Analysis of sulfur-containing compounds in crude oils by comprehensive two-dimensional gas chromatography with sulfur chemiluminescence detection

This paper reports an analytical method for separating, identifying, and quantifying sulfur-containing compounds in crude oil fraction (IBP-360degreesC) samples based on comprehensive two-dimensional gas chromatography coupled with a sulfur chemiluminescence detector. Various sulfur-containing compounds and their groups were analyzed with one direct injection. 3620 peaks were detected including 1722 thiols/thioethers/ disulfides/1-ring thiophenes, 953 benzothiophenes, 704 dibenzothiophenes, and 241 benzonaphthothiophenes. The target sulfur compounds and their groups were identified based on the group separation feature and structured retention of comprehensive two-dimensional gas chromatography as well as standard substances. The quantitative analysis of major sulfur-containing compounds and total sulfur was based on the linear response of the sulfur chemiluminescence detector using the internal standard method. The sulfur contents of target sulfur compounds and their groups in 4 crude oil fractions were also determined. The recoveries for standard sulfur-containing compounds were in the range of 90-102%. The quantitative result of total sulfur in the Oman crude oil fraction sample was compared with those from ASTM D 4294 standard method (total S by X-ray fluorescence spectrometry), the relative deviation (RD%) was 4.2% and the precision of the method satisfactory.

