潘洛铁矿滑坡特征分析及防治

分析了潘洛铁矿露天矿滑坡灾害发生发展的特征,得出该滑坡是一个动态的、多层次的复合型滑坡;找出了影响该边坡稳定的主要因素是大气降雨和采矿切割坡脚;根据这些影响因素和滑坡发展变化规律,提出了科学合理的滑坡治理方案,即动态的综合治理方案.经现场实施后,通过滑坡监测数据表明,该滑坡得到了彻底根治.

山东莱芜中生代高镁侵入岩及其超镁铁质岩捕掳体的成因研究

In order to know better about the Phanerozoic lithosphere thinning process of Sino-Korea Plate, four Cretaceous intrusion complexes and their ultramafic xenoliths are investigated by this thesis, which are located in Laiwu, Shandong Province, Eastern China, a region far away from plate margin. The four complexes, Kuanshan, Jiaoyu, Jingniushan and Tietonggou, intruded into Archaeozoic granite gneiss and Paleozoic carbonate rocks with scam iron ore at their contact zone. The four complexes can be divided into two magma series, abyssal rocks for the early and hypabyssal rocks for the later. K-Ar dating show that the abyssal rocks intrusion began with 120 ±2 Ma and the hypabyssal rocks intruded about 113 Ma. Abyssal rocks, mainly made up of augite diorites, amphibole diorites and gabbros for the lesser, are chemically characterized with high-Mg (Mg#>0.5) high-K calcalklic rock, which are depleted with Nb, Ta and Ti related to LILE and extremely enriched with Sr and Pb. Comparatively, augite diorites are the most LREE enriched in abyssal rocks, and they show no Eu abnorrnity or weak positive Eu abnormity. Gabbros show the least LREE enrichment with a strong Eu abnormity relatively. In (~(87)Sr/~(86)Sr)_1 -ε Nd(T) diagram, the abyssal rocks show a mixing trend , a rapid change in ε Nd(T) with a relatively small change in (~(87)Sr/~(86)Sr)_1. Low radiogenic Sr and Pb composition with high radiogeic Nd composition indicate that the mixing processes happened in lower crust Melt-rock interactions in lower crust might be the most possible processes to produce these high-Mg and high-K calcalklic magmas. Hypabyssal rocks, mainly made up of granite porphyry and dioritic porphrite, show much higher ε Nd(T) than abyssal rocks. Granite porphyry are distinct with an adakite geochemical characteristics, high (La/Yb)_N, Sr/Y and low Rb/Sr ratio. The adakitic granite porphyry indicates a new lower crust produced by underplating within plate. Ultramafic xenoliths had been found only in augite diorites and amphibole diorites. Field investigations show that ultramafic xenoliths in augite diorites had been inherited from amphibole diorites, so ultramafic xenoliths had been only entrained by hydrous dioritic magma. Ultramafic xenoliths are mainly made up of dunite and harzburgite, orthopyroxenite and bistangite are the lessor. Coarse olivines in dunite often show many chromite exsolution lamellae. Opx in orthopyroxenite often show dense chromite exsolution lamellae. The presence of exsolution minerals indicates that ultramafic xenoliths had cooled before entraining. Metasomatism phenomenons are popular in dunite and harzburgite xenoliths, including two kinds of assemblage, cpx+phlogapite and opx+pl. The first metasomatism assemblage indicates an ancient enrichment. Rb-Sr dating of xenoliths shows that the ancient enrichment happened in 223 ± 7Ma. The second metasomatism assemblage indicates a recent, relatively not deep melt-rock interaction, which might be related with the genesis of the high-Mg high-K calcalklic rocks. Mineralogy and geochemistry indicate that these ultramafic xenoliths might sample the crust-mante transition zone (or the base of lower crust, moho). Investigation of high-Mg intrusions and their ultramafic xenoliths in Laiwu indicate that the thinning processes of Sino-Korea Plate can be divided into two stages. The first stage is lithosphere mantle thinning with crust thickening by underplating in lower crust. The second stage is that the thickened lower crust delaminated into the underlying mantle.

