. The neutron-rich isotope Ra-230 as the target residue was produced through the multinucleon transfer reaction (U-238-4p-4n). The barium and radium fraction as BaCl2 precipitate were radiochemically separated first from the mixture of uranium and reaction products. Then, the radium fraction was separated from BaCl2 precipitate by using cation exchange technique. The gamma-ray spectra of the Ra fraction were measured using an HPGe detector. The production cross sections of Ra-230 were obtained by a combination of the radiochemical separation technique and off-line gamma-ray spectroscopy. The cross section of Ra-230 has been determined to be 66 +/- 20 mu b.

Characterization of Air-Water Two-Phase Vertical Flow by Using Electrical Resistance Imaging

The characterization of air-water two-phase vertical flow in a 12 m flow loop with 1.5 m of vertical section is studied by using electrical resistance tomography (ERT). By applying a fast data collection to a dual-plane ERT sensor and an iterative image reconstruction algorithm, relevant information is gathered for implementation of flow characteristics, particularly for flow regime recognition. A cross-correlation method is also used to interpret the velocity distribution of the gas phase on the cross section. The paper demonstrates that ERT can now be deployed routinely for velocity measurements and this capability will increase as faster measurement systems evolve.

Oscillatory instability of Rayleigh-Marangoni-Bénard convection in two-layer liquid systems

The oscillatory behaviour of the Rayleigh-Marangoni-Bénard convective instability (R-M-B instability) regarding two combinations of two-layer fluid systems has been investigated theoretically and numerically. For the two-layer system of Silicone oil (10cSt) over Fluorinert (FC70), both linear instability analysis and 2D numerical simulation show that the instability of the system depends strongly on the depth ratio Hr = H1/H2 of the two-layer liquid. The oscillatory regime at the onset of R-M-B convection enlarges with reducing Γ = Ra/Ma values. In the two-layer system of Silicone oil (2cSt) over water, it loses its stability and onsets to steady convection at first, then the steady convection bifurcates to oscillatory convection with increasing Rayleigh number Ra. This behaviour was found through numerical simulation above the onset of steady convection in the case of r = 2.9, ε=(Ra-Ruc)/Rac = 1.0, and Hr = 0.5. Our findings are different from the previous study of the Rayleigh-Benard instability and show the strong effects of the thermocapillary force at the interface on the time-dependent oscillations at or after the onset of convection. We propose a secondary oscillatory instability mechanism to explain the experimental observation of Degen et al. [Phys. Rev. E, 57 (1998), 6647-6659].

Rayleigh-Bénard热对流的动理论分析

利用基于分子动理论的直接模拟Monte Carlo(DSMC)方法,研究了 Rayleigh-Bènard问题.计算中,上下平板表面温度之比固定为0.1.Kn=0.01时,随着Ra数的增大,大约在1700附近,流动从热传导状态转变为热对流状态,DSMC计算得到的下平板热流与Ra数的关系与经典实验和理论结果相符.Kn=0.05时,流动保持稳定的热传导状态,Ra数的增大并不能引发热对流现象.

Information Preservation Modeling of Rayleigh-Benard Transition from Thermal Conduction to Convection

Onset and evolution of the Rayleigh-Benard (R-B) convection are investigated using the Information Preservation (IP) method. The information velocity and temperature are updated using the Octant Flux Splitting (OFS) model developed by Masters & Ye based on the Maxwell transport equation suggested by Sun & Boyd. Statistical noise inherent in particle approaches such as the direct simulation Monte Carlo (DSMC) method is effectively reduced by the IP method, and therefore the evolutions from an initial quiescent fluid to a final steady state are shown clearly. An interesting phenomenon is observed: when the Rayleigh number (Ra) exceeds its critical value, there exists an obvious incubation stage. During the incubation stage, the vortex structure clearly appears and evolves, whereas the Nusselt number (Nu) of the lower plate is close to unity. After the incubation stage, the vortex velocity and Nu rapidly increase, and the flow field quickly reaches a steady, convective state. A relation of Nu to Ra given by IP agrees with those given by DSMC, the classical theory and experimental data.