西天山造山带古生代构造演化与地壳增生—来自花岗岩和蛇绿岩的证据

The Central Asian Orogen Belt (CAOB), which is different from the subductional orogen and the collisional orogen, is known as the most important site of crustal growth in the Phanerozoic, and it has been a ‘hot spot’ for studying the orogenic belts. The Chinese West Tianshan Orogen is occupying the west-southern part of the CAOB and is of great importances to understand the orogenic processes and the continental growth in the Central Asia. The West Tianshan Orogen had undergone complex tectonic evolutional processes in Paleozoic times and large volumes granitic rocks have recorded important information about these processes. Litter is known about Phanerozoic continental growth in the Western Tianshan area so far, compared with the other areas of the CAOB, such as eastern Junggar, western Junggar, Altai and Alakol. The aim of this dissertation is to set up the chronology frame of granitoids in western Tianshan, provide new evidence for the tectonic evolution and discuss the Paleozoic continental growth in this area, on the basis of the studies on the isotopic chronology, major element, trace element and Nd-Sr isotopic geochemistry of granitoids and the isotopic chronology and geochemistry of the ophiolites in this area, especially the Kule Lake ophiolites. 25 precise SHRIMP U-Pb zircon and LA-ICPMS U-Pb zircon ages have been obtained in this dissertation. The granitic rocks in western Tianshan had been formed during two periods: the granitic gneiss with an age of 896Ma, possibly representing the forming age of the Precambrian basement; the granitic rocks with ages varying from 479Ma to 247Ma, recording the Paleozoic orogenic process of western Tianshan. The granitoids in western Tianshan are composed of intermediate-basic rocks, intermediate rocks, intermediate-acid rocks and acid rocks, mainly intermediate-acid rocks and acid rocks. They are mostly granite, granodiorite, quartz syenite and monzodiorite. Different types of granitic rocks are exposed in different tectonic units. The granitoids on the northern margin of the Yili Plate mainly formed in late Paleozoic (413Ma ~ 281Ma), those with ages varying from 413Ma to 297Ma show continental arc affinities and the magnesian calc-alkalic metaluminous diorite of 281Ma display the geochemical characteristics similar to those of granites formed during the post-orogenic period. The granitiods on the southern margin of the Yili Plate include the adakite diorite of 470Ma which was formd by partial melting of thickened lower crust, the post-collisional alkali-feldspar granite of 430Ma, the volcanic arc granite of 348Ma and the Triassic post-collisional granite. The granitoids in the Central Tianshan Plate formed in 479Ma ~ 247Ma, mainly in 433Ma ~ 321Ma. The granitic rocks with ages of 479Ma ~ 321Ma are magnesian calc-alkalic to alkalic rocks with continental arc affinities. A few post-collisional granitoids of 276Ma ~ 247Ma may have inherited the geochemical characteristics of pre-existing arc magma. The granitic rocks in Southern Tianshan (northern margin of the Tarim plate) formed two stages, 420Ma ~ 411Ma and ca. 285Ma. The magnesian calcic to alkalic granites of 420Ma ~ 411Ma may formed during the extension process of the continental margin. The granite of 285Ma includes mostly ferroan calc-alkalic to alkali-calcic rocks with high SiO2 and high alkaline contents, and obviously negative anomaly of Eu, Ba, Sr, P, Ti, similar to the geochemical characteristics of the A-type granite which is formed during post-collisional extension. The Kule Lake ophiolite in southern Tianshan shows the affinity of N-MORB. A SHRIMP zircon U-Pb age of 425±8Ma has obtained for gabbros. Some zircons have given another group of 206Pb/238U age 918Ma, which may indicate the information of the pre-exist old basement rock. The small oceanic basin represented by Kule Lake ophiolite probably developed on the split northern margin of Tarim block. A model for Paleozoic tectonic evolution of the West Tianshan Orogen has been proposed here on the basis of the new results obtained in this dissertation and the previous published data. In Early Cambrian, the Terskey Ocean occurred along the North Nalati fault (NNF), and it separated the Yili plate from the Central Tianshan plate which was probably connected with the Tarim plate. The Terskey Ocean probably subducted towards south under the Central Tianshan plate and towards north under the Yili plate simultaneously. In the early stage of Late Ordovician, the Terskey Ocean had been closed, and the Yili and Central Tianshan plates collided. Meanwhile, extension happened within the joint Central Tianshan and Tarim plates gradually and the Paleo-South Tianshan Ocean had been formed. In Early Silurian, the Paleo-South Tianshan Ocean began to subduct beneath the composite Yili-Central Tianshan plate, which was intruded by volcanic arc granitoids. In Middle Silurian, the Paleo-South Tianshan Ocean, which had reached a certain width, was subducting strongly. And this subduction may have produced voluminous granitoids in the Central Tianshan plate. In the latest stage of Carboniferous, the Paleo-South Tianshan ocean closed, and the Yili-Central Tianshan plate and Tarim plate collided. In Late Cambrian, Paleo-Junggar Ocean occurred to north of the Yili plate; and started to subduct towards south under the Yili plate in Ordovician. This subduction may have produced a magma arc on the northern margin of the Yili plate. In Late Carboniferous, the Paleo-Junggar Ocean had been closed. The Yili-Central and Junggar plates amalgamated together. The West Tianhan Orogen may undergo a post-collisional collapse since Permian. And the magmatic activities may continue to early Triassic. The initial 87Sr/86Sr ration of the granitic rocks in the western Tianshan Mountains varies from 0.703226 to 0.716343, and Nd（t）from -6.50 to 2.03. The characteristics of Sr-Nd isotope indicate that the source of granitic material is not a sole source, which may be produced by mantle-crust magma mixing. In Paleozoic time, lateral growth of the continental crust along active continental margins was dominant, whereas the vertical growth of continental crust resulted from post- collisional mantle derived magmas was not obvious.

