Low power-consumption and high response frequency thermo-optic variable optical Attenuators based on silicon-on-insulator materials

A novel silicon-on-insulator thermo-optic variable optical attenuator with isolated grooves based on a multimode interference coupler principle is fabricated by the inductive coupled plasma etching technology. The maximum fibre-to-fibre insertion loss is lower than 2.2 dB, the dynamic attenuation range is from 0 to 30 dB in the wavelength range 1500-1600 nm, and the maximum power consumption is only 140 mW. The response frequency of the fabricated variable optical attenuator is about 30 kHz. Compared to the variable optical attenuator without isolated grooves, the maximum power consumption decreases more than 220 mW, and the response frequency rises are more than 20 kHz.

A low power consumption thermo-optic variable optical attenuator based on SOI material

A SOI thenno-optic variable optical attenuator with U-grooves based on a multimode interference coupler principle is fabricated. The dynamic attenuation range is 0 to 29 dB; at the wavelength range between 1510 nm and 1610nm, and the maximum power consumption is only l30mW. Compared to the variable optical attenuator without U-groove, the maximum power consumption decreases more than 230mW

AIGaN/GaN HEMTs Power Amplifier MIC with Power Combining at C-Band

A power amplifier MIC with power combining based on AlGaN/GaN HEMTs was fabricated and measured. The amplifier consists of four 10×120μm transistors. A Wilkinson splitters and combining were used to divide and combine the power. By biasing the amplifier at V_(DS) =40V, I(DS)= 0. 9A, a maximum CW output power of 41. 4dBm with a maximum power added efficiency (PAE) of 32. 54% and a power combine efficiency of 69% was achieved at 5. 4GHz.

Heating, current drive and confinement regimes with the JET ICRH and lhcd systems

During its 1990 operation, 2 large RF systems were available on JET. The Ion Cyclotron Resonance Heating (ICRH) system was equipped with new beryllium screens and with feedback matching systems. Specific impurities generated by ICRH were reduced to negligible levels even in the most stringent H-mode conditions. A maximum power of 22 MW was coupled to L-mode plasmas. High quality H-modes (tau-E greater-than-or-equal-to 2.5 tau-EG) were achieved using dipole phasing. A new high confinement mode was discovered. It combines the properties of the H-mode regime to the low central diffusivities obtained by pellet injection. A value of n(d) tau-E T(i) = 7.8 x 10(20) m-3 s keV was obtained in this mode with T(e) approximately T(i) approximately 11 keV. In the L-mode regime, a regime, a record (140 kW) D-He-3 fusion power was generated with 10 - 14 MW of ICRH at the He-3 cyclotron frequency. Experiments were performed with the prototype launcher of the Lower Hybrid Current Drive (LHCD) systems with coupled power up to 1.6 MW with current drive efficiencies up to < n(e) > R I(CD)/P = 0.4 x 10(20) m-2 A/W. Fast electrons are driven by LHCD to tail temperatures of 100 keV with a hollow radial profile. Paradoxically, LHCD induces central heating particularly in combination with ICRH. Finally we present the first observations of the synergistic acceleration of fast electrons by Transit Time Magnetic Pumping (TTMP) (from ICRH) and Electron Landau Damping (ELD) (from LHCD). The synergism generates TTMP current drive even without phasing the ICRH antennae.

Laser diode array side-pumped acousto-optic induced unidirectional operation Q-switched Nd : YAG slab ring laser

A laser-diode array (LDA) side-pumped Nd:YAG slab ring laser is described that incorporates a prism-shaped acousto-optic modulator to enforce unidirectional operation and Q-switching. When pumped by the maximum power of 50 W, Q-switched energies of 3.6 mJ and 50 ns duration, corresponding to a peak power of 72 kW, are obtained. (C) 1999 Society of Photo-Optical Instrumentation Engineers. [S0091-3286(99)01306-9].

Efficient diode-pumped Tm : YALO(3) laser with a pump recycling scheme

By using a pump recycling configuration, the maximum power of 8.1 W in the wavelength range 1.935-1.938 mu m is generated by a 5-mm long Tm:YAlO3 (4 at. %) laser operating at 18 degrees C with a pump power of 24 W. The highest slope efficiency of 42% is attained, and the pump quantum efficiency is up to 100%. The Tm:YAlO3 laser is employed as a pumping source of singly-doped Ho(l%):GdVO4 laser operating at room temperature, in which continuous wave output power of greater than 0.2 W at 2.05 mu m is achieved with a slope efficiency of 9%.