Microstructural features of an iron-based laser coating

A high toughness wear resistant coating is produced by laser clad Fe-Cr-W-Ni-C alloys. The microstructural and compositional features of the laser-solidified microstructures and phase evolutions occurring during high temperature tempering at 963 K were investigated by using analytical electron microscopy with energy dispersive X-ray analysis. The clad coating possesses the hypereutectic microstructure consisted of M7C3 + (Y + M7C3) Du ring high temperature aging, the precipitation of M23C6 and M2C in austenite and in situ transformation of dendritic M7C3 to M23C6 and eutectic M7C3 to M6C occurred. The laser clad coating reveals an evident secondary hardening and superior impact wear resistance.

Feasibility of Laminar Plasma-Jet Hardening of Cast Iron Surface

Nontransferred DC laminar plasma jets of stable flow and low impinging pressure acting on the substrate were used to heat W–Mo–Cu cast iron for phase transfer hardening of the surface layer. Substrates were heated in multipass with or without overlapping or heated with only single-pass. Surface morphologies of the molten trace and microstructure of the cross-section were observed, and the hardness distribution of the treated surface layer was examined. The surface layer of single-pass-heated specimen has an average hardness of about 900 HV0.1, while the specimen treated with multipass shows an average hardness of about 700 HV0.1, because of the heat effect from the neighboring pass treating, compared with the substrate hardness of about 300 HV0.1. The results demonstrate the stable and favorably controlled heating of the laminar plasma jet on the substrate surface and feasibility of using it as a tool for surface hardening of cast iron.

Application of Three-Dimensional Discrete Element Face-to-Face Contact Model with Fissure Water Pressure to Stability Analysis of Landslide in Panluo Iron Mine

Three-dimensional discrete element face-to-face contact model with fissure water pressure is established in this paper and the model is used to simulate three-stage process of landslide under fissure water pressure in the opencast mine, according to the actual state of landslide in Panluo iron mine where landslide happened in 1990 and was fathered in 1999. The calculation results show that fissure water pressure on the sliding surface is the main reason causing landslide and the local soft interlayer weakens the stability of slope. If the discrete element method adopts the same assumption as the limit equilibrium method, the results of two methods are in good agreement; while if the assumption is not adopted in the discrete element method, the critical phi numerically calculated is less than the one calculated by use of the limit equilibrium method for the same C. Thus, from an engineering point of view, the result from the discrete element model simulation is safer and has more widely application since the discrete element model takes into account the effect of rock mass structures.

Nonequilibrium microstructures and phase evolutions of an iron-based laser clad coating

The microstructural and compositional features of the laser-solidified microstructures and phase evolutions occurring during high temperature tempering were investigated by using analytical electron microscopy with energy dispersive X-ray analysis. The cladded alloy, a powder mixture of Fe, Cr, W, Ni and C with a weight ratio of 10:5:1:1:1, was processed with a 3 kW continuous wave CO2 laser. The cladded coating possessed the hypoeutectic microstructure of the primary dendritic gamma-austenite and interdendritic eutectic consisting of (gamma+M7C3). The gamma-austenite is a nonequilibrium phase with extended solid solution of alloying elements. And, a great deal of fine structures, i.e., a high density of dislocations, twins, and stacking faults existed in austenite phase. During high temperature aging, the precipitation of M23C6, MC and M2C in austenite and in situ transformation of M7C3(+gamma) --> M23C6 and M7C3+gamma --> M6C occurred. The laser clad coating revealed an evident secondary hardening and superior impact wear resistance.