北山及邻区古生代-早中生代增生与碰撞大地构造格局

The Beishan orogenic collage locates at the triple-joint among Xinjiang, Gansu, and Inner Mongolia Provinces, at which the Siberian, Tarim and North China plates join together. It also occupies the central segment of the southern Central Asian Orogenic Belt (CAOB). The main study area in the present suty focused on the southwest part of the Beishan Mountain, which can be subdivided into four units southernward, the Mazhongshan continental block, Huaniushan Arc, Liuyuan suture zone and Shibanshan-Daqishan Arc. 1. The Huaniushan Arc was formed by northernward dipping subduction from the Orcovician to Permian, in which volcanic rocks ranging from basic to acidic with island arc affinity were widely developed. The granitiod intrusions become smaller and younger southward, whichs indicates a southward rollback of slab. The granitiod intrusions are mainly composed of I type granites, and their geochemical compositions suggest that they have affinities of island arc settings. In the early Paleozoic（440Ma-390Ma）. The Shibanshan-Daqishan Arc, however, were produced in the southernward dipping subduction system from Carboniferous to Permian. Volcanic rocks from basic to acidic rocks are typical calcic-alkaline rocks. The granitiod intrusions become smaller and younger northernward, indicating subdution with a northernward rollback. The granitiod intrusions mainly consist of I-type granites, of which geochemical data support they belong to island arc granite. 2. Two series of adakite intrusions and eruptive rocks have been discovered in the southern margin of the Huaniushan Island Arc. The older series formed during Silurian (441.7±2.5Ma) are gneiss granitoid. These adakite granites intruded the early Paleozoic Liuyuan accretionary complex, and have the same age as most of the granite intrusions in the Huanniushan Arc. Their geochemical compostions demonstrate that they were derived from partial melting of the subudcted oceanic slab. These characteristics indicate a young oceanic crust subduction in the early Paleozoic. The late stage adakites with compositons of dacites associate with Nb-enriched basalts, and island arc basalts and dacites. Their geochemistries demonstrate that the adakites are the products of subducted slab melts, whereas the Nb-enriched basalt is products of the mantle wedge which have metasomatized by adakite melts. Such a association indicates the existences of a young ocean slab subduction. 3. The Liuyuan suture zone is composed of late Paleozoic ophiolites and two series of accretionary complexes with age of early Paleozoic. The early Paleozoic accretionary complex extensively intruded by early Palozioc granites is composed of metamorphic clastics, marble, flysch, various metamorphic igneous rocks (ultramafic, mafic and dacite), and eclogite blocks, which are connected by faults. The original compositions of the rocks in this complex are highly varied, including MORB, E-MORB, arc rocks. Geochronological study indicates that they were formed during the Silurian (420.9±2.5Ma and 421.1±4.3Ma). Large-scale granitiods intruded in the accretionary complex suggest a fast growth effect at the south margin of the Huaniushan arc. During late Paleozoic, island arc were developed on this accretionary complex. The late Paleozoic ophiolite has an age of early Permian (285.7±2.2Ma), in which the rock assemblage includes ultra-mafic, gabbros, gabbros veins, massive basalts, pillow basalt, basaltic clastic breccias, and thin layer tuff, with chert on the top.These igneous rocks have both arc and MORB affinities, indicating their belonging to SSZ type ophiolite. Therefore, oceanic basins area were still existed in the Liuyuan area in the early Permian. 4. The mafic-ultramafic complexes are distributed along major faults, and composed of zoned cumulate rocks, in which peridotites are surrounded by pyroxenite, hornblendites, gabbros norite and diorite outward. They have island-arc affinities and are consistent with typical Alaska-type mafic-ultramafic complexes. The geochronological results indicate that they were formed in the early Permian. 5. The Liuyuan A-type granite were formed under post-collisional settings during the late Triassic (230.9±2.5Ma), indicating the persistence of orogenic process till the late Triassic in the study area. Geochronological results suggested that A-type granites become younger southward from the Wulungu A-type granite belt to Liuyuan A-type granite belt, which is in good agreement with the accretionary direction of the CAOB in this area, which indicate that the Liuyuan suture is the final sture of the Paleo-Asin Ocean. 6. Structural geological evidence demonstrate the W-E spreading of main tectonic terrenes. These terrenes had mainly underwent through S-N direction contraction and NE strike-faulting. The study area had experienced a S-N direction compression after the Permian, indicating a collisional event after the Permian. Based on the evidene from sedimentary geology, paleontology, and geomagnetism, our studies indicate that the orogenic process can be subdivided into five stages: (1) the pre-orogenic stage occurred before the Ordovicain; (2) the subduction orogenic stage occurred from the Orcovician to the Permian; (3) the collisional orogenic stage occurred from the late Permian to the late Triassic; (4) the post-collision stage occurred after the Triassic. The Liuyuan areas have a long and complex tectonic evolutional history, and the Liuyuan suture zone is one of the most important sutures. It is the finally suture zone of the paleo-Asian ocean in the Beishan area.

