Influence of the size of ultrafine CaCO3 powder on PP crystallization

The effects of CaCO3 on the crystallization behavior of polypropylene (PP) were studied by means of DSC and WAXD. The average sizes of the CaCO3 powders used were 0.1 mum (UC) and 0.5 mum (GC), respectively. The PP/CaCO3 composites at compositions of 1 phr and 10 phr were investigated. The results showed that the addition of CaCO3 reduced the supercooling, the rate of nucleation and the overall rate of crystallization (except for the 10 phr UC/PP sample). The crystallinity of PP was increased and the size distribution of the crystallites of alpha -PP; was: broadened. On the other hand,the crystallization rate of 10 phr UC/PP is 1.5 times higher than that of neat PP. It has an overall rate of crystallization 2 times as much as that of the neat PP and has the maximum crystallinity. The sizes of crystallites and the unit cell parameters of alpha -PP were varied by the addition of CaCO3. beta -PP was formed by addition of Ge and was not detected by addition of UC. The differences of crystallization behaviors of PP might be attributed to the combined effects of the content and size of CaCO3 filled.

Shear-enhanced crystallization of a thermoplastic polyimide derived from 3,3 ',4,4 '-oxydiphthalic dianhydride and 4,4 '-oxydianiline

The aim of this work is to investigate the effect of consecutive shear on the crystallization of an amorphous aromatic polyimide (PI) derived from 3,3',4,4'oxydiphthalic dianhydride (3,3',4,4'-ODPA) and 4,4-oxydianiline (ODA). At 260 degrees C, the increase of shear rate or shear time leads to the increase of crystallinity. Indeed, increasing shear rate can also accelerate the crystallization behavior. Moreover, it was found that a new melting peak appeared at higher temperature for long time or high rate sheared sample. The enhancement of crystallization behavior appears directly linked to the increase of crystal thickness. Particularly, the effect of shear temperature was investigated, and the results revealed that the crystallization of the PI was more sensitive to shear at 260 degrees C, which was 10 degrees above the glass transition temperature (250 degrees C) of the PI. Possible mechanism was proposed to illustrate the effect of consecutive shear on the crystallization of the PI polymer.

Influence of shear on crystallization behavior of the beta phase in isotactic polypropylene with beta-nucleating agent

Wide-angle X-ray diffraction (WAXD) was used to investigate the effects of shear on the crystallization behavior of polypropylene (PP) with beta-nucleating agent. The melt was subjected to shear at the shear rate from 0.5 to 60 s(-1) for 5 s with a CSS450 shear stage. For the PP with low content of the additive, the formation mechanism of the beta crystals is almost the same as that of pure isotactic polypropylene (iPP), viz., shear induces. Otherwise, for the samples with high content of the additive, the formation mechanism of the beta form are nucleating agent induces. The results clearly show that shear restrains the formation of high beta phase for the melt with additive.

A polymer composite film with reversible responsive behaviors

A responsive polymer composite film was generated by the use of reversibly switchable Surface morphology of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) films in response to different block selective solvents on the rough isotactic poly(propylene) (i-PP) substrate. The Maximum difference of the water contact angle of the composite films increased from 22.6 degrees of PS-b-PMMA films on the smooth substrate to 42.6 degrees when they were treated by PS and PMMA selective solvents, respectively. The mechanisms of the responsive extent enhanced and the superhydrophobicity of the composite films were discussed in detail.

Crystallization and phase behavior of crystalline syndiotactic 1,2-polybutadiene/isotactic polypropylene blends in solution-cast thin films

Crystallization and phase behavior in solution-cast thin films of crystalline syndiotactic 1,2-polybutadiene (s-1,2-PB) and isotactic polypropylene (i-PP) blends have been investigated by transmission electron microscopy (TEM), atomic force microscopy (AFM) and field-emission scanning electron microscopy (FESEM) techniques. Thin films of pure s-1,2-PB consist of parallel lamellae with the c-axis perpendicular to the film plane and the lateral scale in micrometer size, while those of i-PP are composed of cross-hatched and single-crystal-like lamellae. For the blends, TEM and AFM observations show that with addition of i-PP, the s-1,2-PB long lamellae become bended and i-PP itself tends to form dispersed convex regions oil a continuous s-1,2-PB phase even when i-PP is the predominant component, which indicates a strong phase separation between the two polymers during film formation. FESEM micrographs of both lower and upper surfaces of the films reveal that the s-1,2-PB lamellae pass through i-PPconvex regions from the bottom, i.e. the dispersed i-PP regions lie on the continuous s-1,2-PB phase. The structural development is attributed to an interplay of crystallization and phase separation of the blends in the film forming process.