Rapidly solidified nonequilibrium microstructure and phase transformation of laser-synthesized iron-based alloy coating

The rapidly solidified microstructural and compositional features, the precipitation and transformation of carbides during tempering, and the impact wear resistance of an iron-based alloy coating prepared by laser cladding are investigated. The clad coating alloy, a powder mixture of Fe, Cr, W, Ni, and C with a weight ratio of 10:5:1.1.1, is processed using a continuous wave CO, laser. Microstructural studies demonstrate that the coating possesses the hypoeutectic microstructure comprising the primary dendritic gamma-austenite and interdendritic eutectic consisting of gamma-austenite and M7C3 carbides. gamma-Austenite is a non-equilibrium phase with an extended solid solution of alloying elements. During high temperature tempering at 963 K for 1 h, the precipitation of M23C6, MC and M2C carbides in austenite and in situ carbide transformation of M7C3 to M23C6 and M7C3 to M6C respectively are observed. In addition, the microstructure of the laser-clad coating reveals an evident secondary hardening and a superior impact wear resistance.

Molecular dynamics studies on dislocations in crystallites of nanocrystalline alpha-iron

Molecular dynamics simulations have been carried our to study the atomic structure of the crystalline component of nanocrystalline alpha-iron. A two-dimensional computational block is used to simulate the consolidation process. It is found that dislocations are generated in the crystallites during consolidation when the grain size is large enough. The critical value of the grain size for dislocation generation appears to be about 9 nm. This result agrees with experiment qualitatively. AN dislocations that are preset in the original grains glide out during consolidation. It shows that dislocations in the crystallites we generated in consolidation process, but not in the original grains. Higher consolidation pressure results in more dislocations. Furthermore, new interfaces are found within crystallites. These interfaces might result from the special environment of nanomaterial. (C) 1998 Acta Metallurgica Inc.

Microstructure Evolution of Laser Pulse processed Ductile Iron Surface

Pulsed laser beam was used to modify surface processing for ductile iron. The microstructures of processed specimen were observed using optical microscope (OM). Nanoindentation and micro-hardness of microstructures were measured from surface to inner of sample. The experimental results show that, modification zone is consisted of light melted zone, phase transformation hardening area and transient area. The light melt area is made up of coarse dendrite crystalline with a thickness less than 20um, phase transformation hardening area mainly of laminal or acicular martensite, retained austenite and graphite, i.e. M+A prime+ G. The cow-eye microstructure around graphite sphere always is formed in phase transformation hardening area zone, which consisting of a variety structure with the distance from the surface. So, it maybe as a obvious sign distinguishing modification zone border. Finally, the microstructures evolution of laser pulse processed ductile iron was analyzed coupling with beam energy distribution in space and laser pulse heating procession characteristics. The analysis shows that energy distribution of laser pulse has an important effect on microstructure during laser pulse modified ductile iron. Multi-scale and interlace arrangement are the important features for laser pulse modified ductile iron. Of microstructure.

Measurements Of In Situ Stress And Mining-Induced Stress In Beiminghe Iron Mine Of China

In order to obtain the distribution rules of in situ stress and mining-induced stress of Beiminghe Iron Mine, the stress relief method by overcoring was used to measure the in situ stress, and the MC type bore-hole stress gauge was adopted to measure the mining-induced stress. In the in situ stress measuring, the technique of improved hollow inclusion cells was adopted, which can realize complete temperature compensation. Based on the measuring results, the distribution model of in situ stress was established and analyzed. The in situ stress measuring result shows that the maximum horizontal stress is 1.75-2.45 times of vertical stress and almost 1.83 times of the minimum horizontal stress in this mineral field. And the mining-induced stress measuring result shows that, according to the magnitude of front abutment pressure the stress region can be separated into stress-relaxed area, stress-concentrated area and initial stress area. At the -50 m mining level of this mine, the range of stress-relaxed area is 0-3 m before mining face; the range of stress-concentrated area is 3-55 m before mining face, and the maximum mining-induced stress is 16.5-17.5 MPa, which is 15-20 m from the mining face. The coefficient of stress concentration is 1.85.