青海德尔尼铜钴锌矿床地质构造背景与成因

The Derni large Cu-Co-Zn sulfide deposit is occurred in the Derni melange belt, which is located in the eastern section of the A'nyemaqen ophiolite melange belt. The Derni deposit is hosted in the mantle peridotites and is very special in the world. Because the studying area is of very bad natural environment and very low geological research, the geotectonic setting and genesis of the deposit have long been debated. This paper studied these two questions and answered them. The research is of great significance to reveal impotant information of deep geology, crust-mantle interaction and geotectonic evolution, to enrich theories in the study of mineral deposit and provide scientific basic data for exploration and exploit of this kind of deposit. Based on the series of new achievements and new cognitions, to start with the geologic setting of the Derni deposit, through detailed field, tectonics, petrology, geochemistry, isotopic geochronology, microfossil, and study of mineral deposit, belongs to a melange belt, including mantle peridotites slice with ore, Late Precambrian sandstone and slate slice, metamorphic rock slice. 2. Petrological and geochemical characteristics indicate that the Derni mantle peridotite is not ophiolite mantle peridotite, but is occurred under the continental crust. 3. The U-Pb isotopic age of single-grain zircon form the accumulative rock suggests that the Derni mantle peridotite were formed in 747±10Ma, and underwent a great period of metamorphic process in 441.5±2.5Ma. 4. Microfossil assemblage from the carbonaceous slate belongs to Late Precambrian. Through petrography and petrochemistry, sandstone and slate were formed in the continental margin. 5. Sideronitic texture, which is first discovered in this study, reveals the characteristics of magmatic liquation. 6. Fluid inclusion explosion temperature of pyrite is in the range of -6.15～+6.64‰, and Pb isotope is consistent with mantle peridotite, which suggest ore-forming materials are from the mantle. To sum up, the upper mantle was melting partially, when it was metasomated by the mantle fluids with abundant Cu, Co, Zn, S, Au and LREE etc. The pockets of magma became enlarged by mantle tenacity shearing, and the pockets of magma occurred magmatic differentiation in the stable field, then the magma and ore pulp together with mantle refractory remnant dirpired and crystallized in the shallow part of the crust.

阿尔金蛇绿混杂带构造岩石组合及其大地构造意义

The Alytn fault is a huge left-slip fault zone within the Asian continent, and locates such zone that is linked to main tectonic units in the western China, which makes it is very important to the tectonic framework and ore distribution in the western China. Selecting two ophiolite zones (namely Hongliugou-Lapeiquan ophiolite zone and Sulamutage ophiolite zone) respectively located within the southern and northern part of the Altyn fault and based on analysis of field geology characteristics and geochemistry, this paper recognized the rock types (mainly mafic and ultramafic rocks) within the melanges and subdivided each lithological unit based on tectonic environment. At last, this paper rebuilt the paleo-tectonic framework in the Alytn region by the method of tectonic facies and discussed its tectonic evolution with the theory of collision orogens. Combining former results with hard field observation and geochemical analysis, this paper acquired such recognitions to two ophiolte zones within the Altyn fault zone as follows: To the typical regions (Hongliugou, Lapeiquan, Mangya and Sulamutage) within the two ophiolte zones in the Altyn fault zone, this paper offered the field geology profiles. Field geology characteristics show that they are composed of melange bases (mainly abyssal flysch and carbonate rocks) and melange blocks from various tectonic environments, often with fault contact among each lithological units, belonging to typical ophiolitic melange zone. The ultramafic rocks outcropped at the Altyn region are all harzburgites. Remant grains of primary minerals have melted residual texture and elastic deformation texture under high temperature and pressure. The whole-rock analyses show their low TiO_2 contents (0.01～0.04%), low Al, Ca and high MgO contents and wide Mg~# range (89.35～95.57). Rare earth patterns have two types, namely tabacco pipe-shped and LREE-shaped, of which the former is often seen. The chondrite-nomalized Yb values of these analyses are all lower than 1. The spinels have low Ti and high Cr content and most spinels have Cr# higher than 60. All of the above characteristics show that the ultramafic rocks in the Altyn fault zone are components of metmorphic peridotites of ophiolite from depleted mantle source and most ophiolites from this zone belong to supra-subduction zone (SSZ) type ophiolite with a few mid-ocean ridge basalt (MORB) type. Geochemical analyses show that the melange blocks within the Altyn ophiolitic melange zone have different characteristics from various tectonic environments. This paper recognized such tectonic-lithological assemblages as mid-ocean basalts, oceanic island basalts, oceanic island arc tholeiites, island arc calalkaline basalts and island arc granites and inferred that these tectonic-lithological units respectively belongs to such tectonic units as ophiolites, oceanic islands and/or oceanic seamounts, oceanic island arc and a~creting arcs, which show these blocks from oceanic crust and subduction zone for the most part. For the Altyn ophiolites, the chronological data show they become new from the north to the south. Combined with the study on late slip of Altyn fault and North Qilianshan orogeny, the author inferred that the Altyn region had belonged to one part of the North Qilianshan accreting wedge-arc orogeny at paleozoic, and later huge left-slip made it locate modem site.

