Fractography and Crack Initiation of Very-High-Cycle Fatigue for a High Carbon Low Alloy Steel

Very-High-Cycle Fatigue (VHCF) is the phenomenon of fatigue damage and failure of metallic materials or structures subjected to 108 cycles of fatigue loading and beyond. This paper attempts to investigate the VHCF behavior and mechanism of a high strength low alloy steel (main composition: C-1% and Cr-1.5%; quenched at 1108K and tempered at 453K). The fractography of fatigue failure was observed by optical microscopy and scanning electron microscopy. The observations reveal that, for the number of cycles to fatigue failure between 106 and 4108 cycles, fatigue cracks almost initiated in the interior of specimen and originated at non-metallic inclusions. An “optical dark area” (ODA) around initiation site is observed when fatigue initiation from interior. ODA size increases with the decrease of fatigue stress, and becomes more roundness. Fracture mechanics analysis gives the stress intensity factor of ODA, which is nearly equivalent to the corresponding fatigue threshold of the test material. The results indicate that the fatigue life of specimens with crack origin at the interior of specimen is longer than that with crack origin at specimen surface. The experimental results and the fatigue mechanism were further analyzed in terms of fracture mechanics and fracture physics, suggesting that the primary propagation of fatigue crack within the fish-eye local region is the main characteristics of VHCF.

A field model interpretation of crack initiation and growth behavior in ferroelectric ceramics: change of poling direction and boundary condition

Strain energy density expressions are obtained from a field model that can qualitatively exhibit how the electrical and mechanical disturbances would affect the crack growth behavior in ferroelectric ceramics. Simplification is achieved by considering only three material constants to account for elastic, piezoelectric and dielectric effects. Cross interaction of electric field (or displacement) with mechanical stress (or strain) is identified with the piezoelectric effect; it occurs only when the pole is aligned normal to the crack. Switching of the pole axis by 90degrees and 180degrees is examined for possible connection with domain switching. Opposing crack growth behavior can be obtained when the specification of mechanical stress sigma(infinity) and electric field E-infinity or (sigma(infinity), E-infinity) is replaced by strain e and electric displacement D-infinity or (epsilon(infinity), D-infinity). Mixed conditions (sigma(infinity),D-infinity) and (epsilon(infinity),E-infinity) are also considered. In general, crack growth is found to be larger when compared to that without the application of electric disturbances. This includes both the electric field and displacement. For the eight possible boundary conditions, crack growth retardation is identified only with (E-y(infinity),sigma(y)(infinity)) for negative E-y(infinity) and (D-y(infinity), epsilon(y)(infinity)) for positive D-y(infinity) while the mechanical conditions sigma(y)(infinity) or epsilon(y)infinity are not changed. Suitable combinations of the elastic, piezoelectric and dielectric material constants could also be made to suppress crack growth. (C) 2002 Published by Elsevier Science Ltd.

Initiation and propagation of short fatigue cracks in a weld metal

Fatigue tests were performed using a purpose designed triangular shaped specimen to investigate the initiation and propagation of short fatigue cracks in a weld metal. It was observed that short fatigue cracks evolved from slip bands and were predominantly within ferrite grains. As the test progressed, the short crack density increased with minor changes in crack length. The growth of short cracks, in the early stage resulted mainly from coalescence with other existing cracks. The mechanism of short crack behaviour is discussed.

Direct initiation of detonation with ignition tube

Experiments of direct initiation of hydrogen-oxygen by means of a hot turbulent jet were made. Results indicate that the length of ignition tube is the dominant factor in determining the ignition capability of hot turbulent jet, and that the ignition capability of turbulence jet increases with the length of ignition tube. Because this ignition capability can meet the demands of a gas-detonation-driver shock tunnel and it doesn't require additional facilities, the hot turbulent jet initiation method can be applied to large hydrogen-oxygen detonation-driver shock tunnels. Influences of obstacles on the ignition capability were also studied. It was found that the presence of obstacles weakens the ignition capability of a hot turbulent jet.

Dynamic readout of subdiffraction-limited pit arrays with a silver superlens

Recent theoretical and experimental results suggested that the silver superlens could be constructed through controlling silver thin film thickness and preparation conditions, and applied in subdiffraction-limited optical imaging and optical lithography. In this work, we report another significant application of silver superlens-ultrahigh density optical data storage. With the silver superlens the subdiffraction-limited pit arrays on an optical disk are dynamically read out and the carrier-to-noise ratio can reach 25 dB for the thin film thickness of 46 nm. The readout laser power and readout velocity have little effect on the carrier-to-noise ratio. Additionally, in our experiment the silver thin film thickness needs to be controlled in the range from 20 to 80 nm.