Microcalorimetric study on the toxic effect of Pb2+ to Tetrahymena

The toxic effect of Pb2+ has been studied in eukaryotic cells by using Tetrahymena as a target. The maximum power (P (m)) and the growth rate constant (k) were determined, which showed that values of P (m) and k were linked to the concentration (C) of Pb2+. The addition of Pb2+ caused a decrease of the maximum heat production and growth rate constant, indicating that Tetrahymena growth was inhibited in the presence of Pb2+, and Pb2+ took part in the metabolism of cells. From micrographs, morphological changes of Tetrahymena were observed with addition of Pb2+, indicating that the toxic effect of Pb2+ derived from destroying the membrane of surface of Tetrahymena. According to the thermogenic curves and photos of Tetrahymena under different conditions, it is clear that metabolic mechanism of Halobacterium halobium R1 growth has been changed with the addition of Pb2+.

Application of polyurethane foam units and calorimetry to microbial monitoring in Lake Donghu

Combined with the national standard biomonitoring method (polyurethane foam units method), calorimetry was applied to study the metabolic activities of PFU microbial communities in fresh water to determine the effects of anthropotgenic stresses on the activity of the microbial community. Comparisons were made at four sampling stations with different eutrophic status in Lake Donghu. Water quality variables, species number of protozoa, abundances of microorganisms, biomass, heterotrophy indexes and diversity indexes are reported. The heat rate-time curves of the native and concentrated PFU microbial communities were determined at 28 degrees C. Growth rate, measured maximum power output and total heat were calculated from the heat rate-time curves. The values of metabolic variables are higher at the more eutrophic stations, which suggests that organic pollution increases the activity of PFU microbial communities. The metabolic variables are in good agreement with chemical and biotic variables. And calorimetry will be useful for biomonitoring of the PFU microbial community. (C) 2005 Elsevier B.V. All rights reserved.

Organic light emitting diodes using magnesium doped organic acceptor as electron injection layer and silver as cathode

Organic light emitting diodes employing magnesium doped electron acceptor 3, 4, 9, 10 perylenetetracarboxylic dianhydride (Mg: PTCDA) as electron injection layer and silver as cathode were demonstrated. As compared to Mg: Ag cathode, the combination of the Mg: PTCDA layer and silver provided enhanced electron injection into tris (8-quinolinolato) aluminium. The device with 1: 2 Mg: PTCDA and Ag showed an increase of about 12% in the maximum current efficiency, mainly due to the improved hole-electron balance, and an increase of about 28% in the maximum power efficiency, as compared to the control device using Mg: Ag cathode. The properties of Mg: PTCDA composites were studied as well.

Organic light emitting diodes with an organic acceptor/donor interface involved in hole injection

Organic light emitting diodes with an interface of organic acceptor 3-, 4-, 9-, 10-perylenetetracarboxylic dianhydride (PTCDA) and donor copper phthalocyanine (CuPc) involved in hole injection are fabricated. As compared to the conventional device using a 5 nm CuPc hole injection layer, the device using an interface of 10 nm PTCDA and 5 rim CuPc layers shows much lower operating voltage with an increase of about 46% in the maximum power efficiency. The enhanced device performance is attributed to the efficient hole generation at the PTCDA/CuPc interface. This study provides a new way of designing hole injection.

Multimode-interference-type thermo-optic variable optical attenuator with a response frequency of 10 kHz

A thermo-optic variable optical attenuator based on a multimode interference coupler principle is fabricated. The propagation loss of the fabricated device is 1.6 to 3.8 dB at the wavelength range 1510 to 1610 nm, which is very near the calculated value (1.2 dB) by the finite difference beam propagation method. The maximum power consumption is 363 mW and the dynamic attenuation range is 0 to 26 dB. The response frequency of the fabricated attenuator is about 10 kHz. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

High-performance strain-compensated InGaAs/InAlAs quantum cascade lasers

We report on the realization of quantum cascade (QC) lasers based on strain-compensated InxGa(1-x)As/In(y)A((1-y))As grown on InP substrates using molecular beam epitaxy. X-ray diffraction and cross section transmission electron microscopy have been used to ascertain the quality of the QC laser materials. Quasi-continuous wave lasing at lambda approximate to 3.54-3.7 mum at room temperature was achieved. For a laser with 1.6 mm cavity length and 20 mum ridge-waveguide width,quasi-continuous wave lasing at 34 degreesC persists for more than 30 min, with a maximum power of 11.4 mW and threshold current density of 1.2 kA cm(-2), both record values for QC lasers of comparable wavelength.

Electro-Optical Effect Measurement of Thin-Film Material Using PM Fiber Mach-Zehnder Interferometer

A polarization-maintaining (PM) fiber Mach-Zehnder (MZ) interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer,all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here, we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.