Kinetic Study Of The Rayleigh-Benard Flows

The present paper employs the direct simulation Monte Carlo (DSMC) method to study the Rayleigh-Benard flows, where the temperature ratio of the upper to lower plate is fixed to 0.1. For a Knudsen number (Kn) of 0.01, as the Rayleigh number (Ra) increases, the flow changes from the thermal conductive state to the convective state at about Ra=1700, and the calculated relation of heat flux through the lower plate versus Ra is in good agreement with classical experimental and theoretical results. For Kn=0.05, the thermal conductive state remains stable, and the increase of Ra cannot trigger thermal instability.

MEASUREMENT OF SOLID SLURRY FLOW VIA CORRELATION OF ELECTROMAGNETIC FLOW METER, ELECTRICAL RESISTANCE TOMOGRAPHY AND MECHANISTIC MODELLING

The study presented here was carried out to obtain the actual solids flow rate by the combination of electrical resistance tomography and electromagnetic flow meter. A new in-situ measurement method based on measurements of the Electromagnetic Flow Meters (EFM) and Electrical Resistance Tomography (ERT) to study the flow rates of individual phases in a vertical flow was proposed. The study was based on laboratory experiments that were carried out with a 50 mm vertical flow rig for a number of sand concentrations and different mixture velocities. A range of sand slurries with median particle size from 212 mu m to 355 mu m was tested. The solid concentration by volume covered was 5% and 15%, and the corresponding density of 5% was 1078 kg/m(3) and of 15% was 1238 kg/m(3). The flow velocity was between 1.5 m/s and 3.0 m/s. A total of 6 experimental tests were conducted. The equivalent liquid model was adopted to validate in-situ volumetric solids fraction and calculate the slip velocity. The results show that the ERT technique can be used in conjunction with an electromagnetic flow meter as a way of measurement of slurry flow rate in a vertical pipe flow. However it should be emphasized that the EFM results must be treated with reservation when the flow pattern at the EFM mounting position is a non-homogenous flow. The flow rate obtained by the EFM should be corrected considering the slip velocity and the flow pattern.

磷酸盐激光玻璃聚（CH3）2Si（OC2H5）2防潮膜

以（CH3）2Si（OC2H5）2为前驱体，采用溶胶-凝胶与有机合成相结合的方法，制得稳定性良好的涂膜液。采用旋转涂膜法在掺钕磷酸盐激光玻璃棒端面涂制防潮膜，膜层固化后透过率达96．5％，获得的膜层表面粗糙度优良，均方根表面粗糙度（RMS）为1．659nm，平均粗糙度（RA）平均为1．321nm；在激光波长1053nm，脉冲宽度1 ns条件下膜层的激光破坏闽值可达10～14 J／cm^2。经过“神光Ⅱ”高功率激光器物理实验运行，膜层使用期为五年，并且已经在我国“神光Ⅲ”原型装置上试用。