On the dynamic readout of sub-diffraction-limit pit arrays with a silver thin film

Fast moving arrays of periodic sub-diffraction-limit pits were dynamically read out via a silver thin film. The mechanism of the dynamic readout is analysed and discussed in detail, both experimentally and theoretically. The analysis and experiment show that, in the course of readout, surface plasmons can be excited at the silver/air interface by the focused laser beam and amplified by the silver thin film. The surface plasmons are transmitted into the substrate/silver interface with a large enhancement. The surface waves at the substrate/silver interface are scattered by the sinusoidal pits of sub-diffraction-limit size. The scattered waves are collected by a converging lens and guided into the detector for the readout.

Laser-induced damage of Ti O2 Si O2 high reflector at 1064 nm

A high laser-induced damage threshold (LIDT) TiO2/SiO2 high reflector (HR) at 1064 nm is deposited by e-beam evaporation. The HR is characterized by optical properties, surface, and cross section structure. LIDT is tested at 1064 nm with a 12 ns laser pulse in the one-on-one mode. Raman technique and scanning electron Microscope are used to analyze the laser-induced modification of HR. The possible damage mechanism is discussed. It is found that the LIDT of HR is influenced by the nanometer precursor in the surface, the intrinsic absorption of film material, the compactness of the cross section and surface structure, and the homogeneity of TiO2 layer. Three typical damage morphologies such as flat-bottom pit, delamination, and plasma scald determine well the nanometer defect initiation mechanism. The laser-induced crystallization consists well with the thermal damage nature of HR. (C) 2008 American Institute of Physics.

植物克隆性在生态修复中的意义：鄂尔多斯高原赖草和沙鞭的案例

克隆植物通过克隆生长能够很好的适应异质性的生境。在进行植被修复的研究和实践中，注意发扬或引进具有重要资源价值的克隆植物是重要的恢复生态学思考和途径。本文主要应用实验生态学的方法，通过对鄂尔多斯高原不同克隆植物克隆性及其对水分条件的反应的比较，以及对不同克隆植物抵抗风蚀和风蚀坑修复的能力的比较，探讨克隆植物对干旱(水分条件)及风蚀的适应机制，从而对克隆植物的克隆性在生态修复中的意义进行了研究和阐述。 　　对不同水分条件下赖草(Leymus secalinus (Georgi.) Tzvel)和沙鞭(Psammochloa villosa (Trin.) Bor)克隆性的研究表明：克隆生长开始时间和克隆生长率二者与克隆植物新产生子代分株数量之间存在着显著的相关关系，说明克隆生长开始时间和克隆生长率能够作为准确评价克隆性的指标;相对于沙鞭来说，赖草具有更强的克隆性，表现在它的早的克隆生长开始时间、高的克隆生长率，并且这种差异可以被水分条件所修饰;植物的克隆性对水分条件具有较强的可塑性，这种可塑性具有种间差异。相对赖草来说，沙鞭能更好地适应干旱条件。 　　克隆植物植株有两种繁殖体类型，分株和种子。本研究对分别从分株来源和种子来源的赖草与沙鞭植株在不同水分条件下生长状况及克隆性进行了比较，结果表明：水分的增加，有利于赖草的生长;而对于沙鞭来说，水分抑制了分株来源的沙鞭植株的生长，但对种子来源的沙鞭植株的生长有着促进作用。克隆植物的克隆性在水分条件较好的情况下能够得到更好的表达。不同来源有赖草植株之间克隆性没有明显差异;对于沙鞭来说，分株来源的沙鞭植株克隆性受水分条件的影响不明显，但水分有利于种子来源的沙鞭植株克隆性的表达。说明不同繁殖体类型来源的植株，克隆性对水分的反应格局存在着一定的差异。分株来源的沙鞭植株对干旱条件具有比种子来源的植株更强的适应性。 　　通过对沙鞭和赖草实生幼苗在不同风蚀程度下生长状况的比较，结果表明二者幼苗在抵抗风蚀时采取不同的策略。风蚀显著降低了赖草产生新生分株的能力，而对沙鞭潜在分株数没有显著影响。赖草实生幼苗生长状况在轻中度风蚀条件下与对照处理没有显著差异，说明对风蚀具有较强的抵抗能力，其策略可能是风险分担，赖草具有的强克隆性使之能快速产生新的子代分株，从而分担了风蚀造成的风险;沙鞭实生幼苗的生长状况受风蚀影响较为明显，但风蚀没有能对其产生潜在分株(芽)的能力产生显著的影响，说明沙鞭实生幼苗对风蚀可能采取的是通过芽的产生贮存资源、逃避风险、等待机会的策略。赖草和沙鞭对风蚀所采用的不同适应策略，可能会影响到二者在自然条件下种群更新方式的选择。 　　为了探讨克隆植物对风蚀坑修复能力及机理，研究了沙鞭和赖草对种群内风蚀坑的修复过程，结果表明：合轴型克隆草本赖草具有比单轴型克隆草本沙鞭更强的植被修复能力，能够在风蚀坑中产生更多的新生分株，这主要归功于赖草的强克隆性，而赖草间隔子的可塑性反应也有利于将更多的新生分株放置在风蚀坑内。二者进行植被修复的机理有所差异，赖草对风蚀坑的修复主要是通过周围根茎扩展进入坑中，然后产生新的分株;而沙鞭不仅可以通过周边根茎进入产生新的分株，同时也可以通过刺激深层休眠芽来产生新的分株。二者都能在风蚀坑中产生比自然条件下更多的分株，以更好利用风蚀坑中充足的光照;但同时这些分株的生长也受到风蚀坑中养分条件的制约，生物量和生长状况都不如自然条件下形成的分株。 　　 　　