新疆东昆仑蛇绿岩岩石学、地球化学特征及其大地构造意义

The East Kunlun area of Xinjiang (briefly EKAX) is the western part of broadly speaking East Kunlun orogenic zone. The absence of geological data (especially ophiolites) on this area has constrained our recognition to its geology since many years. Fund by National 305 Item (96-915-06-03), this paper, by choosing the two ophiolite zones (Muztag and Southwestern Margin of Aqikekule Lake ophiolite zones) exposed at EKAX as the studied objects and by the analysis of thin section, electron probe, XRF, ICP-MS, SEM and Sm-Nd isotope, totally and sys ematically dealt with the field geological, petrological, minerological, petrochemical and geochemical characteristics (including trace, rare earth element and Sm-Nd isotope) and the tectonic setting indicated by them for each ophilite zone. Especially, this paper discussed the trace and rare earth element patterns for metamorphic peridotites, their implications and related them to the other components of ophiolite in order to totally disclose ophiolite origins. Besides, this paper also studied the petrological, geochemical and paleobiological characteristics for the cherts coexsisted with the Muztag ophiolite and the tectonic setting indicated by them. Based on these, the author discussed the tectonic evolution from Proterozoic to Permian for this area. For Muztag ophiolite, their field geological, petrological, minerological, petrochemical and geochemical characteristics show that: ① outcropped along the Muztag-Jingyuhu fault with west-to-east strike, the ophiolite is composed of such three components as metamorphic peridotites, cumulates and volcanic rocks; ② metamophic peridotites consist of such types as lherzolites, serpentinized lherzolites and serpentinites, only pyroxenites is seen of cumulates and volcanic rocks include basalts, basaltic andesites and andesites; ③ mineralogical data on this ophiolite suggest it formed in supra-subduction zone (SSZ)environment, and its mantle wedge is heterogeneous; ④ whole-rock TiO_2 and Al_2O_3 of metamorphic peridotites indicate their original environment with the MORB and SSZ characteristics; ⑤ metamorphic peridotites have depleted LREE and flat REE patterns and volcanic rocks have enriched LREE patterns; ⑥ trace element characteristics of metamorphic peridotites imply that they had undergone Nb and Ta enrichment event after partial melting; ⑦ trace element characteristics of volcanic rocks and their tectonic diagrams show they are formed in the spreading and developed island arc environment with back-arc basin, such as rifted island arc, which is supported by the ε_(Nd)(t) -2.11～+3.44. In summary, the above evidence implies that Muztag ophiolite is formed in SSZ environment, where heterogeneous mantle wedge was metasomatised by the silica-enriched melt from subducted sediments and/or oceanic crust, which makes the mantle wedge enriched again, and this enriched mantle wedge later partially melted to form the volcanic rocks. For Southwestern Margin of Aqikekule Lake ophiolite, their field geological, petrological, minerological, petrochemical and geochemical characteristics show that: ① it outcropped as tectonic slices along the near west-to-east strike Kunzhong fault and is composed of metamorphic perodotties, cumulates and volcanic rocks, in which, chromites are distributed in the upper part of metamorphic peridotites as pods, or in the lower part of cumulates as near-strata; ② metamorphic peridotites include serpentinites, chromite-bearing serpentinites, thlorite-epidote schists and chromitites, of which, chromitites have nodular and orbicular structure, and cumulates include pyroxenits, serpentinites, chromite-bearing serpentinites, chromites and metamorphically mafic rocks and only basalts are seen in volcanic rocks; ③ Cr# of chromites suggest that they formed in the SSZ and Al_2O_3 and TiO_2 of metamorphic peridotites also suggest SSZ environment; ④metamorphic peridotites have V type and enriched LREE patterns, cumulates have from strongly depleted LREE, flat REE to enriched LREE patterns with universally striking positive Eu anomalies and basalts show flat REE or slight enriched LREE patterns with no Eu anomalies; ⑤ trace element and Sm-Nd isotope characteristics of metamorphic peridotites imply their strikingly heterogeneous mantle character(ε_(Nd)(t)+4.39～+26.20) and later Nb, Ta fertilization; ⑥ trace element characteristics of basalts and their tectonic diagrams show they probably formed in the rifted island arc or back-arc basin enviromnent. In summary, the above evidence shows that this ophiolite formed in the SSZ environment and melts from subudcted plate are joined during its formation. Rare earth element, whole-rock and sedimentary characteristics of cherts with the Muztag ophiolite show that they formed in the continental margin environment with developed back-arc basin, and radiolarias in the cherts indicate that the upper age of Muztag ophiolite is early carboniferous. Based on the accreted wedge models of Professor Li Jiliang for Kunlunshan Mountain and combined with study on the two typical ophiolite profiles of EKAX, the author discussed the tectonic evolution of EKAX from Proterzoic to Permian.