三种兰科植物的保护遗传学研究

本研究在野外调查的基础上，采用随机扩增多态DNA (RAPD)分析和形态学方法，研究了我国三种珍稀濒危兰科植物硬叶兜兰（Paphiopedilummicranthum）、麻栗坡兜兰（P. malipoense）和独花兰（Changnienia amoena）的遗传多样性与群体遗传结构，主要结果如下： 1．采用1 2个引物对分布于我国云贵地区的4个硬叶兜兰群体共161个体进行RAPD扩增和分析，得出物种水平的多态条带百分率（PPB）为71.6%，Nci的基因多样度(h)为0.217，Shannon多样性指数（1)为0.3301;4个群体的平均多样性水平为PPB=45.2%，h=0.1457，1= 0.2204：低于远交兰花的平均水平。分子方差分析(AMOVA)表明，在总遗传变异中，群体间遗传变异占20.31%．群体内占79.69%;POPGENE给出的基因分化系数 （Gst）为0.2958;遗传分化略高于远交物种的平均水平。空间自相关分析表明，所检测的两个群体中存在明显的空间结构，基因型在群体中以不同的小斑块存在。遗传距离和空间距离不存在相关关系。 2．用于麻栗坡兜兰的RAPD引物同上，但取样范围只有贵州的2个群体共10个个体。就所研究的个体柬看，麻栗坡兜兰的遗传多样性明显低于远交兰花物种的平均水平。物种水平上，多态条带百分率(PPB)为49.5%。Nei的基因多样度（h）为0. 1174， Shannon多样性指数(I)为0.1764：在群体水平上，上述三个指标的平均值则分别为12. 75%、0.0486和0.0712，均大大低于硬叶兜兰。然而，尽管作了种种努力，麻栗坡兜兰的取样个体数量仍很少，因此所得结果可能会有误差。 3．用16个引物对分布于河南、湖北、湖南、江西4个省11个独花兰群体共216个体进行了RA PD扩增和分析，独花兰在物种水平PPB=80. 7%，h=0.197．1=0. 3116;在群体水平，上述三个指标的平均值则分别为40. 9%、0.1247和0. 1902，均低于远交兰花的平均水平。AMOVA分析表明，11个独花兰群体间的遗传变异占43.48%，群体内的占56.52%：在神农架和新宁地区内部，群体间的遗传变异分别占13.68%和49.3g%(AMOVA)。POPGENE给出的11个群体的基因分化系数(Gst)为0.3580．神农架和新宁地区内的Gst，值分别为0.1194和0.2597。可见，群体间的遗传分化明显高于远交物种的平均水平。空间自相关分析表明，独花兰的遗传变异在群体内不存在明显的空间结构。群体之间的遗传距离和空间距离不存在相关关系。 4．对独花兰7个群体形态性状的分析发现，12个形态性状在群体内均有较高的变异性，cv值变动于0.022-0.30O。庐山群体(LS)在所有性状上的平均值均为最高。营养性状和花部性状的变异性基本一致。除花葶长和花距直径与某些花部性状之间没有显著的相关关系外，各性状之间均有显著的相关性。对XN4群体的统计没有发现假磷茎数目与其他性状之间存在显著相关性。 根据以上对硬叶兜兰、麻粟坡兜兰和独花兰遗传多样性和群体遗传结构韵研究，结合其他方面的资料;对三种兰花的濒危机制进行了初步的分析。首先，人为采挖和破坏是导致这些兰花物种濒危的直接原因，尤其是麻栗坡兜兰。其次， 适宜兰花生存的生境正在只益萎缩、退化和片段化。这两方面因素的共同作用导致上述兰花群体的数目和规模日益下降，由此引发的遗传多样性降低和遗传结构的改变进一步加剧其濒危状况。对于独花兰而言，较低的繁殖能力又使其生存状态雪上加霜。针对三个物种不同的繁殖特性和遗传学状况，提出如下保护措施。(1)硬叶兜兰由于繁殖能力较强、现存个体尚多，遗传多样性损失不甚严重，因此以保护其所在的生境为基础、实施原位保护，是比较合适的保护策略。(2)麻粟坡兜兰目前受破坏程度非常严重;所剩个体很少，遗传多样性较低，已经很难进行有效的原位保护。因此;应利用迁地保护手段抢救目前尚存的个体。(3)独花兰的繁殖能力较弱，因此在保护生境和严禁采摘的基础上，可采用人工授粉等方式，提高结实率、增加繁殖效率，促使其复壮：在进行迁地保护时，则应注意不同群体间存在较大遗传变异而群体内多样性较低这一现实。

植物群落复杂性与群落结构组建的描述与分析

时间、空间格局的保持和发展及其对种群、群落和生态系统动态的影响是生态学中两个相互关联的基本课题。围绕这个中心议题作者在植物个体、种群、群落各个层次上开展了研究。 1)研究了克隆植物构型及其对资源异质性的响应，给出了描述该连续体的一个指数v：In1/ln刀．（士RA为基础，发展一种包括环境，空间格局和物种相互作用三方面因素的植物群落数量分析方法，并在种多度数据的变化中分离出这几个方面的变化。 4)以适宜度理论和草原类型理论为基础，利用草原湿润度指标k作为生境综合生态因子的一个测度，构造出草原生物的适宜度模型;给出了草原生境对草原生物适宜度的评价指标：提出了草原生境指数，生境适宜度，生境适宜度过程等新的概念。(公式从略)