Phylogeographic analysis of mitochondrial DNA haplogroup F2 in China reveals T12338C in the initiation codon of the NDS gene not to be pathogenic

In this report, we studied on a homoplasmic T12338C change in mitochondrial DNA (mtDNA), which substituted methionine in the translational initiation codon of the NADH dehydrogenase subunit 5 gene (ND5) with threonine. This nucleotide change was originall

Molecular cloning and stress-induced expression of paralichthys olivaceus heme-regulated initiation factor 2 alpha kinase

The heme-regulated initiation factor 2 alpha kinase (HRI) is acknowledged to play an important role in translational shutoff in reticulocytes in response to various cellular stresses. In this study, we report its homologous cDNA cloning and characterization from cultured flounder embryonic cells (FEC) after treatment with UV-inactivated grass carp haemorrhagic virus (GCHV). The full-length cDNA of Paralichthys olivaceus HRI homologue (PoHRI) has 2391 bp and encodes a protein of 651 amino acids. The putative PoHRI protein exhibits high identity with all members of eIF2 alpha kinase family. It contains 12 catalytic subdomains located within the C-terminus of all Ser/Thr protein kinases, a unique kinase insertion of 136 amino acids between subdomains IV and V, and a relatively conserved N-terminal domain (NTD). Upon heat shock, virus infection or Poly PC treatment, PoHRI mRNA and protein are significantly upregulated in FEC cells but show different expression patterns in response to different stresses. In healthy flounders, PoHRI displays a wide tissue distribution at both the mRNA and protein levels. These results indicate that PoHRI is a ubiquitous eIF2a kinase and might play an important role in translational control over nonheme producing FEC cells under different stresses. (c) 2006 Elsevier Ltd. All rights reserved.

Preparation of pH-sensitive polymer by thermal initiation polymerization and its application in fluorescence immunoassay

A fluorescence immunoassay for human IgG (Ag) was developed using a pH-sensitive polymer prepared by thermal initiation or redox initiation polymerization as a carrier. In the competitive immunoassay, appropriate quantity of Ag was immobilized on the polymer and the standard Ag (or sample) solution, and a constant amount of fluorescein isothiocyanate labeled goat anti-human IgG antibody (Ab-FITC) was added. Immobilized Ag and the standard (or sample) Ag competed for binding to the Ab-FITC in 37 C in homogeneous format. After changing the pH to separate the polymer-immune complex precipitate, it was re-dissolved and determined by fluorescence method. The results showed that the immobilization efficiency, immunological reaction activities of immobilized Au and phase transition pH range were improved as Ag was immobilized by thermal initiation instead of redox initiation polymerization. Under optimum conditions, the calibration graphs for the Ag in both methods, thermal initiation and redox initiation, were linear over the concentration range of 0.0-1000 ng mL(-1), with detection limits 8 (thermal initiation) and 12 ng mL(1) (redox initiation), respectively. Moreover, some pH-sensitive polymer prepared only in organic solvent or under high temperature could also be used as an immunoreaction carrier by thermal initiation polymerization. Thermal initiation polymerization was a better immobilization mode. (C) 2004 Elsevier B.V. All rights reserved.