Neodymium oxide-assisted melt free-radical grafting of maleic anhydride on isotactic-polypropylene by reactive extrusion

Rare earth oxide, neodymium oxide (Nd2O3), -assisted melt free-radical grafting of maleic anhydride (MAH) on isotactic-polypropylene (i-PP) was carried out by reactive extrusion. The experimental results reveal that the addition of Nd2O3 into reactive system leads to an enhancement of the grafting degree of MAH, along with an elevated degradation of i-PP matrix. When Nd2O3 content is 4.5 mmol %, the increment of the grafting degree of MAH (maximally) is up to about 30% compared with that of the related system without adding Nd2O3, while the severest degradation of i-PP matrix simultaneously occurs. On the basis of the reaction mechanism of PP-g-MAH proposed before, the sequence of beta-scission and grafting reaction is discussed in detail. It is found that, for the reactive system studied, most tertiary macroradicals first undergo beta-scission, and then, grafting reaction with MAH takes place at the new radical chain ends. The imported Nd2O3 has no effect on the aforementioned reaction mechanism, whereas it enhances the initiating efficiency of the initiator, dicumyl peroxide (DCP).

酚酞型聚芳醚砜共聚物与共混物－(PP/BiS-T) PES共聚物和(PPS/PES-C)、(PPO/PES-C)共混物的合成、结构与性能研究

本工作旨在通过共聚、共混技术制备酚酞型聚芳醚砜共聚物(PP/BiS-T) PES和共混物(PPS/PES-C)、PPO/PES-C，以便改善酚酞型聚芳醚砜（PES－C）的加工性能（特别是注射加工性能）和耐溶剂性能。通过研究共聚物和共混物的微观结构，聚集态结构与性能的关系，探索改善酚酞型聚芳醚硕性能的有效途径第一部分：(PP/BiS-T) PES共聚物的合成、结构与性能(PP/BiS-T) PES共聚物是以4，4'二氯二苯砜（DCDPS）、酚酞（PP）和4，4'－二羟基二苯硫醚(BiS-T)为单体，采用固体无水K_2CO_3/NMP/TMSO_2 混合溶剂反应体系合成的。共聚反应规律研究表明：在NMP/TMSO_2混合溶剂中，共聚反应可以顺利进行，避免了交联反应的发生，并成功地合成了高分子量的(PP/BiS-T) PES共聚物。DSC分析结果表明(PP/BiS-T) PES系列属于无定形的均相共聚物体系，每一组成比例对应的共聚物只具有一个玻璃化转变温度。且随组成比例的改变呈线性变化，TBA分析结果与DSC基本一致，并证实了(PP/BiS-T) PES属于均相共聚物体系，而不是均聚物的共混物。TG分析表明：共聚物具有良好的耐热氧化稳定性BiS-T链节在分子链中起到了提高自身抗氧性的作用。1R光谱对共聚物的结构进行表征。~(13)C-NMR分析确认共聚物多属于无规共聚物。动态力学试验表明共聚物(PP/BiS-T) PES以及PES－C，在－100 ℃附近和0－100 ℃，存在着次级松驰与转变，并发现水分子的存在对这种转变（次级松驰）有一定的影响。共聚物的熔融流动性试验和溶解性试验表明共聚物(PP/BiS-T) PES具有稍好于PES－C的熔融流动性；溶解性与PES－C类似。力学试验说明共聚物属于强而硬类型的聚合物。第二部分：PPS/PES－C共混物的制备、聚集态结构与性能PPS/PES－C共混物是以联苯/二苯硕混合物为溶剂，采用溶液沉析方法制备的，DSC、WAXD，SEM和1R分析手段对共混物的聚集态结构和微观结构进行了表征。DSC分析认为共混物属于多相体系，PPS的结晶性随着PES－C含量增加而降低。DSC和SEM观察结果表明：相转变发生在PPS占40％左右。PPS占25％时，DSC曲线呈现出界面相玻璃化转变温度。共混物具有良好的耐热氧化稳定性和耐热分解稳定性。微晶大小计算结果：PES－C存在导致了PPS微晶大小降低。WAXD曲线表明PPS占50％，共混物中的PPS具有较好的结晶性。SEM观察发现：随着PES－C含量增加，PES－C由分散相（PES－C50％）变为连续相（PES－C70％）。PPS占50％或低于50％时，共混物体系不仅发生了微观相分离，而且发生了宏观相分离。M.I.指数表明共混物中PPS为连续相时，共混物具有良好的熔融流动性。溶解性试验结果：共混物具有较好的耐溶剂性。第三部分：PPO/PES－C共混物的合成、结构与性能 PPO/PES－C共混物系用溶液－涂膜法，以氯彷为溶剂制备的。讨论了由同一共混物溶液浓度下制备的共混物的互溶性随组成的改变而变化。DSC分析结果：PPO/PES－C属于部分相溶性体系。利用Fox方程推导式计算结果表明PPO在富PES－C相中具有良好的分散性；而PES－C在富PPO相中的分散性较差。共混物(PPO/PES－C)试样经丙酮浸泡后，PPO（>50％）发生了溶剂诱导结晶现象，同时丙酮促使共混物发生完全相分离。结晶溶化热显示共混物中少量的PES－C存在有利于PPO的溶剂诱导结晶。TG分析表明共混物具有良好的耐热分解稳定性和耐热氧化分解稳定性。偏光显微镜下观察到PPO球晶的存在。SEM和FT－1R分别对共混物的形态结构和微观结构进行了表征。WAXD试验证实了丙酮处理的(PPO/PES－C)（70/30），（90/10）共混物中PPO的结晶性。溶解性试验表明：PPO掺入有助于 PES－C的耐溶剂性提高。