铂族元素分析方法研究及其在有关地质问题中的应用

Characterization of Platinum Group Elements (PGE) has been applied to earth, space and environmental sciences. However, all these applications are based on a basic prerequisite, i.e. their concentration or ratio in the research objects can be accurately and precisely determined. In fact, development in these related studies is a great challenge to the analytical chemistry of the PGE because their content in the geological sample (non-mineralized) is often extremely low, range from ppt (10~(-12)g/g) to ppt (10~(-9)g/g). Their distribution is highly heterogeneous, usually concentrating in single particle or phase. Therefore, the accurate determination of these elements remains a problem in analytical chemistry and it obstructs the research on geochemistry of PGE. A great effort has been made in scientific community to reliable determining of very low amounts of PGE, which has been focused on to reduce the level of background in used reagents and to solve probable heterogeneity of PGE in samples. Undoubtedly, the fire-assay method is one of the best ways for solving the heterogeneity, as a large amount of sample weight (10-50g) can be hold. This page is mainly aimed at development of the methodology on separation, concentration and determination of the ultra-trace PGE in the rock and peat samples, and then they are applied to study the trace of PGE in ophiolite suite, in Kudi, West Kunlun and Tunguska explosion in 1908. The achievements of the study are summarized as follows: 1. A PGE lab is established in the Laboratory of Lithosphere Tectonic Evolution, IGG, CAS. 2. A modified method of determination of PGE in geological samples using NiS Fire-Assay with inductively coupled plasma-mass spectrometry (ICP-MS) is set up. The technical improvements are made as following: (1) investigating the level of background in used reagents, and finding the contents of Au, Pt and Pd in carbonyl nickel powder are 30, 0.6 and 0.6ng/g, respectively and 0.35, 7.5 and 6.4ng, respectively in other flux, and the contents of Ru, Rh, Os in whole reagents used are very low (below or near the detection limits of ICP-MS); (2) measuring the recoveries of PGE using different collector (Ni+S) and finding 1.5g of carbonyl nickel is effective for recovering the PGE for 15g samples (recoveries are more than 90%), reducing the inherent blank value due to impurities reagents; (3) direct dissolving nickel button in Teflon bomb and using Te-precipitation, so reducing the loss of PGE during preconcentration process and improving the recoveries of PGE (above 60% for Os and 93.6-106.3% for other PGE, using 2g carbonyl nickel); (4) simplifying the procedure of analyzing Osmium; (5)method detection limits are 8.6, 4.8, 43, 2.4, 82pg/g for 15g sample size ofRu, Rh, Pd, Ir, Pt, respectively. 3. An analytical method is set up to determine the content of ultra-trace PGE in peat samples. The method detection limits are 0.06, 0.1, 0.001, 0.001 and 0.002ng/mL for Ru, Rh, Pd, Ir and Pt, respectively. 4. Distinct anomaly of Pd and Os are firstly found in the peat sampling near the Tunguska explosion site, using the analytical method. 5. Applying the method to the study on the origin of Tunguska explosion and making the following conclusions: (1) these excess elements were likely resulted from the Tunguska Cosmic Body (TCB) explosion of 1908. (2) The Tunguska explosive body was composed of materials (solid components) similar to C1 chondrite, and, most probably, a cometary object, which weighed more than 10~7 tons and had a radius of more than 126 m. 6. The analysis method about ultra-trace PGE in rock samples is successfully used in the study on the characteristic of PGE in Kudi ophiolite suite and the following conclusions are made: (1) The difference of the mantle normalization of PGE patterns between dunite, harzburgite and lherzolite in Kudi indicates that they are residual of multi-stage partial melt of the mantle. Their depletion of Ir at a similar degree probably indicates the existence of an upper mantle depleted Ir. (2) With the evolution of the magma produced by the partial melt of the mantle, strong differentiation has been shown between IPGE and PPGE; and the differentiation from pyroxenite to basalt would have been more and more distinct. (3) The magma forming ophiolite in Kudi probably suffered S-saturation process.