无介体双室微生物燃料电池产电性能初步研究

本文对无介体双室微生物燃料电池的产电性能进行了初步研究，并根据不同运行阶段产电性能的优劣，对其中微生物的差异性进行了比较分析。全文分为两个部分： 第一部分：以乙酸钠为阳极原料构建双室微生物燃料电池（MFC），研究不同阴极受体、外接电阻、乙酸钠浓度和pH等因素对电池产电性能的影响，研究结果表明：在500mL的阴阳极反应体系中，选用乙酸钠作为阳极底物，质量浓度为6.46 g/L， pH 7.0，接入500Ω外电阻，阴极电子受体选择高锰酸钾的情况下，微生物燃料电池产电性能最好，最大电功率密度达到294.72 mW/m2，库伦效率能达到25.87%。在确定最适外接电阻阻值的同时对MFC内阻进行测定，阻值为871.87Ω。 第二部分：微生物燃料电池运行中，比较以厌氧污泥作为接种源的第一阶段和只接入附着有大量微生物电极的第二阶段的产电性能，得出第二阶段产电性能优于第一阶段，最大电功率密度达到353.57mW/m2，比第一阶段提高58.85 mW/m2；库伦效率为39.35%，增幅达52％左右；针对微生物燃料电池运行过程中，底物CH3COONa可能存在其它的代谢途径，本实验进行了第二阶段产电性能与CH3COONa消耗率关系以及阳极液面上方气体成分和含量的研究，发现第二阶段50h前CH3COONa的大量消耗主要用于微生物的生长，在整个运行过程中，阳极液面上方含有CH4和CO2；对气体测定的同时还发现，振荡能增强电功率密度的输出；通过对电极上和污泥中微生物差异性分析得出，δ-变形菌纲、β-变形菌纲和拟杆菌门的菌种更适应微生物燃料电池的运行环境，能在电极上大量富集，提高电池的产电性能，只接入附着有大量微生物的电极能有效降低热袍菌纲的菌种数量，降低了CH3COONa的无为消耗，有效提高了电池的库伦效率。 Electricity production in the mediator-less two-chambered microbial fuel cell(MFC) was researched. Based on the result in the different operation phase in the MFC, the microbial diversity was analysed. The paper involved two parts: Part 1: A two-chambered microbial fuel cell (MFC) was constructed with high-concentration sodium acetate as fuel in the anode. The influence of different electron acceptors in the cathode, external resistance value, pH value and concentration of sodium acetate on electricity generation in MFC was investigated. The result showed that the maximum power density of 294.72 mW/m2 and the coulombic efficiency of 25.87% was achieved at sodium acetate concentration of 6.46 g/L, pH 7.0, external resistance 500Ωin the anode and when using potassium permanganate as electron acceptor in the cathode. While decided the value of resistor, we found that shaking has effect on electricity production in the MFC. Part 2: Comparing the electricity production in different operation phases when using anaerobic sludge as inoculum in the first phase and microbes in the anodic electrode as inoculum in the second phase, the result showed that electricity production in the second phase was more than that in the first phase, the maximum power density of 353.57 mW/m2 and the coulombic efficiency of 39.35% was achieved, 58.85 mW/m2 and 52％ more than that in the first phase, respectively. According to the fact that CH3COONa might be metabolized in other pathway in the running process in the MFC, we determining the relationship between electricity production and CH3COONa consumption, and the gas content in the anode, we found that CH3COONa was mainly used for microbe growth before 50h, and the anode contained CH4 and CO2. At the same time, we found that shaking could improve power density. The analysis on diversity of microbe in the anodic electrode and anaerobic sludge showed that δ-proteobacterium, β-proteobacterium and Bacteroidetes adapted themselves to the running environment of MFC. The anode could enrich them to improve the electricity production while reduced the quantity of Thermotogales, which were obligately anaerobic organotrophs with a fermentative metabolism, to increase the coulombic efficiency effectively.

冷却储存实验环功率源的设计与计算

RF system of HIRFL-CSRe(cooling storage experimental ring)was designed by ourselves and manufactured domestically,which operates in the frequency range of 0.5~2.0 MHz at first and second harmonic modes.Based on detailed engineering calculation,the design of RF generator was completed.It will work not only in CW mode but also in the mode of ramping pulse modulation,and the maximum power is up to 70 kW.It satisfies the requirement of 10 kV maximum deceleration voltage to capture the irradiative beam and decel...中文摘要：对兰州重离子加速器冷却储存环实验环(CSRe)的高频系统功率源的设计作了详细的工程计算,工作频率范围为0.5～2.0MHz,工作于基波及二次谐波模式,发射机不仅能工作于点频连续波模式,而且还可以工作在扫频调制模式,输出最大功率达到70kW。满足最高加速或减速电压10kV的设计要求,能够用于捕获放射性次级束并将束流的能量从400MeV/u减速到30MeV/u。