Rheology and morphology of reactively compatibilized PP/PA6 blends

This work aims to use the Palierne emulsion type model to describe the relationship between the rheological response to small amplitude oscillatory deformation and morphology of polypropylene/polyamide 6 (PP/PA6) blends compatibilized with maleic anhydride grafted polypropylene (PP-g-MAH). It was found that the Palierne emulsion type model could describe very well the linear viscoelastic responses of binary uncompatibilized PP/PA6 blends and failed to describe the ternary compatibilized PP/PP-g-MAH/PA6 blends. These features could be attributed to the fact that the morphology of the ternary blends was not of the emulsion type with the PA6 particles dispersed in the PP matrix but of an emulsion-in-emulsion type, i.e., PA6 particles dispersed in the PP matrix themselves contained PP or PP-g-MAH inclusions. By consideration of PP-in-PA6 particles as pure PA6 particles, where the volume fraction of the PA6 phase was increased accordingly, the Palierne emulsion type model could work very well for a ternary blending system. Preshear at low frequencies modified the morphology of both binary and ternary blends. The particles of the dispersed phase (PA6) became more uniform. These results suggested that the Palierne emulsion type model could be used to extract information on rheological properties and interfacial tension of polymer blends from known morphology and vice versa.

Hydrophobic pocket modification and humanized catalytic antibodies with glutathione peroxidase activity (I) - Preparation and characterization of haptenes and conjugates

The thiol group of glutathione (GSH) was protected by 2,4-dinitrochlorobenzene (DNCB), the product S-substituted dinitrophenyl GSH(GSH-S-DNP) was alcoholized to obtain haptenes 4 and 5 respectively. As haptenes, the two GSH derivatives were characterized by means of H-1 NMR, MALDI-TOF-MS and IR, followed by individually coupling with bovine serum albumin (BSA) via glutaraldehyde. BSB-Hp4 and BSA-Hp5 were purified by Sephadex G-25 gel filtration chromatography. For each conjugate, the average haptene-BSA ratio was 12 : 1. The electrophoresis analysis showed that the average molecular weight of each conjugate was 76 500. The CD spectrum indicated that the conjugates had more a-helix content than BSA did.