安多地区早中侏罗世岩浆岩岩石地球化学和同位素年代学研究及其对构造演化的制约

Anduo area is located in the Central Tibet, the middle segment of the Bangonghu-Nujiang suture. Anduo Block is the northern part of Lhasa terrane. The relationships among the different geological bodies were determined during the 1: 250000 regional geological surveying. Petrography, petrologic geochemistry, isotopic geochemistry and geochronology of igneous rocks from the suture and granitoids from Anduo Block were analyzed systematically as a whole for the first time. Then, their tectonic setting and history are discussed.Anduo ophiolitic melange consists of metamorphic peridotites, cumulates, plagiogranites, sheeted dykes swarm, pillow lava and radiolarian cherts. The concentration of Cr and Ni in the metamorphic peridotites is very high, with Mg# about 0.94 ~ 0.97, higher 87Sr/86Sr and Pb isotopic ratios, and lower 143Nd/i44Nd ratio. LREE is enriched relative to HREE and positive Eu anomaly is very clear. The REE distribution curve is U shape. Nb and Ta anomalies from cumulate gabbro and sheeted dyke swarm are not clear, while that are slightly negative from pillow lava. Plagiogranite belongs to strong calc-alkaline series with high Si, middle Al, low Fe, Mg and low K contents. Eu anomaly (~ 1.23) from plagiogranites is slightly positive. The character of all components of ophiolite is similar to that of the MORB, while to some extent the ophiolite was influenced by crustal material. Anduo ophiolite formed in a mature back-arc basin. Additionally, intermediate acidity volcanic rocks within Anduo phiolite melange are island arc calc-alkline rocks related to ocean subduction.The early-middle Jurassic plutonic rocks are tonalite, granodiorite bearing-phenocryst, magaporphyritic hornblende monzogranite, magaporphyritic monzogranite, monzogranite bearing-phenocryst and syenogranite in turn. They belong to calc-alkaline series which developed from middle K to high K series temporally. REE distribution curves of all plutonic rocks are similar and parallel to each other. SREE and negative Eu anomaly values decrease. In the multi-element spider diagram, the curves of different plutons are similar to each other, but troughs of Nb, Sr, P and Ti from young plutons become more evident. This suggests that thereare some closely petrogenetic affinities among plutonic rocks which make up amagma plutonism cycle of the early-middle Jurassic. Magma source is mainly crustal,but abundant mafic microgranular enclaves within granitoids indicate that crastalmagma should be mixed with mantle-derived magma and the mantle-derived magmadecreased subsequently. Tonalite has features of I-type granite, magaporphyriticmonzogranite is transition type, and monzogranite bearing-phenocryst is S-typegranite. The characteristic of granitoids from Anduo Block suggest that the formingtectonic setting is active continental margin.Reliable zircon U-Pb SHRIMP ages are obtained in the study area firstly. Plagiogranite from the Anduo ophiolite of the Bangonghu-Nujiang suture is 175.1 Ma, and granitoids from Anduo Block is 172.6-185.4 Ma. Additionally, plagioclase from the plagiogranite dates a 40Ar/39Ar age of 144 Ma, while biotite and hornblend from granitoids of Anduo Block give a 163-165 Ma.Similar cooling ages of plagiogranite from the Anduo ophiolitic melange and granitoids from Anduo Block and the spatial distribution of the ophiolitic rocks between Anduo, Naqu, and Shainzha area suggest that bilateral subduction of the Bangonghu-Nujiang oceanic basin took place in the early-middle Jurassic. During this subduction, Anduo ophiolitic rocks were related to north subduction of the Bangonghu-Nujiang oceanic basin and Anduo back-arc basin spreading, while granitoids from Anduo Block were related to south subduction.